











Tube Filling machine And Sealing machine adopt the latest module circuit, stable working performance, high efficiency, and all components adopt famous brand products. Under the careful design of our company, various advanced Tube Filling Machine And Sealing machines have been produced. Mainly used for sealing toothpaste, cosmetics, medicine, food, industrial products, and various hoses. Next, let's take a look at the cleaning and maintenance of the Tube Filling machine And Sealing machine. Here are some answers.
Here is the content list:
Tube Filling machine And Sealing machine cleaning.
Daily maintenance of Tube Filling machine And Sealing machine.
First, regularly clean the surface of the Tube Filling machine And Sealing machine, the bottom plate and the lower mold slide plate, grooves, the upper mold inner pressure plate, and the positioning rod. Second, grease should be added to the transmission parts of the lower mold slide plate, pressing rod bearing, eccentric wheel and guidepost, guide rail, and so on regularly to ensure the performance of the Tube Filling Machine And Sealing machine. Third, the method of cleaning the toothed knife: first plug the two drain holes of the lower mold with a cotton ball, pour boiling water into the groove of the lower mold, until it is full, then push the slide of the lower mold into place, and lower the upper mold. Press to the lowest point, let the toothed knife soak for a few minutes until it is clean, repeat several times.
First, check the equipment ground wire frequently to ensure reliable contact; clean the weighing platform frequently; check whether the pneumatic pipeline is leaking and whether the air pipe is broken. Second, change the lubricating oil of the reducer motor every year, check the tightness of the chain, and adjust the tension in time. Third, the sensor of the Tube Filling Machine And Sealing machine is a high-precision, high-sealing, and high-sensitivity device. Impact and overload are strictly prohibited, and no contact is allowed during the working process, and it is not allowed to be disassembled if it is not required for maintenance. Fourth, if it is not used for a long time, empty the material in the pipeline. Fifth, observe the moisture filter and oil mist device of the pneumatic combination two-piece before going to work every day. Sixth, during the production, we should always patrol and observe the mechanical parts to see if the rotation and lifting are normal if there is any abnormality, and if the screws are loose. Seventh, do a good job of cleaning and sanitation, keep the surface of the Tube Filling machine And Sealing machine clean, often remove the accumulation on the scale body, and pay attention to keeping the electric control cabinet clean.
Wenzhou Zungwan Intelligent Machine Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream, ointment, fluid, and semi-fluid materials. If you are engaged in work related to Tube Filling machine And Sealing machine or want to know more about our company, you can contact us. Our official website is https:// www.cnzpack.com/.
Korea East Asia Pharmaceutical Company, ordered a syrup filling line from our company, from bottle management - bottle washing - filling - corking - capping - labeling, the whole line in the Korean factory to complete the commissioning task, the whole line production design speed of 120 bottles per minute high-speed filling line.
Capping Machine operation, accuracy error, installation adjustment, equipment cleaning, maintenance, and other aspects are very simple and convenient. Capping Machine has been widely used in various industries such as daily chemical and grease, and can fill different high-viscosity fluids. So what are the working principles and structural characteristics of the Capping Machine? Let's take a look together next.
This is the content list:
l How Capping Machine works
l Structural characteristics of Capping Machine
How Capping Machine works
The Capping Machine adopts a new horizontal design, which is light and convenient and can automatically pump the material. For thicker slurry, a hopper can be added. When the Capping Machine is in the "auto" state, the Capping Machine will automatically perform continuous filling at a set speed. Capping Machines can be divided into three types: atmospheric filling machine, vacuum filling machine, and pressure filling machine.
Under normal pressure, Capping Machine can fill the liquid in a self-flowing manner according to the weight of the liquid itself. The filling method is to fill at a pressure greater than atmospheric pressure. The pressure in the liquid storage tank is greater than the pressure in the bottle, and the liquid that needs to be filled will enter the bottle depending on the pressure difference. The key component of the Capping Machine is the PLC operation control system. Under normal pressure, Capping Machine can fill the liquid in a self-flowing manner according to the weight of the liquid itself. The filling method is to fill at a pressure greater than atmospheric pressure. The pressure in the liquid storage tank is greater than the pressure in the bottle, and the liquid that needs to be filled will enter the bottle depending on the pressure difference. The key component of the Capping Machine is the PLC operation control system.
