











In our production and life, the Liquid Filling Machine has a significant impact on many industries, so what is the method of using the Liquid Filling Machine? Let's go take a look next.
This is the content list:
l The ground wire must be well-grounded before the Liquid Filling Machine works
l Liquid Filling Machine liquid filling system assembly
The ground wire must be well-grounded before the Liquid Filling Machine works.
The ground wire must be well-grounded before the Liquid Filling Machine works, and then the appropriate standard syringe must be selected according to the different filling volumes. Generally, a 1ml syringe is used when the dispensing range is 0.2-1ml. Use a 5ml syringe for 1-5ml.use a 10ml syringe for 5-10ml. The 20ml model uses a 20ml glass infusion device. The 100ml model uses a 100ml glass infusion device, and the 500ml model uses the stainless steel filling system produced by our factory.
Liquid Filling Machine liquid filling system assembly
Pull out the inner core of the Liquid Filling Machine syringe, put the screw sleeve on the inner core of the syringe, and use the screw sleeve to properly fasten it to the lower base (cleanliness must be paid when disassembling the syringe). Place the upper clamp seat on the outlet end of the Liquid Filling Machine syringe jacket, and properly tighten the nuts on both sides to assemble the inner core and outer jacket of the installed Liquid Filling Machine syringe into one body. At this point, the Liquid Filling Machine injection system is assembled.
Place the Liquid Filling Machine valve with the arrow facing upwards and the arrow mark facing outwards and fix it on the fixing screw with a nut. Assemble the Liquid Filling Machine with a complete liquid filling system, align the upper and lower round holes of the liquid filling system components with the upper and lower fixing rods respectively, and put them on the bearing so that the outer end surface and the bearing surface are levels. When assembling the lower end, do not make the screw sleeve and the crank touch to prevent abnormal noise when the crank on the Liquid Filling Machine rotates (the screw sleeve and the crank are about 1mm apart when installed correctly). After the liquid filling system is installed correctly, tighten it. Tighten the screws up and down. Use a short hose to connect the Liquid Filling Machine syringe to the valve connection nozzle. The liquid inlet pipe is connected to the water inlet, and the liquid outlet pipe is connected to the water outlet. To prevent the liquid inlet and outlet pipes from being entangled, clip the liquid inlet and outlet pipes into the ear openings on the side of the casing.
Turn the crank of the Liquid Filling Machine by hand, it should be able to rotate freely, otherwise, the assembly is wrong, you should check whether the Liquid Filling Machine injection system is fastened to the rotating bearing.
Our company has obtained more than 20 invention patents and utility model patents. The main products are a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and online capping machine, capping machine and labeling machine, bottle unscrambler, tube filling and sealing machine, Cartoning machines, and other packaging equipment. If you are interested in Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.
Pharmaceutical Filler and Capper have been used by more and more companies in the industry, and many operators have learned how to use Pharmaceutical Filler and Capper, but they do not know much about its properties and working principle, so when Pharmaceutical Filler and Capper malfunctions, there is no way to start. So what is the working principle of Pharmaceutical Filler and Capper? Let's take a look at it.
This is the content list:
l Introduction of Pharmaceutical Filler and Capper
l Pharmaceutical Filler and Capper working principle
Introduction of Pharmaceutical Filler and Capper
Pharmaceutical Filler and Capper is a machine for filling and sealing objects, which is a small product in the packaging machine and is divided into the semi-automatic filling machine and fully automatic filling line in terms of the degree of automation of Pharmaceutical Filler and Capper production. From the point of view of packaging materials can be divided into liquid filling machinery, paste filling machine, powder filling machine, granule filling machine. Recently, with the QS certification of food, many manufacturers have started to focus on the quality and packaging of Pharmaceutical Filler and Capper.
