The tube Filling machine And the Sealing machine are determined by multiple parameters. It is impossible to describe a Tube Filling machine And Sealing machine with any single parameter. Shaft power, blade displacement, pressure head, blade diameter, and filling speed are the five basic parameters that describe a Tube Filling Machine And Sealing machine. So, let's take a look at the principle of the Tube Filling machine And Sealing machine together. Here are some answers.
Here is the content list:
l Basic parameters.
l The shear rate of the fluid.
l Small slot and big slot.
The displacement of the blade is proportional to the flow rate of the blade itself, the first power of the blade speed, and the third power of the blade diameter. The shaft power consumed by the filling is proportional to the specific gravity of the fluid, the power standard of the blade itself, the third power of the speed, and the fifth power of the blade diameter. In the case of a certain power and blade form, the blade displacement and pressure head can be adjusted by changing the diameter of the blade and the matching of the speed. That is, the large diameter blade is equipped with a low-speed Tube Filling machine And a Sealing machine. High flow effect and low-pressure head, while the small diameter blade with high speed produces a higher pressure head and lower flow effect.
The shear rate of the fluid.
In the filling tank, the only way to make the micelles collide with each other is to provide a sufficient shear rate. According to the mechanism of the Tube Filling Machine And Sealing machine, it is because of the existence of fluid velocity difference that the fluid layers are mixed. Therefore, where the filling process always involves the fluid shear rate lhhaha620. Shear stress is a force that is the real cause of bubble dispersion and droplet breaking in filling applications. It must be pointed out that the shear rate at each point of the fluid in the entire stirred tank is not the same.
Small slot and big slot.
Experimental research shows that, as far as the blade area is concerned, no matter what type of blade, when the diameter of the blade is constant, the maximum shear rate and the average shear rate increase with the increase of the speed. However, when the rotation speed is constant, the relationship between the maximum shear rate and the average shear rate, and the diameter of the blade is related to the slurry type. When the rotation speed is constant, the maximum shear rate of the radial blade increases with the increase of the blade diameter, and the average shear rate has nothing to do with the diameter of the blade. These concepts about the shear rate of the blade area require special care in the design of the Tube Filling Machine And Sealing machine to reduce and enlarge. Because the small groove is compared with the large groove, the small groove Tube Filling Machine and Sealing machine often has the characteristics of high speed, small blade diameter, and low tip speed. The large groove Tube Filling Machine And Sealing machine often has the characteristics of low speed, large blade diameter, and high tip speed.
Our official website is https:// www.cnzpack.com/. If you are engaged in work related to the Tube Filling machine And Sealing machine, you can communicate with us on the website.
Korea East Asia Pharmaceutical Company, ordered a syrup filling line from our company, from bottle management - bottle washing - filling - corking - capping - labeling, the whole line in the Korean factory to complete the commissioning task, the whole line production design speed of 120 bottles per minute high-speed filling line.
In our production and life, the Liquid Filling Machine has a significant impact on many industries, so what is the method of using the Liquid Filling Machine? Let's go take a look next.
This is the content list:
l The ground wire must be well-grounded before the Liquid Filling Machine works
l Liquid Filling Machine liquid filling system assembly
The ground wire must be well-grounded before the Liquid Filling Machine works.
The ground wire must be well-grounded before the Liquid Filling Machine works, and then the appropriate standard syringe must be selected according to the different filling volumes. Generally, a 1ml syringe is used when the dispensing range is 0.2-1ml. Use a 5ml syringe for 1-5ml.use a 10ml syringe for 5-10ml. The 20ml model uses a 20ml glass infusion device. The 100ml model uses a 100ml glass infusion device, and the 500ml model uses the stainless steel filling system produced by our factory.
Liquid Filling Machine liquid filling system assembly
Pull out the inner core of the Liquid Filling Machine syringe, put the screw sleeve on the inner core of the syringe, and use the screw sleeve to properly fasten it to the lower base (cleanliness must be paid when disassembling the syringe). Place the upper clamp seat on the outlet end of the Liquid Filling Machine syringe jacket, and properly tighten the nuts on both sides to assemble the inner core and outer jacket of the installed Liquid Filling Machine syringe into one body. At this point, the Liquid Filling Machine injection system is assembled.
