Installation and debugging of Pharmaceutical Filler and Capper

After we purchase Pharmaceutical Filler and Capper, we need to install and debug Pharmaceutical Filler and Capper. Let's take a look at it together next.

This is the content list:

l Installation of Pharmaceutical Filler and Capper

l Commissioning of Pharmaceutical Filler and Capper

l Maintenance of Pharmaceutical Filler and Capper

Installation of Pharmaceutical Filler and Capper

According to different models and specifications of Pharmaceutical Filler and Capper, refer to the random manual for installation.

For small-sized Pharmaceutical Filler and Capper, it is not required to build the foundation, just install it on the flat workshop floor, make a good horizontal reference, adjust the elevation of incoming and outgoing chain belt according to the layout diagram, and adjust the legs to make the load of the whole machine evenly distributed.

For large-sized Pharmaceutical Filler and Capper, it is necessary to build a solid installation foundation as required. When installing, the horizontal benchmark should be played, especially when it is connected with the capping machine, the two parts of the incoming and outgoing bottle belts must be at the same horizontal benchmark.

To ensure the smooth bottle delivery of Pharmaceutical Filler and Capper, the inlet pallet under the inlet star wheel should be 0.5mm higher than the surface of the bottle tray, and the outlet pallet under the middle star wheel should be 0.5mm lower than the surface of the bottle tray. The running is free and there should be no jamming interference. The horizontal part of the liquid inlet pipe should have a certain slope to facilitate emptying and air discharge. Make sure the bearing load of Pharmaceutical Filler and Capper's legs is even. Matching equipment with the host, such as gas-liquid control box, vacuum pump system and electric control box, etc. are generally installed separately.

Commissioning of Pharmaceutical Filler and Capper

After confirming the installation of Pharmaceutical Filler and Capper is completed, the commissioning of Pharmaceutical Filler and Capper can be carried out step by step as follows. Replace suitable accessories according to the bottle type filled by Pharmaceutical Filler and Capper, and adjust the parts, including the inlet screw, guide bar spacing, side guard safety switch, star-shaped paddle wheel, reservoir, and capping head height adjustment, etc. Thoroughly clean the Pharmaceutical Filler and Capper reservoir, liquid piping, and gas piping to ensure that there is no foreign material. Make a hydraulic test on the storage tank and pipeline at the same time. Check carefully whether the wiring of the Pharmaceutical Filler and Capper control box is correct, and turn on the main switch only after the equipment is turned manually without jamming. Start the equipment in a pointing way to check if there is any abnormality. Start the Pharmaceutical Filler and Capper at low speed and check the starting, braking, emergency stop, and speed regulation performance. Then infuse an empty bottle at low speed, check whether it can pass through the bottle feed screw, guide bar, and star wheel smoothly and whether each control touch block can respond sensitively. Check whether the Pharmaceutical Filler and Capper can drop the cap smoothly and seal the cap tightly. After that, adjust the value of each instrument on the liquid and gas control cabinet according to the filing requirements of Pharmaceutical Filler and Capper. Check the liquid level and pressure of Pharmaceutical Filler and Capper reservoir, make filling test, adjust the filling head and control the bottling level.

Maintenance of Pharmaceutical Filler and Capper

Pharmaceutical Filler and Capper in the process of use, must be required to carry out regular maintenance. First of all, we must ensure that the lubrication status of the Pharmaceutical Filler and Capper must be good, and the lubrication points must be well-lubricated in time to maintain the oil level of each tank and the intact spray lubrication function. Timely replacement of a variety of damaged parts, such as seals, bottle transport parts, and transmission parts in the wearing parts. The movable parts that are not adjusted for a long time, such as the reservoir of Pharmaceutical Filler and Capper and the height adjustment device of the capping machine, should be run regularly to avoid rust and corrosion. Regularly and regularly clean the liquid tank of Pharmaceutical Filler and Capper, liquid delivery tube, filling valve, and parts that may contact with liquid as required. Liquid residue, oil, water, and glass fragments should be removed to keep the equipment neat and hygienic. Since there are many models and specifications of Pharmaceutical Filler and Capper, and the performance, structure, and working principle vary greatly, operators and maintenance personnel should use and maintain them according to the operation manuals accompanying each machine.

Our products are in great demand in both domestic and international markets, and we are committed to improving and developing to meet our customers and the market demand is our eternal theme and sincere commitment to our customers. If you are interested in Pharmaceutical Filler and Capper, you can contact us, our website is www.cnzpack.com.