The principle of the Capping Machine is relatively easy to understand. The improved control system simplifies the structure of the machine. It can be seen from the operating conditions and control efficacy tests of the actual application that the automation level of the system has reached the design requirements. This reduces the labor intensity of the operator and makes the production line that needs filling production about 30% higher than before, so the probability of failure of the Capping Machine is significantly reduced.
Structural characteristics of Capping Machine
The design of the Capping Machine is very reasonable and appropriate, the remainder of the machine is very small, and the operation and use are very simple. The pneumatic parts inside the Capping Machine all use new pneumatic components. The piston and cylinder of the Capping Machine cylinder are made of polytetrafluoroethylene and stainless steel to meet the requirements of GMP testing. The filling quantity and filling speed of the Capping Machine can be adjusted at will, and the degree is relatively high.
The Capping Machine can be modified according to actual production needs. It can be transformed into a multi-head system, explosion-proof system, and overflow system. The Capping Machine is suitable for use in food, daily necessities, pesticides, and other industries, and has a broad application prospect.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. The company strictly controls the quality of the Capping Machine. If you are interested in Capping Machine, you can contact us, our website is www.cnzpack.com. I look forward to your coming and hope to cooperate with you.
The Cosmetic Filling Machine and Capping machine is a professional cosmetic filling and capping equipment, which can make the cap tighter without damaging the mouth of the bottle and effectively protect the cosmetics from contact with the outside world. Next, let's take a look at the use and maintenance of the Cosmetic Filling machine and the capping machine. Here are some answers.
Here is the content list:
l Instructions for use of Cosmetic Filling machine And Capping machine.
l How is the daily maintenance of the Cosmetic Filling machine And Capping machine?
Instructions for use of Cosmetic Filling machine And Capping machine.
First, because the Cosmetic Filling Machine and Capping machine is an automated machine, the dimensions of the pop-up bottle, bottle liner, and bottle cap are required to be uniform. Second, before driving, you must first use the crank handle to turn the machine to see if there is any abnormality in the rotation, and then you can drive after it is confirmed that it is normal. Third, when adjusting the machine, the tools should be used appropriately. It is strictly forbidden to use excessive tools or excessive force to dismantle the parts to avoid damage to the machine parts or affect the performance of the machine. Fourth, the Cosmetic Filling machine and the Capping machine must be kept clean. Before the shift, all parts of the machine surface should be cleaned once, and clean lubricating oil should be added to each activity department. It should be scrubbed once a week, especially the areas that are not easily cleaned in normal use or blown with compressed air.
How is the daily maintenance of the Cosmetic Filling machine And Capping machine?
First, the Cosmetic Filling Machine and the Capping machine has strict requirements for the placement environment and must ensure the indoor humidity is moderate, ventilated, and hygienic. Because the Cosmetic Filling Machine and Capping machine is a mechanical device, after all, the raw materials are some steel electromechanical, etc. It is easy to rust when placed in a humid environment, and a closed environment is not conducive to the heat dissipation of the equipment during operation. Second, you must ensure that the power supply is normal and the grounding wire is safe before use. Voltage instability can cause considerable damage to the machine. Third, the non-woven soft cloth and cleaning agent must be added to wipe off the oil or dirt and wipe dry before the Cosmetic Filling machine and capping machine are operated. After use, take out all the remaining materials to prevent the materials from corroding the equipment and scrub them clean. Periodically clean the invisible dust and garbage in the chassis. And adhere to the tightness of the mechanical parts. Fourth, clean up the machine regularly. Many companies conduct major maintenance on machinery and equipment once a year in autumn. Fifth, add lubricating oil to the mechanical components of the Cosmetic Filling machine and Capping machine regularly to reduce frictional resistance and make the machine run faster.
Our official website is https:// www.cnzpack.com/. If you are engaged in work related to Cosmetic Filling machines and Capping machines or want to learn more about our company, you can communicate with us on the website.
They ordered two hand sanitizer filling lines, requiring a speed of 150 bottles per minute, from automatic bottle management - automatic filling - automatic cap management - automatic capping - automatic labeling.