Place the Liquid Filling Machine valve with the arrow facing upwards and the arrow mark facing outwards and fix it on the fixing screw with a nut. Assemble the Liquid Filling Machine with a complete liquid filling system, align the upper and lower round holes of the liquid filling system components with the upper and lower fixing rods respectively, and put them on the bearing so that the outer end surface and the bearing surface are levels. When assembling the lower end, do not make the screw sleeve and the crank touch to prevent abnormal noise when the crank on the Liquid Filling Machine rotates (the screw sleeve and the crank are about 1mm apart when installed correctly). After the liquid filling system is installed correctly, tighten it. Tighten the screws up and down. Use a short hose to connect the Liquid Filling Machine syringe to the valve connection nozzle. The liquid inlet pipe is connected to the water inlet, and the liquid outlet pipe is connected to the water outlet. To prevent the liquid inlet and outlet pipes from being entangled, clip the liquid inlet and outlet pipes into the ear openings on the side of the casing.
Turn the crank of the Liquid Filling Machine by hand, it should be able to rotate freely, otherwise, the assembly is wrong, you should check whether the Liquid Filling Machine injection system is fastened to the rotating bearing.
Our company has obtained more than 20 invention patents and utility model patents. The main products are a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and online capping machine, capping machine and labeling machine, bottle unscrambler, tube filling and sealing machine, Cartoning machines, and other packaging equipment. If you are interested in Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.
In our production and life, the Cartoning Machine is of great significance to us, but sometimes, the Cartoning Machine will fail, so what is the reason for the failure of the Cartoning Machine? Next, let us analyze it together.
This is the content list:
Stop or stop between conveyor belts
The carton cannot be sucked down
The carton is not formed or ejected at the mouth of the box feeding template after being sucked
Can't suck the instructions
The paper rebounds during the suction process of the manual
The manual does not fold well
Uneven folding of the manual
There are curls and creases after the manual is folded
Manual stuck in the fence
1. Cartoning Machine shuts down at intervals to check if there is a shortage of materials and automatically starts up when supplemented.
2. Shut down the Cartoning Machine to check whether the power supply including the power supply part, the motor, or the governor is normal.
1. Whether the cartons of Cartons Machine are arranged neatly.
2. Whether the cartons of the Cartoning Machine are pasted together.
3. Whether the air pressure of the Cartoning Machine suction head is normal.
1. Check if the cartons of Cartons Machine are too hard.
2. Check whether the position of the guide rod of the cartons placed by the Cartoning Machine and the box delivery template are not correct.
3. Check whether the small hook spring at the rear of the Cartoning Machine delivery template is deformed.
4. Check if the height of the suction head of the Cartoning Machine and the box delivery track is correct.
1. Whether the Cartoning Machine manual is deformed, causing the suction head to fail to suck.
2. Whether the suction head gas of the Cartoning Machine is parallel to the manual.
3. Whether the paper width of the Cartoning Machine manual is different, the error must be within 1mm. The stacking position of the manual should be adjusted to a difference of 0.5mm from the inner edge when the suction head rises to the high position.
4. The small paper-separating hook above the suction head of the Cartoning Machine origami moves too early. Generally, the small hook should be inserted into the gap between the paper and the paper before the suction head is about to drop. The height of the small hook is adjusted to be 0.5mm away from the suction head when it is in the high position.
1. The foot-lifting action of the Cartoning Machine's manual was too early, and the manual was taken away by the foot support before being pulled down. The position of the feet of the Cartoning Machine is so that it does not touch the sucked manual when it is returned and it returns to the high position when the paper picking notch wheel has not pulled the paper.
2. Whether the matching speed of the Cartoning Machine suction head and paper picking wheel is the same. The suction head of the Cartoning Machine should be lowered first, and then the front part of the paper picking notch wheel should be pressed onto the paper.
