rotary filling and capping machine- China Suppliers Manufacturers Factory

In our production and life, the Liquid Filling Machine has a significant impact on many industries, so what is the method of using the Liquid Filling Machine? Let's go take a look next.

This is the content list:

l The ground wire must be well-grounded before the Liquid Filling Machine works

l Liquid Filling Machine liquid filling system assembly

The ground wire must be well-grounded before the Liquid Filling Machine works.

The ground wire must be well-grounded before the Liquid Filling Machine works, and then the appropriate standard syringe must be selected according to the different filling volumes. Generally, a 1ml syringe is used when the dispensing range is 0.2-1ml. Use a 5ml syringe for 1-5ml.use a 10ml syringe for 5-10ml. The 20ml model uses a 20ml glass infusion device. The 100ml model uses a 100ml glass infusion device, and the 500ml model uses the stainless steel filling system produced by our factory.

Liquid Filling Machine liquid filling system assembly　　

Pull out the inner core of the Liquid Filling Machine syringe, put the screw sleeve on the inner core of the syringe, and use the screw sleeve to properly fasten it to the lower base (cleanliness must be paid when disassembling the syringe). Place the upper clamp seat on the outlet end of the Liquid Filling Machine syringe jacket, and properly tighten the nuts on both sides to assemble the inner core and outer jacket of the installed Liquid Filling Machine syringe into one body. At this point, the Liquid Filling Machine injection system is assembled.

Place the Liquid Filling Machine valve with the arrow facing upwards and the arrow mark facing outwards and fix it on the fixing screw with a nut. Assemble the Liquid Filling Machine with a complete liquid filling system, align the upper and lower round holes of the liquid filling system components with the upper and lower fixing rods respectively, and put them on the bearing so that the outer end surface and the bearing surface are levels. When assembling the lower end, do not make the screw sleeve and the crank touch to prevent abnormal noise when the crank on the Liquid Filling Machine rotates (the screw sleeve and the crank are about 1mm apart when installed correctly). After the liquid filling system is installed correctly, tighten it. Tighten the screws up and down. Use a short hose to connect the Liquid Filling Machine syringe to the valve connection nozzle. The liquid inlet pipe is connected to the water inlet, and the liquid outlet pipe is connected to the water outlet. To prevent the liquid inlet and outlet pipes from being entangled, clip the liquid inlet and outlet pipes into the ear openings on the side of the casing.

Turn the crank of the Liquid Filling Machine by hand, it should be able to rotate freely, otherwise, the assembly is wrong, you should check whether the Liquid Filling Machine injection system is fastened to the rotating bearing.

Our company has obtained more than 20 invention patents and utility model patents. The main products are a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and online capping machine, capping machine and labeling machine, bottle unscrambler, tube filling and sealing machine, Cartoning machines, and other packaging equipment. If you are interested in Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.

Due to the particularity of the environment in which the Liquid Filling Machine equipment is used, the structure of the metal itself is prone to corrosion. The external environment such as temperature, humidity, and air will directly cause the metal to corrode. After the Liquid Filling Machine equipment is corroded, the color, appearance, and basic performance of the machine may change, which causes damage to the machine equipment and also causes a waste of energy, causing the company to suffer a greater loss. To reduce the damage of the Liquid Filling Machine caused by corrosion, we should do anti-corrosion work during design, production, and later use. So what are the anti-corrosion methods of Liquid Filling Machines? Let's take a look together next.

This is the content list:

• Selection of Liquid Filling Machine materials

• Liquid Filling Machine structure and process

• Liquid Filling Machine corrosion inhibitor

Selection of Liquid Filling Machine materials

Most of the Liquid Filling Machine equipment materials used in the manufacturing industry are carbon steel. The price of this kind of steel is relatively low, and at the same time, it is more convenient to purchase and easy to process. Such steel will not cause major corrosion when used in the ordinary working environment, and will not cause major harm to the use of Liquid Filling Machine equipment. But if it is used in an enterprise, its working environment may cause serious erosion.

Liquid Filling Machine structure and process

If the collective shape design of the Liquid Filling Machine components is too complicated or unreasonable, it may cause defects such as thermal stress, dust accumulation, Liquid Filling Machine stress, and liquid accumulation, which may lead to corrosion in the connecting and unloading parts. From the perspective of anti-corrosion, comprehensive consideration is given to the design of the Liquid Filling Machine structure.

