In our production and life, Capping Machine is also called a Capping Machine, Capping Machine, or Capping Machine, which is used for screwing and unscrewing the caps of plastic bottles and glass bottles (molded bottles or tube bottles). equipment. Capping Machine is highly intelligent capping equipment with advanced technology, unique design, and easy operation. During the entire capping process, workers only need to place the cap on the mouth of the bottle, and then the bottle is automatically sent to the capping wheel and automatically tightened to complete the capping operation. The Capping Machine evacuates the packaging bottle and then tightens it, which prolongs the storage time of the packaging, reduces the failure rate of the Capping Machine, and improves the packaging efficiency of the Capping Machine. So what are the matters needing attention when operating Capping Machine correctly? Let's take a look together next.
This is the content list:
l Capping Machine rolling wheel adjustment
l Capping Machine lock wheel adjustment
l Capping Machine cap lock
l Capping Machine height adjustment
Capping Machine rolling wheel adjustment
Place the Capping Machine bottle on the bracket and raise the bracket to the highest point. First, loosen the lock nut to adjust the rolling wheel so that the (sprung) edge of the two Capping Machine rolling wheels is at the threading of the bottle. Click on it, then loosen the lock nut, and then adjust the adjusting screw so that the edges of the two rolling wheels are in contact with the cover, and a little pressure is appropriate, and then tighten the nut.
Capping Machine lock wheel adjustment
Adjust the two Capping Machine locking wheels, first loosen the locking nuts, adjust the locking wheels so that the edges of the two locking wheels are in contact with the lower edge of the bottle cap, a little pressure is appropriate, and then tighten the nuts (Note: Adjust Capping Machine Should be from loose to tight, adjust while pulling the lock).
Capping Machine cap lock
Loosen the top screw, remove the Capping Machine gland head, and then remove the entire Capping Machine lock head, install the appropriate plastic lock head on the cone sleeve, and then adjust the lifting height of the bracket to meet the working requirements.
Capping Machine height adjustment
Start the Capping Machine to lower the bracket to the lowest point, then place the bottle on the bracket, loosen the brake nut, turn the adjusting screw to raise the bracket, and then adjust the appropriate distance between the cap of the Capping Machine and the capping head (generally All are adjusted in place at the factory).
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. We have obtained ISO9001 quality management system certification, and some products have passed CE certification. Our company has obtained more than 20 invention patents and utility model patents. If you are interested in Capping Machine, you can contact us, our website is www.cnzpack.com.
With the increasingly fierce competition in the manufacturing and production of plastic bottles in the food and pharmaceutical industries, Bottle Unscrambler has become more and more solid backing for the food and pharmaceutical plastic bottle markets. So how does it play a role? We will introduce the work process and personnel operation specifications of Bottle Unscrambler. Let's take a look together next.
This is the content list:
The workflow of Bottle Unscrambler
Personnel operation specification of Bottle Unscrambler
The workflow of Bottle Unscrambler is generally as follows: manually put materials into the storage bottle library, the materials in the storage bottle library will be automatically quantified and fed to the turntable at the set speed. The turntable rotates at a high speed to supply the bottles as required, the web wheel The irregular bottles are removed, and the bottle dividing part sends the bottles from the turntable to the bottle unscramble part at a certain speed. The Bottle Unscrambler part of the Bottle Unscrambler clamps the bottles to the working surface of the conveyor through the conveyor belts on both sides, and at the same time sorts the bottles through the bottle turner. The Bottle Unscrambler electronic control system performs real-time monitoring and feedback through the sensors of each part to achieve fully automated operation requirements, and save a lot of labor costs and avoid losses caused by human error factors.
To ensure the normal and safe operation of Bottle Unscrambler, there are special operating procedures established for it. Operators and equipment management personnel shall perform standardized operations of Bottle Unscrambler under these procedures. This safe operation specification is commonly used in Bottle Unscramblers, mixers, high-speed automatic Bottle Unscramblers, etc.
