Oil Filling and Corking machine supplier- China Factory Manufacturers Suppliers

The Cosmetic Filling Machine and Capping machine is a professional cosmetic filling and capping equipment, which can make the cap tighter without damaging the mouth of the bottle and effectively protect the cosmetics from contact with the outside world. Next, let's take a look at the use and maintenance of the Cosmetic Filling machine and the capping machine. Here are some answers.

Here is the content list:

l Instructions for use of Cosmetic Filling machine And Capping machine.

l How is the daily maintenance of the Cosmetic Filling machine And Capping machine?

Instructions for use of Cosmetic Filling machine And Capping machine.

First, because the Cosmetic Filling Machine and Capping machine is an automated machine, the dimensions of the pop-up bottle, bottle liner, and bottle cap are required to be uniform. Second, before driving, you must first use the crank handle to turn the machine to see if there is any abnormality in the rotation, and then you can drive after it is confirmed that it is normal. Third, when adjusting the machine, the tools should be used appropriately. It is strictly forbidden to use excessive tools or excessive force to dismantle the parts to avoid damage to the machine parts or affect the performance of the machine. Fourth, the Cosmetic Filling machine and the Capping machine must be kept clean. Before the shift, all parts of the machine surface should be cleaned once, and clean lubricating oil should be added to each activity department. It should be scrubbed once a week, especially the areas that are not easily cleaned in normal use or blown with compressed air.

How is the daily maintenance of the Cosmetic Filling machine And Capping machine?

First, the Cosmetic Filling Machine and the Capping machine has strict requirements for the placement environment and must ensure the indoor humidity is moderate, ventilated, and hygienic. Because the Cosmetic Filling Machine and Capping machine is a mechanical device, after all, the raw materials are some steel electromechanical, etc. It is easy to rust when placed in a humid environment, and a closed environment is not conducive to the heat dissipation of the equipment during operation. Second, you must ensure that the power supply is normal and the grounding wire is safe before use. Voltage instability can cause considerable damage to the machine. Third, the non-woven soft cloth and cleaning agent must be added to wipe off the oil or dirt and wipe dry before the Cosmetic Filling machine and capping machine are operated. After use, take out all the remaining materials to prevent the materials from corroding the equipment and scrub them clean. Periodically clean the invisible dust and garbage in the chassis. And adhere to the tightness of the mechanical parts. Fourth, clean up the machine regularly. Many companies conduct major maintenance on machinery and equipment once a year in autumn. Fifth, add lubricating oil to the mechanical components of the Cosmetic Filling machine and Capping machine regularly to reduce frictional resistance and make the machine run faster.

Our official website is https:// www.cnzpack.com/. If you are engaged in work related to Cosmetic Filling machines and Capping machines or want to learn more about our company, you can communicate with us on the website.

In our production and life, the Liquid Filling Machine has a significant impact on many industries, so what is the method of using the Liquid Filling Machine? Let's go take a look next.

This is the content list:

l The ground wire must be well-grounded before the Liquid Filling Machine works

l Liquid Filling Machine liquid filling system assembly

The ground wire must be well-grounded before the Liquid Filling Machine works.

The ground wire must be well-grounded before the Liquid Filling Machine works, and then the appropriate standard syringe must be selected according to the different filling volumes. Generally, a 1ml syringe is used when the dispensing range is 0.2-1ml. Use a 5ml syringe for 1-5ml.use a 10ml syringe for 5-10ml. The 20ml model uses a 20ml glass infusion device. The 100ml model uses a 100ml glass infusion device, and the 500ml model uses the stainless steel filling system produced by our factory.

Liquid Filling Machine liquid filling system assembly　　

Pull out the inner core of the Liquid Filling Machine syringe, put the screw sleeve on the inner core of the syringe, and use the screw sleeve to properly fasten it to the lower base (cleanliness must be paid when disassembling the syringe). Place the upper clamp seat on the outlet end of the Liquid Filling Machine syringe jacket, and properly tighten the nuts on both sides to assemble the inner core and outer jacket of the installed Liquid Filling Machine syringe into one body. At this point, the Liquid Filling Machine injection system is assembled.