Pharmaceutical Filler and Capper working principle
For Pharmaceutical Filler and Capper to achieve the linkage effect, it is driven by transmission machinery, so that all parts can work in coordination. When Pharmaceutical Filler and Capper reaches a certain number of bottles, there is a special infrared sensor on the inlet track to receive the induction, which automatically catches the bottles behind and allows the bottles in front to be filled. After the bottles are filled, then let the bottles behind enter to fill the space, to realize no bottle without filling. When the bottles enter the position under the filling head, the other working sections stop and only the filling headworks, when the bottles leave, the Pharmaceutical Filler and Capper's head stops working, the track section works and the bottle stopper is released. The clean bottles coming out of the bottle washer are fed into the inlet spiral of Pharmaceutical Filler and Capper by the bottle feeding belt and sent to the bottle-holding cylinder on the rotary table through the bottle feeding star wheel and raised, the bottle mouth is guided by the centering device and pressed against the lower part of the filling valve to form a seal. After being evacuated, the backpressure gas (CO,) in the storage cylinder is rushed into the bottle, when the gas pressure in the bottle is equal to the gas pressure in the storage cylinder, the liquid valve opens under the action of the liquid valve spring, at this time, the object is automatically filled into the glass bottle along the bottle wall through the guidance of the umbrella type reflective ring on the return tube and is replaced into the storage cylinder through the return tube, when the object rises to a certain height and closes the return tube mouth. Automatically stop down the object. Then the liquid valve and gas valve are closed to drain the pressure gas in the neck part of the bottle to prevent the gushing of the object with gas when the glass bottle is descending so that the whole filling process is completed This is the main working principle of Pharmaceutical Filler and Capper, and the users can use it according to these Users can know clearly which part of the machine has problems and repair them according to these features of Pharmaceutical Filler and Capper.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, constantly researching and developing packaging machinery for various materials such as liquid, powder, cream/oil, fluid, and semi-fluid. Extensive tests are conducted before the Pharmaceutical Filler and Capper leave the factory to ensure the quality of products and maintain the healthy development of the Pharmaceutical Filler and Capper market. If you are interested in Pharmaceutical Filler and Capper, you can contact us at www.cnzpack.com. You are very welcome and we look forward to working with you.
With the increasingly fierce competition in the manufacturing and production of plastic bottles in the food and pharmaceutical industries, Bottle Unscrambler has become more and more solid backing for the food and pharmaceutical plastic bottle markets. So how does it play a role? We will introduce the work process and personnel operation specifications of Bottle Unscrambler. Let's take a look together next.
This is the content list:
The workflow of Bottle Unscrambler
Personnel operation specification of Bottle Unscrambler
The workflow of Bottle Unscrambler is generally as follows: manually put materials into the storage bottle library, the materials in the storage bottle library will be automatically quantified and fed to the turntable at the set speed. The turntable rotates at a high speed to supply the bottles as required, the web wheel The irregular bottles are removed, and the bottle dividing part sends the bottles from the turntable to the bottle unscramble part at a certain speed. The Bottle Unscrambler part of the Bottle Unscrambler clamps the bottles to the working surface of the conveyor through the conveyor belts on both sides, and at the same time sorts the bottles through the bottle turner. The Bottle Unscrambler electronic control system performs real-time monitoring and feedback through the sensors of each part to achieve fully automated operation requirements, and save a lot of labor costs and avoid losses caused by human error factors.
To ensure the normal and safe operation of Bottle Unscrambler, there are special operating procedures established for it. Operators and equipment management personnel shall perform standardized operations of Bottle Unscrambler under these procedures. This safe operation specification is commonly used in Bottle Unscramblers, mixers, high-speed automatic Bottle Unscramblers, etc.
1. First check the Bottle Unscrambler's intact, clean, and expiration status identification and the equipment operation record of the shift. If the inspection finds that the Bottle Unscrambler has exceeded the cleaning validity period, it is necessary to further clean the equipment according to the equipment cleaning operation rules and fill in the equipment status identification.
2. Check the Bottle Unscrambler and the Bottle Unscrambler to confirm that there is no foreign matter, and turn the bottle plate and unscrambler to confirm that it can work normally.
3. Turn on the Bottle Unscrambler power switch, check the touch screen and three photoelectric switches. If both are energized, the lack of a bottle alarm will be displayed on the touch screen. When the electric eye is blocked by hand, the screen displays the blocking alarm, and the two photoelectric switches are in a normal state.
4. Turn on the Bottle Unscrambler compressed air, use the bottom of the bottle to shake under the electric eye of the bottle puller, compressed air will be sprayed out, and the equipment can be turned on normally.
To ensure that the various parts of the Bottle Unscrambler can work normally, the formal operation can be divided into five steps: click the host start and lift start on the touch screen respectively, and observe whether the Bottle Unscrambler has abnormal noise when it is running. After powering on the Bottle Unscrambler and confirming that there is no abnormal condition, stop the device, but the qualified infusion bottle upright in the bottle feeding bracket, and start the device again. The bottle will pass through the rotating carousel of the device and enter the conveyor belt to start the bottle unscramble operation. Run at low speed when starting up, and then adjust the lifting speed and unscramble speed according to the actual production, so that the speed of the Bottle Unscrambler equipment can match the actual production speed. To prevent such phenomena from happening. If such a phenomenon occurs, stop the machine immediately to eliminate the fault before it can continue to run. During the operation of the equipment, the bottles should be put in continuously, and observe whether there are phenomena such as pouring, jamming, broken bottles, etc. If any, stop the machine immediately and start the production after troubleshooting. After the production is over, stop the equipment, turn off the power of the Bottle Unscrambler, and clear the remaining materials out of the equipment.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. When the Liquid Filling Machine leaves the factory, it will provide customers with detailed Liquid Filling Machine operation procedures and operating specifications. If you are interested in Liquid Filling Machine, you can contact us, our website is www.cnzpack.com.