1. Check if the Cartoning Machine paper is deformed and bent, and if there are burrs.
2. Is there any foreign matter in the fence of the Cartoning Machine blocking the paper?
3. The gap between the opening of the Cartoning Machine fence and the folding stick is too large, causing the paper to come out.
4. Is the gap between Cartons Machine's folding sticks too large to hold the paper? Adjust the adjusting screws at both ends of the folding stick to reduce the gap. If the Cartoning Machine folding stick has been used for too long and worn out, the folding stick must be replaced.
Check the Cartoning Machine to adjust the front and rear positions of the barriers in the fence to achieve the required folding size.
1. Is the gap between the Cartoning Machine baffle and the folding stick too large? Adjust the middle position of the baffle and folding stick.
2. If the middle position of the Cartoning Machine baffle and the folding stick has been adjusted, and there is still a large gap, remove the positioning pins on the Cartoning Machine baffle and re-adjust until the gap does not feed paper.
1. Whether the paper feeding gap of Cartoning Machine folding stick is too large and paper feeding is weak. The adjustment method is the same as above.
2. The installation position of the lower half of the Cartoning Machine fence is too long than the arc guide plate on it so that the paper cannot enter the folding stick below. Loosen all the fixing screws on the Cartoning Machine fence and adjust the board backward, but it should not be shorter than the upper guide plate and should be 1-3 mm longer than the guide plate. If it is shorter than the guide plate, the Cartoning Machine manual may go directly into the folding stick below without folding.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It will conduct a large number of tests before the Cartoning Machine leaves the factory to reduce the failure of the Cartoning Machine and provide warranty services. If you are interested in the Cartoning Machine, you can contact us Contact, our website is www.cnzpack.com.
Pharmaceutical Filler and Capper, whether semi-automatic or fully automatic, will encounter more or less in the process of using different places of failure, in the face of Pharmaceutical Filler and Capper's special parts of the failure, how do we find the problem as soon as possible and solve it? Let's take a look at it.
This is the content list:
l Pharmaceutical Filler and Capper's PLC failure
l Pharmaceutical Filler and Capper's Magnetic Switch Failure
l Pharmaceutical Filler and Capper solenoid valve failure
Pharmaceutical Filler and Capper PLC Failure
If the point controls Pharmaceutical Filler and Capper, the fault phenomenon is that the motor runs after the signal start Pharmaceutical Filler and Capper, but the motor does not stop running after the stop signal is issued. And Capper only stops running when the PLC is powered down. If the point controls the solenoid valve. The fault phenomenon is that the solenoid valve coil is not energized, and the cylinder is not reset. If the PLC of Pharmaceutical Filler and Capper is hit with external force to make the sticking point separate, it can assist to determine the fault of Pharmaceutical Filler and Capper.
Pharmaceutical Filler and Capper's magnetic switch failure
Pharmaceutical Filler and Capper's magnetic switch is used to detecting the position of the cylinder and control the cylinder travel. The four cylinders of laminating, pushing, pressing, and fusing knife are interrelated, and the magnetic switch is used to detect and control their positions. Pharmaceutical Filler and Capper failure is mainly manifested as the subsequent cylinders do not move, because the cylinder speed of Pharmaceutical Filler and Capper is faster, which causes the magnetic switch cannot detect the signal. Such as pushing the package cylinder speed is too fast, after pushing the package reset, the pressure package and fusion knife cylinder do not move.
Solenoid valve failure of Pharmaceutical Filler and Capper
Pharmaceutical Filler and Capper solenoid valve failure is mainly manifested as the cylinder does not move or does not reset, the reason is that Pharmaceutical Filler and Capper cylinder solenoid valve cannot change direction or tampering air. If the solenoid valve falters, the air pressure of Pharmaceutical Filler and Capper can't reach the working pressure because the inlet and outlet air paths are connected, and the knife beam doesn't rise to the place. the proximity switch of Pharmaceutical Filler and Capper knife beam protection doesn't work, and the precondition of full machine operation is not established. Pharmaceutical Filler and Capper does not operate, which is easily confused with an electrical fault. Solenoid valve air leakage sound, listen carefully to the source of sound and hand search for air leakage points, generally can easily identify the air leakage solenoid valve.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, with first-class product quality and efficient and fast after-sales service, forging the excellent products of "Central". Pharmaceutical Filler and Capper will undergo a lot of product testing before leaving the factory to reduce the probability of failure of Pharmaceutical Filler and Capper, and also provide customers with high-quality Pharmaceutical Filler and Capper warranty service. If you are interested in Pharmaceutical Filler and Capper, you can contact us, our website is www.cnzpack.com.