Place the Liquid Filling Machine valve with the arrow facing upwards and the arrow mark facing outwards and fix it on the fixing screw with a nut. Assemble the Liquid Filling Machine with a complete liquid filling system, align the upper and lower round holes of the liquid filling system components with the upper and lower fixing rods respectively, and put them on the bearing so that the outer end surface and the bearing surface are levels. When assembling the lower end, do not make the screw sleeve and the crank touch to prevent abnormal noise when the crank on the Liquid Filling Machine rotates (the screw sleeve and the crank are about 1mm apart when installed correctly). After the liquid filling system is installed correctly, tighten it. Tighten the screws up and down. Use a short hose to connect the Liquid Filling Machine syringe to the valve connection nozzle. The liquid inlet pipe is connected to the water inlet, and the liquid outlet pipe is connected to the water outlet. To prevent the liquid inlet and outlet pipes from being entangled, clip the liquid inlet and outlet pipes into the ear openings on the side of the casing.

Turn the crank of the Liquid Filling Machine by hand, it should be able to rotate freely, otherwise, the assembly is wrong, you should check whether the Liquid Filling Machine injection system is fastened to the rotating bearing.

Our company has obtained more than 20 invention patents and utility model patents. The main products are a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and online capping machine, capping machine and labeling machine, bottle unscrambler, tube filling and sealing machine, Cartoning machines, and other packaging equipment. If you are interested in Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.

Wenzhou Zungwan Intelligent Machine Co.,Ltd. is the professional equipment manufacturer to keep researching and developing the packing machinery for every type of liquid, powder, cream/ointment, fluid and half-fluid etc. materials. We have Obtained ISO9001 quality management system authentication and parts of our products have passed CE authentication. Our company has obtained more than 20 invention patents and utility model patents. The main products range from nail polish filling machine, perfume machine,perfume filling machine, powder serial automatically volume-measuring packing machine and inline capping machine, rotary capping machine and labeling machine, bottle unscrambler , screw capping machine ,tube filling and sealing machine, cartoning machine and other Packaging equipments.

So far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and our service as well as our integrity is acclaimed both in China and abroad. we will carry forward the spirit of "integrated innovation, and perseverance," discipline ourselves to be the first, and provide better and more perfect service for our new and old customers with enthusiasm and a new attitude.

Liquid Filling Machine is used in the beverage, drinking water, and liquor industries and has become a very important equipment in the liquid food industry. function. So what are the main structural designs of Liquid Filling Machine? Let's take a look at it together.

This is the content list:

l The transmission system of Liquid Filling Machine

l Liquid Filling Machine's actuator

l Liquid Filling Machine's control system

l The body part of the Liquid Filling Machine

The transmission system of Liquid Filling Machine

Liquid Filling Machine's transmission system, this part is to transmit power and motion to various actuators, control elements, and auxiliary mechanisms. Liquid Filling Machine's main transmission components include gears, sprockets, worm gears, screws, and nuts, etc.

Liquid Filling Machine's actuator

Liquid Filling Machine's actuator, this part is mainly to achieve the Liquid Filling Machine packaging process operation and auxiliary operation part, packaging process operation refers to filling, auxiliary operation part refers to packaging materials and products supply and delivery, Liquid Filling Machine packaging material output, etc., the actuator is the core of the machine, its action sequence, and movement law according to the process principle and requirements.

Liquid Filling Machine's control system

The control system of the Liquid Filling Machine is to control the relevant parts of the Liquid Filling Machine, allocate the movements to the actuators, and make them coordinate the movements according to the time and sequence, thus realizing the process functions of the Liquid Filling Machine.

The body part of the Liquid Filling Machine

The body of the Liquid Filling Machine is the skeleton of the Liquid Filling Machine, which mainly plays the role of supporting and positioning the parts. The stability of the body is the first consideration in the design, and the center of gravity of the Liquid Filling Machine should be lowered as much as possible to make the Liquid Filling Machine work smoothly.

The mainframe of Liquid Filling Machine is to fix and support all the working actuators, transmission parts, control systems, to ensure their relative position correctness and stability. The vacuum system of the Liquid Filling Machine sucks the air out of the bottle, thus generating negative pressure inside the bottle, the liquid is filled into the bottle from the liquid tank through the liquid supply system and the filling head, when the liquid reaches the required liquid level, the inlet port is closed and the suction port sucks the excess liquid and foam away.