Wenzhou Zungwan Intelligent Machine Co.,Ltd. is the professional equipment manufacturer to keep researching and developing the packing machinery for every type of liquid, powder, cream/ointment, fluid and half-fluid etc. materials. We have Obtained ISO9001 quality management system authentication and parts of our products have passed CE authentication. Our company has obtained more than 20 invention patents and utility model patents. The main products range from nail polish filling machine, perfume machine,perfume filling machine, powder serial automatically volume-measuring packing machine and inline capping machine, rotary capping machine and labeling machine, bottle unscrambler , screw capping machine ,tube filling and sealing machine, cartoning machine and other Packaging equipments.
So far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and our service as well as our integrity is acclaimed both in China and abroad. we will carry forward the spirit of "integrated innovation, and perseverance," discipline ourselves to be the first, and provide better and more perfect service for our new and old customers with enthusiasm and a new attitude.
Capping Machine operation, accuracy error, installation adjustment, equipment cleaning, maintenance, and other aspects are very simple and convenient. Capping Machine has been widely used in various industries such as daily chemical and grease, and can fill different high-viscosity fluids. So what are the working principles and structural characteristics of the Capping Machine? Let's take a look together next.
This is the content list:
l How Capping Machine works
l Structural characteristics of Capping Machine
How Capping Machine works
The Capping Machine adopts a new horizontal design, which is light and convenient and can automatically pump the material. For thicker slurry, a hopper can be added. When the Capping Machine is in the "auto" state, the Capping Machine will automatically perform continuous filling at a set speed. Capping Machines can be divided into three types: atmospheric filling machine, vacuum filling machine, and pressure filling machine.
Under normal pressure, Capping Machine can fill the liquid in a self-flowing manner according to the weight of the liquid itself. The filling method is to fill at a pressure greater than atmospheric pressure. The pressure in the liquid storage tank is greater than the pressure in the bottle, and the liquid that needs to be filled will enter the bottle depending on the pressure difference. The key component of the Capping Machine is the PLC operation control system. Under normal pressure, Capping Machine can fill the liquid in a self-flowing manner according to the weight of the liquid itself. The filling method is to fill at a pressure greater than atmospheric pressure. The pressure in the liquid storage tank is greater than the pressure in the bottle, and the liquid that needs to be filled will enter the bottle depending on the pressure difference. The key component of the Capping Machine is the PLC operation control system.
The principle of the Capping Machine is relatively easy to understand. The improved control system simplifies the structure of the machine. It can be seen from the operating conditions and control efficacy tests of the actual application that the automation level of the system has reached the design requirements. This reduces the labor intensity of the operator and makes the production line that needs filling production about 30% higher than before, so the probability of failure of the Capping Machine is significantly reduced.
Structural characteristics of Capping Machine
The design of the Capping Machine is very reasonable and appropriate, the remainder of the machine is very small, and the operation and use are very simple. The pneumatic parts inside the Capping Machine all use new pneumatic components. The piston and cylinder of the Capping Machine cylinder are made of polytetrafluoroethylene and stainless steel to meet the requirements of GMP testing. The filling quantity and filling speed of the Capping Machine can be adjusted at will, and the degree is relatively high.
The Capping Machine can be modified according to actual production needs. It can be transformed into a multi-head system, explosion-proof system, and overflow system. The Capping Machine is suitable for use in food, daily necessities, pesticides, and other industries, and has a broad application prospect.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. The company strictly controls the quality of the Capping Machine. If you are interested in Capping Machine, you can contact us, our website is www.cnzpack.com. I look forward to your coming and hope to cooperate with you.
Speaking of Bag packaging machines for large machinery, it is necessary to briefly talk about the knowledge of stand-up pouches. Bag packaging machines in the application, development, and growth of stand-up pouches played a role in what? Let's look at it together next.
This is the list of contents:
Stand-up pouches in brief
The basic classification of stand-up pouches
Stand-up pouches produced by Bag packaging machines are flexible packaging bags with a horizontal support structure at the bottom. It does not rely on any support, whether the bag is opened or not, it can stand on its own. Since its appearance and promotion, stand-up pouches have been very popular. With their good design and function, they have been widely used in food, daily necessities, pharmaceuticals, and other fields. Stand-up pouches produced by Bag packaging machines are mainly used for juice drinks, sports drinks, spices, and other products. In addition to the food industry, the application of some Bag packaging machine products such as detergents, daily cosmetics, pharmaceuticals, etc. is gradually increasing.