Bag Packing Machine consists of vacuum pump, motor, vacuum chamber, sealing strip, plexiglass plate cover, airbag, solenoid valve, etc. Bag Packing Machine is a general term for product production and outsourcing machines. It is mainly divided into two aspects, Bag Packing Machine assembly line production and packaging, used in the filling (filling), sealing machine, and coding of (bag, bottle) products in the food, medicine, chemical, and other industries. Bag Packing Machine product peripheral packaging equipment, used for spraying (printing) the production date, sealing, shrinking film, etc. after the product is produced. Then what is the principle and purpose of the Bag Packing Machine? Let's take a look together next.
This is the content list:
l Principle of Bag Packing Machine
l Bag Packing Machine is versatile
Principle of Bag Packing Machine
Bag packaging machine through the suction nozzle into the bag of the packaged goods, emptying air, from the suction nozzle discharge, and then complete sealing.
Bag Packing Machine is versatile
Bag Packing Machine is used in food, chemical, pharmaceutical and agricultural markets. Bag Packing Machine is easy to use and can complete multiple processes at once: bag pulling, bag making, filling, coding, counting, metering, sealing, product conveying, automatically, Bag Packing Machine is unmanned after setting. The Bag Packing Machine is highly efficient. In the Chinese market, the output of fully automatic packaging machines can approach 120-240 bags per minute to replace the old-time manual products, whose output is far more than several times the time. Bag Packing Machine clean, hygienic, and energy-efficient. Bag Packing Machine has the function of clean, hygienic, material saving, bag saving, money saving, and environmental protection.
Since the 1950s, my country's plastic machinery manufacturing industry has undergone rapid development for nearly half a century, especially since the reform and opening up. The Bag Packing Machine has now been built with a complete range of products, the main technical and economic indicators are close to or have reached the advanced level, and the supporting facilities are becoming more and more advanced. Production is gradually specialized, Bag Packing Machine has a large-scale and complete industrial system, and Bag Packing Machine products meet the needs of the domestic market.
We have obtained ISO9001 quality management system certification, and some products have passed CE certification. The main products are a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and online capping machine and labeling machine, bottle unscrambler, tube filling and sealing machine, cartooning machine, and other packaging equipment. The quality of our Bag Packing Machine and service as well as our integrity are widely praised at home and abroad. We will carry forward the spirit of "comprehensive innovation and perseverance", self-discipline and strive for the first place, and provide new and old customers with better and more complete services with enthusiasm and a new attitude. If you are interested in Bag Packing Machine, you can contact us, our website is www.cnzpack.com.
The Cosmetic Filling machine And Capping machine integrates the functions of air purification, filling, inserting, capping, and venting. It is suitable for filling water injection, lotion, and cream products. The Cosmetic Filling machine And Capping machine has the advantages of reasonable design, stable performance, accurate quantity, glass tabletop, automatic bottle feeding, smooth operation and no noise, electric speed regulation of filling speed and filling volume, and convenient maintenance and cleaning. Next, let's take a look at the description and structural characteristics of the Cosmetic Filling machine And capping Machine. Here are some answers.
Here is the content list:
Description of Cosmetic Filling machine And Capping machine.
Structural characteristics of Cosmetic Filling machine And Capping machine.