The whole production line was designed, developed and produced by our company, and it took 70 days from the finalization of the contract to delivery. Because of the outbreak of New Crown epidemic in the U.S., we completed the delivery of the equipment ahead of schedule and flew it to the U.S.
Capping Machine is filling equipment specially designed for new oral liquid easy-pull bottles. The design is reasonable, the structure is simple, the operation is convenient, and a mechanical stop filling device is provided for lack of bottles. So what are the adjustment methods of the Capping Machine? Let's take a look together next.
This is the content list:
l Capping Machine feeding half adjustment
l Matters needing attention in discharging
l Adjustment of the locking device
l Vibrator adjustment
Capping Machine feeding half adjustment
Adjust the bottle blocking plate on the feeding half of the Capping Machine upwards to shorten the adaptation to the bottle feeding stroke. Adjust downwards to make the Capping Machine adapt to the extension of the bottle feeding stroke. Adjust the positioning bottle position left and right to align the bottle position when the movable tooth is running, so that the bottle can be fed into the positioning tooth smoothly. Adjust the bottle blocking plate of the Capping Machine so that the width of the bottle inlet is about 22 mm.
Adjust the perfusion Capping Machine component. The role of the perfusion Capping Machine component is to make the liquid medicine be delivered to each easy-pull bottle in time through the dosing device, one-way valve, and needle. Therefore, the needle must enter the bottle mouth properly and the filling time must be appropriate. Adjust the Capping Machine side cam to rotate clockwise or counterclockwise so that the needle is inserted into the bottle mouth just after the empty bottle enters the toothed position. And lift the needle before leaving the toothed position. The filling time of the Capping Machine is adjusted. Turn the cam clockwise or reverse the adjustable needle into the bottle mouth and start filling immediately, and stop filling before the needle leaves the bottle mouth.
Matters needing attention in discharging
Since the Capping Machine is an easy-pull bottle filling and locking device, the discharging has been capped and sealed. To prevent the locked bottle from overturning, it must be placed on the Capping Machine discharge hopper before the first bottle is discharged. Several empty bottles can be transported to the discharge hopper smoothly to keep the locked bottles and sent to the next process with the bottle hopper.
Adjustment of the locking device
Capping Machine capping time adjustment, adjust the cam rotation angle. When the filling liquid bottle enters the locking tooth position, the locking shaft has moved and left the bottle cap before the moving tooth approaches the bottle. The capping pressure is adjusted, and the capping pressure is adjusted. The size of the cap pressure is directly related to the quality of the lock. If the pressure is too high to break the easy-pull bottle, and the pressure is too small, it will affect the sealing performance. Therefore, the nut should be adjusted according to the actual average height of the easy-pull bottle to adjust the pressure to the best.
Capping Machine blade action time adjustment, the blade should be close to the bottleneck before the end of the capping, otherwise, the locking effect of some short bottles cannot be achieved. Loosen the nut during adjustment, and adjust the shaft and up and down to make the blade action time sooner or later. When adjusting the lock of the Capping Machine, pay attention to the locking of the nuts after the adjustment of each department. The easy-pull bottle must be used for the initial valve test. The average height must be taken. Irregular easy-pull bottles cannot enter the lock to avoid damage to the parts.
Vibrator adjustment
The Capping Machine adopts the principle of electromagnetic oscillation to drop the bottle cap to the proper position along the track according to a certain movement trajectory. The vibrator is packaged separately when it leaves the factory, and the lower rail opening must be aligned with the movement rail of the easy-pull bottle when installed. To adjust the gap between the magnets of the Capping Machine, loosen the screw, open the cover, adjust the nut, and make the vibration of the Capping Machine low and fast.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It strictly controls the production of the Capping Machine. A large number of factory tests are carried out before Capping Machine leaves the factory to ensure product quality. If you are interested in Capping Machine, you can Contact Us, our website is www.cnzpack.com.
After we purchase Pharmaceutical Filler and Capper, we need to install and debug Pharmaceutical Filler and Capper. Let's take a look at it together next.
This is the content list:
l Installation of Pharmaceutical Filler and Capper
l Commissioning of Pharmaceutical Filler and Capper
l Maintenance of Pharmaceutical Filler and Capper
Installation of Pharmaceutical Filler and Capper
According to different models and specifications of Pharmaceutical Filler and Capper, refer to the random manual for installation.