1. First check the Bottle Unscrambler's intact, clean, and expiration status identification and the equipment operation record of the shift. If the inspection finds that the Bottle Unscrambler has exceeded the cleaning validity period, it is necessary to further clean the equipment according to the equipment cleaning operation rules and fill in the equipment status identification.
2. Check the Bottle Unscrambler and the Bottle Unscrambler to confirm that there is no foreign matter, and turn the bottle plate and unscrambler to confirm that it can work normally.
3. Turn on the Bottle Unscrambler power switch, check the touch screen and three photoelectric switches. If both are energized, the lack of a bottle alarm will be displayed on the touch screen. When the electric eye is blocked by hand, the screen displays the blocking alarm, and the two photoelectric switches are in a normal state.
4. Turn on the Bottle Unscrambler compressed air, use the bottom of the bottle to shake under the electric eye of the bottle puller, compressed air will be sprayed out, and the equipment can be turned on normally.
To ensure that the various parts of the Bottle Unscrambler can work normally, the formal operation can be divided into five steps: click the host start and lift start on the touch screen respectively, and observe whether the Bottle Unscrambler has abnormal noise when it is running. After powering on the Bottle Unscrambler and confirming that there is no abnormal condition, stop the device, but the qualified infusion bottle upright in the bottle feeding bracket, and start the device again. The bottle will pass through the rotating carousel of the device and enter the conveyor belt to start the bottle unscramble operation. Run at low speed when starting up, and then adjust the lifting speed and unscramble speed according to the actual production, so that the speed of the Bottle Unscrambler equipment can match the actual production speed. To prevent such phenomena from happening. If such a phenomenon occurs, stop the machine immediately to eliminate the fault before it can continue to run. During the operation of the equipment, the bottles should be put in continuously, and observe whether there are phenomena such as pouring, jamming, broken bottles, etc. If any, stop the machine immediately and start the production after troubleshooting. After the production is over, stop the equipment, turn off the power of the Bottle Unscrambler, and clear the remaining materials out of the equipment.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. When the Liquid Filling Machine leaves the factory, it will provide customers with detailed Liquid Filling Machine operation procedures and operating specifications. If you are interested in Liquid Filling Machine, you can contact us, our website is www.cnzpack.com.
Korea East Asia Pharmaceutical Company, ordered a syrup filling line from our company, from bottle management - bottle washing - filling - corking - capping - labeling, the whole line in the Korean factory to complete the commissioning task, the whole line production design speed of 120 bottles per minute high-speed filling line.
In our production and life, the Cartoning Machine is of great significance to us, but sometimes, the Cartoning Machine will fail, so what is the reason for the failure of the Cartoning Machine? Next, let us analyze it together.
This is the content list:
Stop or stop between conveyor belts
The carton cannot be sucked down
The carton is not formed or ejected at the mouth of the box feeding template after being sucked
Can't suck the instructions
The paper rebounds during the suction process of the manual
The manual does not fold well
Uneven folding of the manual
There are curls and creases after the manual is folded
Manual stuck in the fence
1. Cartoning Machine shuts down at intervals to check if there is a shortage of materials and automatically starts up when supplemented.
2. Shut down the Cartoning Machine to check whether the power supply including the power supply part, the motor, or the governor is normal.
1. Whether the cartons of Cartons Machine are arranged neatly.
2. Whether the cartons of the Cartoning Machine are pasted together.
3. Whether the air pressure of the Cartoning Machine suction head is normal.
1. Check if the cartons of Cartons Machine are too hard.
2. Check whether the position of the guide rod of the cartons placed by the Cartoning Machine and the box delivery template are not correct.