Liquid Filling Machine of Wenzhou Zungwan Intelligent Machinery Co., Ltd. is first-class product quality and efficient and fast after-sales service, which has created the excellent products of "Zhonghuan". To meet the market demand of Liquid Filling Machine is our eternal topic and sincere commitment to our customers. If you are interested in Liquid Filling Machine, please contact us, our website is www.cnzpack.com. We will carry forward the spirit of "comprehensive innovation, perseverance", self-discipline and strive to be the first, with enthusiasm, new attitude to provide new and old customers with more perfect service. We are looking forward to cooperating with you.

With the increasingly fierce competition in the manufacturing and production of plastic bottles in the food and pharmaceutical industries, Bottle Unscrambler has become more and more solid backing for the food and pharmaceutical plastic bottle markets. So how does it play a role? We will introduce the work process and personnel operation specifications of Bottle Unscrambler. Let's take a look together next.

This is the content list:

• The workflow of Bottle Unscrambler

• Personnel operation specification of Bottle Unscrambler

The workflow of Bottle Unscrambler

The workflow of Bottle Unscrambler is generally as follows: manually put materials into the storage bottle library, the materials in the storage bottle library will be automatically quantified and fed to the turntable at the set speed. The turntable rotates at a high speed to supply the bottles as required, the web wheel The irregular bottles are removed, and the bottle dividing part sends the bottles from the turntable to the bottle unscramble part at a certain speed. The Bottle Unscrambler part of the Bottle Unscrambler clamps the bottles to the working surface of the conveyor through the conveyor belts on both sides, and at the same time sorts the bottles through the bottle turner. The Bottle Unscrambler electronic control system performs real-time monitoring and feedback through the sensors of each part to achieve fully automated operation requirements, and save a lot of labor costs and avoid losses caused by human error factors.

Personnel operation specification of Bottle Unscrambler

To ensure the normal and safe operation of Bottle Unscrambler, there are special operating procedures established for it. Operators and equipment management personnel shall perform standardized operations of Bottle Unscrambler under these procedures. This safe operation specification is commonly used in Bottle Unscramblers, mixers, high-speed automatic Bottle Unscramblers, etc.

1. First check the Bottle Unscrambler's intact, clean, and expiration status identification and the equipment operation record of the shift. If the inspection finds that the Bottle Unscrambler has exceeded the cleaning validity period, it is necessary to further clean the equipment according to the equipment cleaning operation rules and fill in the equipment status identification.

2. Check the Bottle Unscrambler and the Bottle Unscrambler to confirm that there is no foreign matter, and turn the bottle plate and unscrambler to confirm that it can work normally.

3. Turn on the Bottle Unscrambler power switch, check the touch screen and three photoelectric switches. If both are energized, the lack of a bottle alarm will be displayed on the touch screen. When the electric eye is blocked by hand, the screen displays the blocking alarm, and the two photoelectric switches are in a normal state.

4. Turn on the Bottle Unscrambler compressed air, use the bottom of the bottle to shake under the electric eye of the bottle puller, compressed air will be sprayed out, and the equipment can be turned on normally.

To ensure that the various parts of the Bottle Unscrambler can work normally, the formal operation can be divided into five steps: click the host start and lift start on the touch screen respectively, and observe whether the Bottle Unscrambler has abnormal noise when it is running. After powering on the Bottle Unscrambler and confirming that there is no abnormal condition, stop the device, but the qualified infusion bottle upright in the bottle feeding bracket, and start the device again. The bottle will pass through the rotating carousel of the device and enter the conveyor belt to start the bottle unscramble operation. Run at low speed when starting up, and then adjust the lifting speed and unscramble speed according to the actual production, so that the speed of the Bottle Unscrambler equipment can match the actual production speed. To prevent such phenomena from happening. If such a phenomenon occurs, stop the machine immediately to eliminate the fault before it can continue to run. During the operation of the equipment, the bottles should be put in continuously, and observe whether there are phenomena such as pouring, jamming, broken bottles, etc. If any, stop the machine immediately and start the production after troubleshooting. After the production is over, stop the equipment, turn off the power of the Bottle Unscrambler, and clear the remaining materials out of the equipment.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. When the Liquid Filling Machine leaves the factory, it will provide customers with detailed Liquid Filling Machine operation procedures and operating specifications. If you are interested in Liquid Filling Machine, you can contact us, our website is www.cnzpack.com.