Liquid Filling Machine corrosion inhibitor

Liquid Filling Machine corrosion inhibitor is a chemical substance that is added to the corrosion inhibitor system at a proper concentration, which can significantly reduce the corrosion rate of the metal and has a small effect on the concentration of the corrosive agent. The amount of Liquid Filling Machine corrosion inhibitor is very small. Although it cannot change the corrosion tendency of the metal in the medium, it can form a protective film on the metal surface to slow down the corrosion rate of the metal, thereby reducing the corrosion of the metal.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. So far, we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and services as well as our integrity are widely praised at home and abroad. Before the Liquid Filling Machine leaves the factory, the corrosion resistance of the Liquid Filling Machine will be enhanced. If you are interested in the Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.

Capping Machine operation, accuracy error, installation adjustment, equipment cleaning, maintenance, and other aspects are very simple and convenient. Capping Machine has been widely used in various industries such as daily chemical and grease, and can fill different high-viscosity fluids. So what are the working principles and structural characteristics of the Capping Machine? Let's take a look together next.

This is the content list:

l How Capping Machine works

l Structural characteristics of Capping Machine

How Capping Machine works

The Capping Machine adopts a new horizontal design, which is light and convenient and can automatically pump the material. For thicker slurry, a hopper can be added. When the Capping Machine is in the "auto" state, the Capping Machine will automatically perform continuous filling at a set speed. Capping Machines can be divided into three types: atmospheric filling machine, vacuum filling machine, and pressure filling machine.

Under normal pressure, Capping Machine can fill the liquid in a self-flowing manner according to the weight of the liquid itself. The filling method is to fill at a pressure greater than atmospheric pressure. The pressure in the liquid storage tank is greater than the pressure in the bottle, and the liquid that needs to be filled will enter the bottle depending on the pressure difference. The key component of the Capping Machine is the PLC operation control system. Under normal pressure, Capping Machine can fill the liquid in a self-flowing manner according to the weight of the liquid itself. The filling method is to fill at a pressure greater than atmospheric pressure. The pressure in the liquid storage tank is greater than the pressure in the bottle, and the liquid that needs to be filled will enter the bottle depending on the pressure difference. The key component of the Capping Machine is the PLC operation control system.

The principle of the Capping Machine is relatively easy to understand. The improved control system simplifies the structure of the machine. It can be seen from the operating conditions and control efficacy tests of the actual application that the automation level of the system has reached the design requirements. This reduces the labor intensity of the operator and makes the production line that needs filling production about 30% higher than before, so the probability of failure of the Capping Machine is significantly reduced.

Structural characteristics of Capping Machine

The design of the Capping Machine is very reasonable and appropriate, the remainder of the machine is very small, and the operation and use are very simple. The pneumatic parts inside the Capping Machine all use new pneumatic components. The piston and cylinder of the Capping Machine cylinder are made of polytetrafluoroethylene and stainless steel to meet the requirements of GMP testing. The filling quantity and filling speed of the Capping Machine can be adjusted at will, and the degree is relatively high.

The Capping Machine can be modified according to actual production needs. It can be transformed into a multi-head system, explosion-proof system, and overflow system. The Capping Machine is suitable for use in food, daily necessities, pesticides, and other industries, and has a broad application prospect.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. The company strictly controls the quality of the Capping Machine. If you are interested in Capping Machine, you can contact us, our website is www.cnzpack.com. I look forward to your coming and hope to cooperate with you.

The tube Filling machine And the Sealing machine are determined by multiple parameters. It is impossible to describe a Tube Filling machine And Sealing machine with any single parameter. Shaft power, blade displacement, pressure head, blade diameter, and filling speed are the five basic parameters that describe a Tube Filling Machine And Sealing machine. So, let's take a look at the principle of the Tube Filling machine And Sealing machine together. Here are some answers.

Here is the content list:

l Basic parameters.

l The shear rate of the fluid.

l Small slot and big slot.

Basic parameters.

The displacement of the blade is proportional to the flow rate of the blade itself, the first power of the blade speed, and the third power of the blade diameter. The shaft power consumed by the filling is proportional to the specific gravity of the fluid, the power standard of the blade itself, the third power of the speed, and the fifth power of the blade diameter. In the case of a certain power and blade form, the blade displacement and pressure head can be adjusted by changing the diameter of the blade and the matching of the speed. That is, the large diameter blade is equipped with a low-speed Tube Filling machine And a Sealing machine. High flow effect and low-pressure head, while the small diameter blade with high speed produces a higher pressure head and lower flow effect.

The shear rate of the fluid.