3. Check whether the small hook spring at the rear of the Cartoning Machine delivery template is deformed.
4. Check if the height of the suction head of the Cartoning Machine and the box delivery track is correct.
1. Whether the Cartoning Machine manual is deformed, causing the suction head to fail to suck.
2. Whether the suction head gas of the Cartoning Machine is parallel to the manual.
3. Whether the paper width of the Cartoning Machine manual is different, the error must be within 1mm. The stacking position of the manual should be adjusted to a difference of 0.5mm from the inner edge when the suction head rises to the high position.
4. The small paper-separating hook above the suction head of the Cartoning Machine origami moves too early. Generally, the small hook should be inserted into the gap between the paper and the paper before the suction head is about to drop. The height of the small hook is adjusted to be 0.5mm away from the suction head when it is in the high position.
1. The foot-lifting action of the Cartoning Machine's manual was too early, and the manual was taken away by the foot support before being pulled down. The position of the feet of the Cartoning Machine is so that it does not touch the sucked manual when it is returned and it returns to the high position when the paper picking notch wheel has not pulled the paper.
2. Whether the matching speed of the Cartoning Machine suction head and paper picking wheel is the same. The suction head of the Cartoning Machine should be lowered first, and then the front part of the paper picking notch wheel should be pressed onto the paper.
1. Check if the Cartoning Machine paper is deformed and bent, and if there are burrs.
2. Is there any foreign matter in the fence of the Cartoning Machine blocking the paper?
3. The gap between the opening of the Cartoning Machine fence and the folding stick is too large, causing the paper to come out.
4. Is the gap between Cartons Machine's folding sticks too large to hold the paper? Adjust the adjusting screws at both ends of the folding stick to reduce the gap. If the Cartoning Machine folding stick has been used for too long and worn out, the folding stick must be replaced.
Check the Cartoning Machine to adjust the front and rear positions of the barriers in the fence to achieve the required folding size.
1. Is the gap between the Cartoning Machine baffle and the folding stick too large? Adjust the middle position of the baffle and folding stick.
2. If the middle position of the Cartoning Machine baffle and the folding stick has been adjusted, and there is still a large gap, remove the positioning pins on the Cartoning Machine baffle and re-adjust until the gap does not feed paper.
1. Whether the paper feeding gap of Cartoning Machine folding stick is too large and paper feeding is weak. The adjustment method is the same as above.
2. The installation position of the lower half of the Cartoning Machine fence is too long than the arc guide plate on it so that the paper cannot enter the folding stick below. Loosen all the fixing screws on the Cartoning Machine fence and adjust the board backward, but it should not be shorter than the upper guide plate and should be 1-3 mm longer than the guide plate. If it is shorter than the guide plate, the Cartoning Machine manual may go directly into the folding stick below without folding.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It will conduct a large number of tests before the Cartoning Machine leaves the factory to reduce the failure of the Cartoning Machine and provide warranty services. If you are interested in the Cartoning Machine, you can contact us Contact, our website is www.cnzpack.com.
The tube Filling machine And the Sealing machine are determined by multiple parameters. It is impossible to describe a Tube Filling machine And Sealing machine with any single parameter. Shaft power, blade displacement, pressure head, blade diameter, and filling speed are the five basic parameters that describe a Tube Filling Machine And Sealing machine. So, let's take a look at the principle of the Tube Filling machine And Sealing machine together. Here are some answers.
Here is the content list:
l Basic parameters.
l The shear rate of the fluid.
l Small slot and big slot.
The displacement of the blade is proportional to the flow rate of the blade itself, the first power of the blade speed, and the third power of the blade diameter. The shaft power consumed by the filling is proportional to the specific gravity of the fluid, the power standard of the blade itself, the third power of the speed, and the fifth power of the blade diameter. In the case of a certain power and blade form, the blade displacement and pressure head can be adjusted by changing the diameter of the blade and the matching of the speed. That is, the large diameter blade is equipped with a low-speed Tube Filling machine And a Sealing machine. High flow effect and low-pressure head, while the small diameter blade with high speed produces a higher pressure head and lower flow effect.
The shear rate of the fluid.