The basic classification of stand-up pouches
1. Ordinary stand-up pouches
That is, the general form of the Bag packaging machine produced by the stand-up pouches in the form of four seals, cannot be resealed and reopened. This stand-up pouch packaging machine to produce stand-up pouches is generally used in the industrial supplies industry.
2. Stand-up pouches with suction nozzles
Stand-up pouches with suction nozzles produced by the Bag packaging machine are more convenient to pour or suck out the contents and can be re-closed and re-opened at the same time. It can be thought of as a combination of stand-up pouches and ordinary bottle spout.
3. Stand-up pouches with zipper
Stand-up pouches with zippers produced by the Bag packaging machine can also be re-closed and re-opened. As the zipper produced by the Bag packaging machine is not closed, the seal strength is limited, so this form is not suitable for packaging liquids and volatile substances.
4. Special-shaped stand-up pouches
That is, according to the packaging needs, based on the traditional packaging bags, change the Bag packaging machine production of a variety of new shapes of stand-up pouches, such as waist design, bottom deformation design, handle design, etc.
Bag packaging machine production of stand-up pouches not only improves the product grade, but also strengthens the visual effect of the shelf, and is easy to carry, easy to use, with good preservation and sealing performance. The development of stand-up pouches produced by the Bag packaging machine, but also the packaging machinery industry to follow the trend, the development of adaptable Bag packaging machine.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops a wide range of packaging machinery for liquid, powder, cream/paste, fluid, and semi-fluid materials. We have obtained ISO9001 quality management system certification and some of our products have passed CE certification. Our company has obtained more than 20 invention patents and utility model patents. Our main products include a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and in-line capping machine, capping machine and labeling machine, bottle management machine, tube filling and sealing machine, cartooning machine, and other packaging equipment. If you are interested in a Bag packaging machine, you can contact us, our website is www.cnzpack.com.
After we purchase Pharmaceutical Filler and Capper, we need to install and debug Pharmaceutical Filler and Capper. Let's take a look at it together next.
This is the content list:
l Installation of Pharmaceutical Filler and Capper
l Commissioning of Pharmaceutical Filler and Capper
l Maintenance of Pharmaceutical Filler and Capper
Installation of Pharmaceutical Filler and Capper
According to different models and specifications of Pharmaceutical Filler and Capper, refer to the random manual for installation.
For small-sized Pharmaceutical Filler and Capper, it is not required to build the foundation, just install it on the flat workshop floor, make a good horizontal reference, adjust the elevation of incoming and outgoing chain belt according to the layout diagram, and adjust the legs to make the load of the whole machine evenly distributed.
For large-sized Pharmaceutical Filler and Capper, it is necessary to build a solid installation foundation as required. When installing, the horizontal benchmark should be played, especially when it is connected with the capping machine, the two parts of the incoming and outgoing bottle belts must be at the same horizontal benchmark.
To ensure the smooth bottle delivery of Pharmaceutical Filler and Capper, the inlet pallet under the inlet star wheel should be 0.5mm higher than the surface of the bottle tray, and the outlet pallet under the middle star wheel should be 0.5mm lower than the surface of the bottle tray. The running is free and there should be no jamming interference. The horizontal part of the liquid inlet pipe should have a certain slope to facilitate emptying and air discharge. Make sure the bearing load of Pharmaceutical Filler and Capper's legs is even. Matching equipment with the host, such as gas-liquid control box, vacuum pump system and electric control box, etc. are generally installed separately.
Commissioning of Pharmaceutical Filler and Capper
After confirming the installation of Pharmaceutical Filler and Capper is completed, the commissioning of Pharmaceutical Filler and Capper can be carried out step by step as follows. Replace suitable accessories according to the bottle type filled by Pharmaceutical Filler and Capper, and adjust the parts, including the inlet screw, guide bar spacing, side guard safety switch, star-shaped paddle wheel, reservoir, and capping head height adjustment, etc. Thoroughly clean the Pharmaceutical Filler and Capper reservoir, liquid piping, and gas piping to ensure that there is no foreign material. Make a hydraulic test on the storage tank and pipeline at the same time. Check carefully whether the wiring of the Pharmaceutical Filler and Capper control box is correct, and turn on the main switch only after the equipment is turned manually without jamming. Start the equipment in a pointing way to check if there is any abnormality. Start the Pharmaceutical Filler and Capper at low speed and check the starting, braking, emergency stop, and speed regulation performance. Then infuse an empty bottle at low speed, check whether it can pass through the bottle feed screw, guide bar, and star wheel smoothly and whether each control touch block can respond sensitively. Check whether the Pharmaceutical Filler and Capper can drop the cap smoothly and seal the cap tightly. After that, adjust the value of each instrument on the liquid and gas control cabinet according to the filing requirements of Pharmaceutical Filler and Capper. Check the liquid level and pressure of Pharmaceutical Filler and Capper reservoir, make filling test, adjust the filling head and control the bottling level.