Korea East Asia Pharmaceutical Company, ordered a syrup filling line from our company, from bottle management - bottle washing - filling - corking - capping - labeling, the whole line in the Korean factory to complete the commissioning task, the whole line production design speed of 120 bottles per minute high-speed filling line.

Liquid Filling Machine is specially designed for filling easy-to-open bottles. It has a reasonable design, simple structure, easy operation, and a mechanical bottle stop filling device. So what is the working principle of a Liquid Filling Machine? Let's take a look together next.

This is the content list:

l Transmission principle of Liquid Filling Machine

l The principle of the filling part of the Liquid Filling Machine

l Liquid Filling Machine's capping system

l The capping head of the Liquid Filling Machine

l The Liquid Filling Machine's tracking and filling mechanism

Transmission principle of Liquid Filling Machine

The Liquid Filling Machine transmits the power to the worm gear shaft of the reducer through the belt pulley, and then the worm gear shaft transmits the power to the paddlewheel shaft, the filling part, and the capping head through each gear. the filling part, the capping head, and each paddle wheel of the Liquid Filling Machine move synchronously, and the power is transmitted to the bottle feeding paddle wheel device through the bevel gear.

The principle of the filling part of the Liquid Filling Machine

The liquid bottle of the Liquid Filling Machine is sent to the transition pulley by the large bottle inlet paddlewheel and then sent to the synchronous belt by the transition pulley. The bottle is dragged forward at a uniform speed by the inserts on the synchronous belt, and the filling needle of the Liquid Filling Machine is inserted into the bottle mouth under the control of the tracking mechanism and runs forward synchronously with the bottle to achieve tracking and filling. The diving needle rises with the liquid level to play the role of defoaming.

Liquid Filling Machine's cap supply system

The cap supply system of the Liquid Filling Machine is composed of a cap delivery track, cap handling head, and cap-wearing mechanism. The lid management head adopts the principle of electromagnetic spiral oscillation to line up the messy lids and enter the lid delivery track through the reversing twist channel. When the Liquid Filling Machine passes through the lid-wearing mechanism, the bottle hangs on to the lid and passes through the pressure plate to make the lid wear correctly.

The capping head of the Liquid Filling Machine

After the liquid bottle of Liquid Filling Machine enters the cap rolling head turntable with the cap on, the three rolling knives which have been opened will turn forward with the Liquid Filling Machine turntable with the bottle as the center and press the cap under the control of the cam, then the three rolling knives will roll towards the cap at the same time under the action of the cone sleeve, and after rolling, they will leave the cap at the same time and return to the original position.

Liquid Filling Machine's tracking and filling mechanism

The Liquid Filling Machine drives the gear and rack to move, thus driving the filling needle to do the reciprocating movement. By adjusting the relative position of the Liquid Filling Machine's syringe holder and mounting frame, the filling needle can be accurately inserted into the middle of the bottle opening.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, and so far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and services as well as our integrity are widely praised at home and abroad. We will carry forward the spirit of "comprehensive innovation, perseverance", self-discipline and strive for the first, with enthusiasm and a new attitude to provide more perfect service for new and old customers. If you are interested in Liquid Filling Machine, please contact us, our website is www.cnzpack.com

Pharmaceutical Filler and Capper, whether semi-automatic or fully automatic, will encounter more or less in the process of using different places of failure, in the face of Pharmaceutical Filler and Capper's special parts of the failure, how do we find the problem as soon as possible and solve it? Let's take a look at it.