In the filling tank, the only way to make the micelles collide with each other is to provide a sufficient shear rate. According to the mechanism of the Tube Filling Machine And Sealing machine, it is because of the existence of fluid velocity difference that the fluid layers are mixed. Therefore, where the filling process always involves the fluid shear rate lhhaha620. Shear stress is a force that is the real cause of bubble dispersion and droplet breaking in filling applications. It must be pointed out that the shear rate at each point of the fluid in the entire stirred tank is not the same.
Small slot and big slot.
Experimental research shows that, as far as the blade area is concerned, no matter what type of blade, when the diameter of the blade is constant, the maximum shear rate and the average shear rate increase with the increase of the speed. However, when the rotation speed is constant, the relationship between the maximum shear rate and the average shear rate, and the diameter of the blade is related to the slurry type. When the rotation speed is constant, the maximum shear rate of the radial blade increases with the increase of the blade diameter, and the average shear rate has nothing to do with the diameter of the blade. These concepts about the shear rate of the blade area require special care in the design of the Tube Filling Machine And Sealing machine to reduce and enlarge. Because the small groove is compared with the large groove, the small groove Tube Filling Machine and Sealing machine often has the characteristics of high speed, small blade diameter, and low tip speed. The large groove Tube Filling Machine And Sealing machine often has the characteristics of low speed, large blade diameter, and high tip speed.
Our official website is https:// www.cnzpack.com/. If you are engaged in work related to the Tube Filling machine And Sealing machine, you can communicate with us on the website.
In our production and life, the Liquid Filling Machine has a significant impact on many industries, so what is the method of using the Liquid Filling Machine? Let's go take a look next.
This is the content list:
l The ground wire must be well-grounded before the Liquid Filling Machine works
l Liquid Filling Machine liquid filling system assembly
The ground wire must be well-grounded before the Liquid Filling Machine works.
The ground wire must be well-grounded before the Liquid Filling Machine works, and then the appropriate standard syringe must be selected according to the different filling volumes. Generally, a 1ml syringe is used when the dispensing range is 0.2-1ml. Use a 5ml syringe for 1-5ml.use a 10ml syringe for 5-10ml. The 20ml model uses a 20ml glass infusion device. The 100ml model uses a 100ml glass infusion device, and the 500ml model uses the stainless steel filling system produced by our factory.
Liquid Filling Machine liquid filling system assembly
Pull out the inner core of the Liquid Filling Machine syringe, put the screw sleeve on the inner core of the syringe, and use the screw sleeve to properly fasten it to the lower base (cleanliness must be paid when disassembling the syringe). Place the upper clamp seat on the outlet end of the Liquid Filling Machine syringe jacket, and properly tighten the nuts on both sides to assemble the inner core and outer jacket of the installed Liquid Filling Machine syringe into one body. At this point, the Liquid Filling Machine injection system is assembled.
Place the Liquid Filling Machine valve with the arrow facing upwards and the arrow mark facing outwards and fix it on the fixing screw with a nut. Assemble the Liquid Filling Machine with a complete liquid filling system, align the upper and lower round holes of the liquid filling system components with the upper and lower fixing rods respectively, and put them on the bearing so that the outer end surface and the bearing surface are levels. When assembling the lower end, do not make the screw sleeve and the crank touch to prevent abnormal noise when the crank on the Liquid Filling Machine rotates (the screw sleeve and the crank are about 1mm apart when installed correctly). After the liquid filling system is installed correctly, tighten it. Tighten the screws up and down. Use a short hose to connect the Liquid Filling Machine syringe to the valve connection nozzle. The liquid inlet pipe is connected to the water inlet, and the liquid outlet pipe is connected to the water outlet. To prevent the liquid inlet and outlet pipes from being entangled, clip the liquid inlet and outlet pipes into the ear openings on the side of the casing.
Turn the crank of the Liquid Filling Machine by hand, it should be able to rotate freely, otherwise, the assembly is wrong, you should check whether the Liquid Filling Machine injection system is fastened to the rotating bearing.