Maintenance of Pharmaceutical Filler and Capper
Pharmaceutical Filler and Capper in the process of use, must be required to carry out regular maintenance. First of all, we must ensure that the lubrication status of the Pharmaceutical Filler and Capper must be good, and the lubrication points must be well-lubricated in time to maintain the oil level of each tank and the intact spray lubrication function. Timely replacement of a variety of damaged parts, such as seals, bottle transport parts, and transmission parts in the wearing parts. The movable parts that are not adjusted for a long time, such as the reservoir of Pharmaceutical Filler and Capper and the height adjustment device of the capping machine, should be run regularly to avoid rust and corrosion. Regularly and regularly clean the liquid tank of Pharmaceutical Filler and Capper, liquid delivery tube, filling valve, and parts that may contact with liquid as required. Liquid residue, oil, water, and glass fragments should be removed to keep the equipment neat and hygienic. Since there are many models and specifications of Pharmaceutical Filler and Capper, and the performance, structure, and working principle vary greatly, operators and maintenance personnel should use and maintain them according to the operation manuals accompanying each machine.
Our products are in great demand in both domestic and international markets, and we are committed to improving and developing to meet our customers and the market demand is our eternal theme and sincere commitment to our customers. If you are interested in Pharmaceutical Filler and Capper, you can contact us, our website is www.cnzpack.com.
Liquid Filling Machine is specially designed for filling easy-to-open bottles. It has a reasonable design, simple structure, easy operation, and a mechanical bottle stop filling device. So what is the working principle of a Liquid Filling Machine? Let's take a look together next.
This is the content list:
l Transmission principle of Liquid Filling Machine
l The principle of the filling part of the Liquid Filling Machine
l Liquid Filling Machine's capping system
l The capping head of the Liquid Filling Machine
l The Liquid Filling Machine's tracking and filling mechanism
The Liquid Filling Machine transmits the power to the worm gear shaft of the reducer through the belt pulley, and then the worm gear shaft transmits the power to the paddlewheel shaft, the filling part, and the capping head through each gear. the filling part, the capping head, and each paddle wheel of the Liquid Filling Machine move synchronously, and the power is transmitted to the bottle feeding paddle wheel device through the bevel gear.
The liquid bottle of the Liquid Filling Machine is sent to the transition pulley by the large bottle inlet paddlewheel and then sent to the synchronous belt by the transition pulley. The bottle is dragged forward at a uniform speed by the inserts on the synchronous belt, and the filling needle of the Liquid Filling Machine is inserted into the bottle mouth under the control of the tracking mechanism and runs forward synchronously with the bottle to achieve tracking and filling. The diving needle rises with the liquid level to play the role of defoaming.
The cap supply system of the Liquid Filling Machine is composed of a cap delivery track, cap handling head, and cap-wearing mechanism. The lid management head adopts the principle of electromagnetic spiral oscillation to line up the messy lids and enter the lid delivery track through the reversing twist channel. When the Liquid Filling Machine passes through the lid-wearing mechanism, the bottle hangs on to the lid and passes through the pressure plate to make the lid wear correctly.
After the liquid bottle of Liquid Filling Machine enters the cap rolling head turntable with the cap on, the three rolling knives which have been opened will turn forward with the Liquid Filling Machine turntable with the bottle as the center and press the cap under the control of the cam, then the three rolling knives will roll towards the cap at the same time under the action of the cone sleeve, and after rolling, they will leave the cap at the same time and return to the original position.
The Liquid Filling Machine drives the gear and rack to move, thus driving the filling needle to do the reciprocating movement. By adjusting the relative position of the Liquid Filling Machine's syringe holder and mounting frame, the filling needle can be accurately inserted into the middle of the bottle opening.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, and so far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and services as well as our integrity are widely praised at home and abroad. We will carry forward the spirit of "comprehensive innovation, perseverance", self-discipline and strive for the first, with enthusiasm and a new attitude to provide more perfect service for new and old customers. If you are interested in Liquid Filling Machine, please contact us, our website is www.cnzpack.com