This is the content list:

l Pharmaceutical Filler and Capper's PLC failure

l Pharmaceutical Filler and Capper's Magnetic Switch Failure

l Pharmaceutical Filler and Capper solenoid valve failure

Pharmaceutical Filler and Capper PLC Failure

If the point controls Pharmaceutical Filler and Capper, the fault phenomenon is that the motor runs after the signal start Pharmaceutical Filler and Capper, but the motor does not stop running after the stop signal is issued. And Capper only stops running when the PLC is powered down. If the point controls the solenoid valve. The fault phenomenon is that the solenoid valve coil is not energized, and the cylinder is not reset. If the PLC of Pharmaceutical Filler and Capper is hit with external force to make the sticking point separate, it can assist to determine the fault of Pharmaceutical Filler and Capper.

Pharmaceutical Filler and Capper's magnetic switch failure

Pharmaceutical Filler and Capper's magnetic switch is used to detecting the position of the cylinder and control the cylinder travel. The four cylinders of laminating, pushing, pressing, and fusing knife are interrelated, and the magnetic switch is used to detect and control their positions. Pharmaceutical Filler and Capper failure is mainly manifested as the subsequent cylinders do not move, because the cylinder speed of Pharmaceutical Filler and Capper is faster, which causes the magnetic switch cannot detect the signal. Such as pushing the package cylinder speed is too fast, after pushing the package reset, the pressure package and fusion knife cylinder do not move.

Solenoid valve failure of Pharmaceutical Filler and Capper

Pharmaceutical Filler and Capper solenoid valve failure is mainly manifested as the cylinder does not move or does not reset, the reason is that Pharmaceutical Filler and Capper cylinder solenoid valve cannot change direction or tampering air. If the solenoid valve falters, the air pressure of Pharmaceutical Filler and Capper can't reach the working pressure because the inlet and outlet air paths are connected, and the knife beam doesn't rise to the place. the proximity switch of Pharmaceutical Filler and Capper knife beam protection doesn't work, and the precondition of full machine operation is not established. Pharmaceutical Filler and Capper does not operate, which is easily confused with an electrical fault. Solenoid valve air leakage sound, listen carefully to the source of sound and hand search for air leakage points, generally can easily identify the air leakage solenoid valve.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, with first-class product quality and efficient and fast after-sales service, forging the excellent products of "Central". Pharmaceutical Filler and Capper will undergo a lot of product testing before leaving the factory to reduce the probability of failure of Pharmaceutical Filler and Capper, and also provide customers with high-quality Pharmaceutical Filler and Capper warranty service. If you are interested in Pharmaceutical Filler and Capper, you can contact us, our website is www.cnzpack.com.

14 Station Stainless Steel Rotary Piston Filler Used Customized 14 Station Piston Filler with: Currently set to run a 404 can size Output: 50 to 300 containers per minute depending on application and materials 4.5 inch wide table top conveyor with timing... Elmar RPC-21-IRH 21 Station Rotary Piston Filler

Labeling Machine - Devikrupa Industries The Labeling machine is a machine or equipment which applies, dispenses or prints different kind of labels on a wide range of products, Bottle, containers, packages, boxes etc. many more. This is known as labeling machine.

Machinery Packaging Machines Filling Machines Wholesale cream filling sealing capping machine. Cream Filling Sealing Capping Machine (3181 products available)

The structure of sleeve applicator and conveyor are made of SS 304 and the structure of tunnel is made from MS with powder coating. Rigid vibration free construction for trouble free performance. The SS 304 slat conveyor for proper product conveying. (For the processes of sleeve inserting and sleeve shrinking. Worm for the positive feeding.

Automatic Cartoning Machine Rs 11 Lakh / Piece Get Best Price Beware from Duplication and cheater. Nobody our Ex-partnerMachine design copyright by sohamtex engineers. Production: …

Automatic bag-given doypack packing machine Liquid and paste Packaging Machine Certification: CE Place of Origin: CHINA MOQ: 1 Payment Terms: L/C, T/T Supply Ability: 50 SET/MONTH Packaging Details: Wooden Model: ZG8-300L Working position: ...

Double Head Weigh Filler Packaging Machine 10 gm to 1 kg Single Head Weigh Filler Packaging Machine 10 gm to 2 kg Double Head Weigh Filler Packaging Machine 10 gm to 2 kg Double Head Weigh Filler Four Head Weigh Filler Cup Filler Packaging Machine 5 gm to 50 gm Auger Filler Packaging Machine For Powders 5 gm to 200 gm

Find 2022 quality