Our company has obtained more than 20 invention patents and utility model patents. The main products are a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and online capping machine, capping machine and labeling machine, bottle unscrambler, tube filling and sealing machine, Cartoning machines, and other packaging equipment. If you are interested in Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.
Wenzhou Zungwan Intelligent Machine Co.,Ltd. is the professional equipment manufacturer to keep researching and developing the packing machinery for every type of liquid, powder, cream/ointment, fluid and half-fluid etc. materials. We have Obtained ISO9001 quality management system authentication and parts of our products have passed CE authentication. Our company has obtained more than 20 invention patents and utility model patents. The main products range from nail polish filling machine, perfume machine,perfume filling machine, powder serial automatically volume-measuring packing machine and inline capping machine, rotary capping machine and labeling machine, bottle unscrambler , screw capping machine ,tube filling and sealing machine, cartoning machine and other Packaging equipments.
So far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and our service as well as our integrity is acclaimed both in China and abroad. we will carry forward the spirit of "integrated innovation, and perseverance," discipline ourselves to be the first, and provide better and more perfect service for our new and old customers with enthusiasm and a new attitude.
Tube Filling machine And Sealing machine is suitable for filling all kinds of paste and high viscosity fluids, suitable for filling large-diameter plastic pipes and composite pipes, and then the pipe is heated inside, and the batch number and date are printed on the seal. Used in pharmaceutical, food, cosmetics, adhesive, and other industries. Next, let me tell you about the related introduction and features of the Tube Filling machine And Sealing machine. Here are some answers.
Here is the content list:
l The related introduction of Tube Filling machine And Sealing machine.
l Design features of Tube Filling machine And Sealing machine.
l Features of Tube Filling machine And Sealing machine.
The related introduction of Tube Filling machine And Sealing machine.
Tube Filling machine And Sealing machine is a machine that fills the packaging into the container and seals it. After the product is put into the packaging container, to keep the product sealed, maintain product quality, and avoid product loss, the packaging container needs to be sealed. Tube Filling machine And Sealing machine is a machine with a compact design and automatic tube feeding. Tube Filling machine And Sealing machine's tube washing, feeding marking, filling, folding, sealing, coding, and finished product output are all performed by a fully automatic control system. The feeding of the washing pipe adopts a pneumatic method, which is accurate and reliable.
Design features of Tube Filling machine And Sealing machine.
First, the Tube Filling machine And Sealing machine is mechatronics, using multiple-introduction technology, controlled by PLC, and can automatically complete tube feeding, partial color labeling, filling, sealing, and tube outlet at the same time. The machine runs smoothly, is easy to control and size conversion, and is suitable for the production of pasty products. Second, the Tube Filling Machine And the Sealing machine has modern modeling, strong practicability, and high processing value. Third, the Tube Filling Machine And the Sealing machine have a stainless steel volumetric bulldozing syringe and a Teflon piston seal to achieve accurate dosage.
Features of Tube Filling machine And Sealing machine.
Tube Filling machine And Sealing machine is a piece of high-tech equipment successfully developed by introducing foreign advanced technology and combining GMP requirements. It has the characteristics of reasonable structure, complete functions, convenient operation, accurate filling, stable operation, and low noise. Tube Filling machine And Sealing machine adopts PLC controller, from liquid or high-speed material filling to batch number printing (including production date) automatic operation, is cosmetics, pharmaceuticals, food, adhesives and other ALU tubes, plastic tubes and multi-tube filling Ideal equipment for sealing, in line with GMP standards.
Wenzhou Zungwan Intelligent Machine Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream, ointment, fluid, and semi-fluid materials. If you are engaged in work related to Tube Filling machine And Sealing machine or want to know more about our company, you can communicate with us on the website. Our official website is https:// www.cnzpack.com/. Our company adheres to the service tenet of "customer first", and implements the service of honesty and customer first.