In the filling tank, the only way to make the micelles collide with each other is to provide a sufficient shear rate. According to the mechanism of the Tube Filling Machine And Sealing machine, it is because of the existence of fluid velocity difference that the fluid layers are mixed. Therefore, where the filling process always involves the fluid shear rate lhhaha620. Shear stress is a force that is the real cause of bubble dispersion and droplet breaking in filling applications. It must be pointed out that the shear rate at each point of the fluid in the entire stirred tank is not the same.

Small slot and big slot.

Experimental research shows that, as far as the blade area is concerned, no matter what type of blade, when the diameter of the blade is constant, the maximum shear rate and the average shear rate increase with the increase of the speed. However, when the rotation speed is constant, the relationship between the maximum shear rate and the average shear rate, and the diameter of the blade is related to the slurry type. When the rotation speed is constant, the maximum shear rate of the radial blade increases with the increase of the blade diameter, and the average shear rate has nothing to do with the diameter of the blade. These concepts about the shear rate of the blade area require special care in the design of the Tube Filling Machine And Sealing machine to reduce and enlarge. Because the small groove is compared with the large groove, the small groove Tube Filling Machine and Sealing machine often has the characteristics of high speed, small blade diameter, and low tip speed. The large groove Tube Filling Machine And Sealing machine often has the characteristics of low speed, large blade diameter, and high tip speed.

Our official website is https:// www.cnzpack.com/. If you are engaged in work related to the Tube Filling machine And Sealing machine, you can communicate with us on the website.

Liquid Filling Machine is a kind of process machinery, its process characteristics are more obvious, for the design requirements provided by the customer as well as the functions, work efficiency and other aspects of good, then Liquid Filling Machine what are the design principles and considerations? Let's learn about it together.

This is the content list:

l The design principle of Liquid Filling Machine

l Precautions for Liquid Filling Machine

The design principle of Liquid Filling Machine

First, design the parameters of the Liquid Filling Machine and the material to be filled, and then also to understand the container to be filled, to understand the shape of the container and the characteristics of the container cap, according to these characteristics design the corresponding bottle Liquid Filling Machine.

Secondly, we should also know the functions to be achieved by the Liquid Filling Machine, the principle and method of Liquid Filling Machine filling, the whole process of Liquid Filling Machine filling should be carefully understood, and each link should be designed reasonably and appropriately to avoid affecting the effect of filling.

Liquid Filling Machine should also be based on the specific needs of enterprises, the use of functional principles of innovative design methods to design filling equipment to meet the production needs of enterprises, which will not only improve efficiency but also reduce the rate of damage and reduce the production costs of enterprises.

Precautions for Liquid Filling Machine

First, check the Liquid Filling Machine itself to determine if the ball valve in the filling machine is damaged or loose. If the internal ball valve of the Liquid Filling Machine is the cause, the solution is to replace the internal ball valve. If the internal ball valve of the Liquid Filling Machine is damaged, there is no way to repair it, only to replace it with a new one.

Check that the Liquid Filling Machine syringe assembly is clean. If it is not clean, it will cause an unclean blockage between the inner and outer tubes, so remove the Liquid Filling Machine syringe, clean it and disinfect and maintain it.

Check that the Liquid Filling Machine filler nozzle is complete. If the Liquid Filling Machine filling nozzle is damaged, the equipment will leak during operation. Replace broken filling nozzles and inspect other filling nozzles for use, deterioration, or corrosion, and replace them as soon as possible.

Check whether the O-ring is corroded or worn. If the O-ring is corroded or worn, it will also cause the Liquid Filling Machine to drip. Therefore, in this case, it is recommended to replace the O-ring.

Check the Liquid Filling Machine barrel position. Determine if the cylinder is in the cylinder center support position, and also check if the Liquid Filling Machine cylinder piston and piston rod are secure, and if they are loose, please lock them. If the cylinder failure position is changed, you need to reinstall the cylinder and confirm the correct position.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, which has made great achievements in Liquid Filling Machine and is loved by the consumers. If you are interested in Liquid Filling Machine, you can contact us, our website is www.cnzpack.com.

Celebrate the 10th anniversary of ZUNGWAN intelligent machine

——A letter from ZUNGWAN machine to you

Hello, partners, customers and friends of ZUNGWAN machine!

April 12 is the 10th anniversary of the establishment of ZUNGWAN intelligent machine. I'm 10 years old. From April 12, 2011 when I officially got my birth certificate (business license) to today, I've accompanied my close partners and colleagues through 10 spring, summer, autumn and winter, 10 special birthdays, and cooperated with more than 200 large, medium and small enterprises, companies and factories at home and abroad, It has sold more than 2000 automatic filling and sealing machines, more than 1000 automatic filling and capping machines, more than 3000 semi-automatic filling machines and more than 500 filling and packaging production lines.