The Cosmetic Filling machine And Capping machine adopts automatic low-vacuum filling, automatic bottle detection (no bottle no filling), three fillings, automatic lowering of the nozzle cap, circulation of the perfume bottle die, and wide adaptability. It can meet the volume of containers of different sizes and filling requirements. Cosmetic Filling Machine And Capping machine is equipped with air bottle cleaning, quantitative filling, negative pressure filling, pumping, roll cap, jacket, screw cap, rejection, labeling, and finished product collection. The mold moves in a circular motion, which makes it easy to change the bottle. The stepper motor is used for quantitative filling, and the filling volume can be adjusted quickly. The negative pressure device is used to fill the same liquid level and the manipulator releases the pump to increase the pump roll rate; the elastic rolling head is to avoid damage to the bottle body.
The design of the Cosmetic Filling machine And Capping machine is very reasonable. The Cosmetic Filling machine And Capping machine has a reasonable and compact structure, stable operation, flexible operation, and convenient specification conversion and adjustment. The speed of the aluminum cover is adjustable. Using the principle of seven-station three-knife cap rolling, the aluminum cap is rolled without damage, and the rolling mouth is firm, smooth and flat. The operation of the machine is very simple. The internal pneumatic part adopts new pneumatic components. The piston and cylinder of cylinder are made of PTFE and stainless steel, which meets the requirements of GMP testing. The filling speed can be adjusted at will with high precision. The Cosmetic Filling machine And Capping machine can be modified according to actual production needs and can be transformed into a multi-head type, explosion-proof type, and overflow type system.
Wenzhou Zungwan Intelligent Machine Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream, ointment, fluid, and semi-fluid materials. Our official website is https:// www. cnzpack.com/. If you are engaged in work related to Cosmetic Filling machines And Capping machines or want to learn more about our company, you can communicate with us on the website. Our company adheres to the service tenet of "customer first", and implements the service of honesty and customer first.
Tube Filling machine And Sealing machine adopt the latest module circuit, stable working performance, high efficiency, and all components adopt famous brand products. Under the careful design of our company, various advanced Tube Filling Machine And Sealing machines have been produced. Mainly used for sealing toothpaste, cosmetics, medicine, food, industrial products, and various hoses. Next, let's take a look at the cleaning and maintenance of the Tube Filling machine And Sealing machine. Here are some answers.
Here is the content list:
Tube Filling machine And Sealing machine cleaning.
Daily maintenance of Tube Filling machine And Sealing machine.
First, regularly clean the surface of the Tube Filling machine And Sealing machine, the bottom plate and the lower mold slide plate, grooves, the upper mold inner pressure plate, and the positioning rod. Second, grease should be added to the transmission parts of the lower mold slide plate, pressing rod bearing, eccentric wheel and guidepost, guide rail, and so on regularly to ensure the performance of the Tube Filling Machine And Sealing machine. Third, the method of cleaning the toothed knife: first plug the two drain holes of the lower mold with a cotton ball, pour boiling water into the groove of the lower mold, until it is full, then push the slide of the lower mold into place, and lower the upper mold. Press to the lowest point, let the toothed knife soak for a few minutes until it is clean, repeat several times.
First, check the equipment ground wire frequently to ensure reliable contact; clean the weighing platform frequently; check whether the pneumatic pipeline is leaking and whether the air pipe is broken. Second, change the lubricating oil of the reducer motor every year, check the tightness of the chain, and adjust the tension in time. Third, the sensor of the Tube Filling Machine And Sealing machine is a high-precision, high-sealing, and high-sensitivity device. Impact and overload are strictly prohibited, and no contact is allowed during the working process, and it is not allowed to be disassembled if it is not required for maintenance. Fourth, if it is not used for a long time, empty the material in the pipeline. Fifth, observe the moisture filter and oil mist device of the pneumatic combination two-piece before going to work every day. Sixth, during the production, we should always patrol and observe the mechanical parts to see if the rotation and lifting are normal if there is any abnormality, and if the screws are loose. Seventh, do a good job of cleaning and sanitation, keep the surface of the Tube Filling machine And Sealing machine clean, often remove the accumulation on the scale body, and pay attention to keeping the electric control cabinet clean.
Wenzhou Zungwan Intelligent Machine Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream, ointment, fluid, and semi-fluid materials. If you are engaged in work related to Tube Filling machine And Sealing machine or want to know more about our company, you can contact us. Our official website is https:// www.cnzpack.com/.