My name is Wenzhou ZUNGWAN Intelligent Machine Co., Ltd. now has more than 50 employees. I am a well-known brand enterprise specializing in the R & D, production and sales of hose filling and sealing machine, aluminum tube filling and folding machine, various material filling and capping machine, full-automatic linear filling machine, capping machine, labeling machine, water cream filling and capping machine and other related packaging machinery and equipment supporting products, It has a complete and scientific quality management system. The enterprise integrity, company strength and product quality of ZUNGWAN Intelligent Machine have won the full support, trust and recognition of customers and friends at home and abroad.

Since the establishment of the company in 2011, our main sales and production staff have worked in the packaging machinery industry for more than 5 years. They have rich experience in R & D, production, sales and after-sales of cosmetics, skin care products and drug packaging production equipment. After successfully completing hundreds of enterprise order projects, Further promote our strategic sales of machinery and improve after-sales tracking service. In the next development period of the enterprise, it will participate more in the cooperation with famous brand companies, have a close relationship with cosmetics, skin care products, drugs and food enterprises, and create new brilliance in central machinery design, innovation and breakthrough with more like-minded people.

By combining the production technical strength of both supply and demand sides and using advanced machine professional knowledge, since 2011, we have been engaged in the sales of packaging machinery industry for more than 15 years. The chief engineer of filling and sealing machine production workshop, Potter and director Wu, who has been engaged in quality control for more than 20 years, have combined their own electronic pneumatic professional knowledge and years of technical training to launch various filling and sealing machines and filling capping machines, Plastic molding filling and sealing machine filling and sealing machine, fully meet the production requirements of customers and help customers create benefits; Time and again improve the service life of products and the simplicity of operation, so that the equipment I make is favored by enterprises, companies and factories at home and abroad.

I adhere to the enterprise oriented ideology and policy of "customer-oriented and product-based", so as to realize the integration of industrial chain, provide customers with multiple production engineering schemes, and provide packaging machinery and equipment with stable performance, excellent quality and reasonable price and immediate and thoughtful after-sales service, so as to solve actual production problems for customers with the most sincere attitude, Avoid unnecessary waste of expenses caused by enterprises. Strive to meet customers' purchase intention of value for money and value for money.

Tube Filling machine And Sealing machine is suitable for filling all kinds of paste and high viscosity fluids, suitable for filling large-diameter plastic pipes and composite pipes, and then the pipe is heated inside, and the batch number and date are printed on the seal. Used in pharmaceutical, food, cosmetics, adhesive, and other industries. Next, let me tell you about the related introduction and features of the Tube Filling machine And Sealing machine. Here are some answers.

Here is the content list:

l The related introduction of Tube Filling machine And Sealing machine.

l Design features of Tube Filling machine And Sealing machine.

l Features of Tube Filling machine And Sealing machine.

The related introduction of Tube Filling machine And Sealing machine.

Tube Filling machine And Sealing machine is a machine that fills the packaging into the container and seals it. After the product is put into the packaging container, to keep the product sealed, maintain product quality, and avoid product loss, the packaging container needs to be sealed. Tube Filling machine And Sealing machine is a machine with a compact design and automatic tube feeding. Tube Filling machine And Sealing machine's tube washing, feeding marking, filling, folding, sealing, coding, and finished product output are all performed by a fully automatic control system. The feeding of the washing pipe adopts a pneumatic method, which is accurate and reliable.

Design features of Tube Filling machine And Sealing machine.

First, the Tube Filling machine And Sealing machine is mechatronics, using multiple-introduction technology, controlled by PLC, and can automatically complete tube feeding, partial color labeling, filling, sealing, and tube outlet at the same time. The machine runs smoothly, is easy to control and size conversion, and is suitable for the production of pasty products. Second, the Tube Filling Machine And the Sealing machine has modern modeling, strong practicability, and high processing value. Third, the Tube Filling Machine And the Sealing machine have a stainless steel volumetric bulldozing syringe and a Teflon piston seal to achieve accurate dosage.

Features of Tube Filling machine And Sealing machine.

Tube Filling machine And Sealing machine is a piece of high-tech equipment successfully developed by introducing foreign advanced technology and combining GMP requirements. It has the characteristics of reasonable structure, complete functions, convenient operation, accurate filling, stable operation, and low noise. Tube Filling machine And Sealing machine adopts PLC controller, from liquid or high-speed material filling to batch number printing (including production date) automatic operation, is cosmetics, pharmaceuticals, food, adhesives and other ALU tubes, plastic tubes and multi-tube filling Ideal equipment for sealing, in line with GMP standards.

Wenzhou Zungwan Intelligent Machine Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream, ointment, fluid, and semi-fluid materials. If you are engaged in work related to Tube Filling machine And Sealing machine or want to know more about our company, you can communicate with us on the website. Our official website is https:// www.cnzpack.com/. Our company adheres to the service tenet of "customer first", and implements the service of honesty and customer first.

As people are enjoying life more and more now, most of the manual labor has been replaced. It is machine consumption. Mechanized operations not only restrict our hands, but more importantly, machine consumption is more efficient than our manual work. It is not only a little bit higher but also more hygiene, which has many benefits. Cartoning Machine is one such automated equipment. So, what are the feed inlets and characteristics of the Cartoning Machine? Let's go take a look next.

This is the content list:

l The feed inlet of the Cartoning Machine

l Features of Cartoning Machine

The feed inlet of the Cartoning Machine

Cartoning Machine feed is generally divided into three entrances: manual entrance, medicine bottle entrance, and machine package box entrance. The entire process of the Cartoning Machine from the machine package box feeding to the final packaging molding can be roughly divided into four stages: the carton is fixed by a guide rail and a push plate is used to open the carton. At the same time, there will be two cards that can move forward. The position is raised from below, jamming the sides of the carton from front to back, so that the box opens at a right angle and moves forward to the loading area.

After filling in the Cartoning Machine loading area, the mechanism of the machine folds the ears into the left and right guide rails and then performs the lid closing action. The front mechanism of the Cartoning Machine will first bend the tongue of the carton, and then a push plate pushes the lid to bend so that the tongue is inserted into the box and the lock is fastened. The closing action of the Cartoning Machine is critical, and the quality of the completion has a lot to do with the structure of the carton and the accuracy of the machine adjustment.

Features of the cartooning machine

1. Cartoning Machine has a low cost. Cartoning Machines can continue to work 24 hours a day. As long as the regular maintenance work is done, it can continue to produce as much as possible, and the production line only needs one or two people to take care of it, which effectively saves labor costs. Moreover, since the work of the Cartoning Machine is mass production, the products produced are more up to the standard with small differences. In addition to the high labor costs and individual differences in products, manual packaging is also affected by the emotions of workers.

2. Cartoning Machine has high production efficiency. The Cartoning Machine takes a fixed amount of time to complete a piece of cartooning work. In a fixed period, the total amount of products that can be completed is also fixed, and it will not be fluctuating. For enterprises, it is easier to calculate and control the cost. In addition, the Cartoning Machine has a fixed time to complete a piece of boxing work, and its efficiency is relatively improved. It can reduce the pressure on the staff in related positions, better manage, make the work orderly, and create more profits for the enterprise. many.

3. The Cartoning Machine has a high safety factor. Manual cartooning is unavoidable for negligence and fatigue, and accidents are prone to work accidents. The Cartoning Machine is used throughout the machine, with high accuracy of repeated operations, good stability, and strong safety. It can effectively prevent injuries to workers. Contribute to the safe and civilized production of enterprises.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It has a lot of experience in the production of cartooning machines. A large number of tests have been carried out before the Cartoning Machine leaves the factory to ensure the quality of the Cartoning Machine. If you are interested, you can contact us, our website is www.cnzpack.com.

Karmelle Liquid Filling

Automatic Rotary Small Plastic Tube Ice Ice Pop Fruit Juice Filling Sealing Machine …

Nasal Spray Filling Machine, Wholesale Various High Quality Nasal Spray Filling Machine Products from Global Nasal Spray Filling Machine Suppliers and Nasal Spray Contact Us Send …

Cartoning Process Cartoner equipment generally works according to the following 6 steps: Pick-up Carton Blank Erect Carton Transport Carton Fill Carton Seal Carton Output Packaged Carton As shown in the drawing below, which indicates the vertical cartoning process.

Cosmetic cream filling machine products My filters cosmetic cream Delete all …

Cartoning Machines CMH-I Intermittent Motion Horizontal Cartoning Machine Compact construction, Output range up to 75 folding boxes per minute Machine details CMH-C Continuous Motion Horizontal Cartoning Machine For bag-in-box applications, Output range up to 220 folding boxes per minute Machine details CMV Bag-in-Box The vertical Cartoning Machine

Tolyltriazole as Antitrust and Corrosion Inhibitor for Metals US

Vacuum Emulsifying Homogeneous Mixer,Detergent Homogeneous Mixer,Automatic Filling Production Line,Storage Tank,Automatic Tube Filling And Sealing Machine,Automatic Filling And Ca