For small-sized Pharmaceutical Filler and Capper, it is not required to build the foundation, just install it on the flat workshop floor, make a good horizontal reference, adjust the elevation of incoming and outgoing chain belt according to the layout diagram, and adjust the legs to make the load of the whole machine evenly distributed.
For large-sized Pharmaceutical Filler and Capper, it is necessary to build a solid installation foundation as required. When installing, the horizontal benchmark should be played, especially when it is connected with the capping machine, the two parts of the incoming and outgoing bottle belts must be at the same horizontal benchmark.
To ensure the smooth bottle delivery of Pharmaceutical Filler and Capper, the inlet pallet under the inlet star wheel should be 0.5mm higher than the surface of the bottle tray, and the outlet pallet under the middle star wheel should be 0.5mm lower than the surface of the bottle tray. The running is free and there should be no jamming interference. The horizontal part of the liquid inlet pipe should have a certain slope to facilitate emptying and air discharge. Make sure the bearing load of Pharmaceutical Filler and Capper's legs is even. Matching equipment with the host, such as gas-liquid control box, vacuum pump system and electric control box, etc. are generally installed separately.
Commissioning of Pharmaceutical Filler and Capper
After confirming the installation of Pharmaceutical Filler and Capper is completed, the commissioning of Pharmaceutical Filler and Capper can be carried out step by step as follows. Replace suitable accessories according to the bottle type filled by Pharmaceutical Filler and Capper, and adjust the parts, including the inlet screw, guide bar spacing, side guard safety switch, star-shaped paddle wheel, reservoir, and capping head height adjustment, etc. Thoroughly clean the Pharmaceutical Filler and Capper reservoir, liquid piping, and gas piping to ensure that there is no foreign material. Make a hydraulic test on the storage tank and pipeline at the same time. Check carefully whether the wiring of the Pharmaceutical Filler and Capper control box is correct, and turn on the main switch only after the equipment is turned manually without jamming. Start the equipment in a pointing way to check if there is any abnormality. Start the Pharmaceutical Filler and Capper at low speed and check the starting, braking, emergency stop, and speed regulation performance. Then infuse an empty bottle at low speed, check whether it can pass through the bottle feed screw, guide bar, and star wheel smoothly and whether each control touch block can respond sensitively. Check whether the Pharmaceutical Filler and Capper can drop the cap smoothly and seal the cap tightly. After that, adjust the value of each instrument on the liquid and gas control cabinet according to the filing requirements of Pharmaceutical Filler and Capper. Check the liquid level and pressure of Pharmaceutical Filler and Capper reservoir, make filling test, adjust the filling head and control the bottling level.
Maintenance of Pharmaceutical Filler and Capper
Pharmaceutical Filler and Capper in the process of use, must be required to carry out regular maintenance. First of all, we must ensure that the lubrication status of the Pharmaceutical Filler and Capper must be good, and the lubrication points must be well-lubricated in time to maintain the oil level of each tank and the intact spray lubrication function. Timely replacement of a variety of damaged parts, such as seals, bottle transport parts, and transmission parts in the wearing parts. The movable parts that are not adjusted for a long time, such as the reservoir of Pharmaceutical Filler and Capper and the height adjustment device of the capping machine, should be run regularly to avoid rust and corrosion. Regularly and regularly clean the liquid tank of Pharmaceutical Filler and Capper, liquid delivery tube, filling valve, and parts that may contact with liquid as required. Liquid residue, oil, water, and glass fragments should be removed to keep the equipment neat and hygienic. Since there are many models and specifications of Pharmaceutical Filler and Capper, and the performance, structure, and working principle vary greatly, operators and maintenance personnel should use and maintain them according to the operation manuals accompanying each machine.
Our products are in great demand in both domestic and international markets, and we are committed to improving and developing to meet our customers and the market demand is our eternal theme and sincere commitment to our customers. If you are interested in Pharmaceutical Filler and Capper, you can contact us, our website is www.cnzpack.com.
Cosmetic Filling Machine And Capping machine is very simple and convenient in operation, accuracy error, installation adjustment, equipment cleaning, maintenance, etc. Next, let’s take a look at the introduction of the Cosmetic Filling machine And Capping machine. Here are some answers.
Here is the content list:
l Information about Cosmetic Filling machine And Capping machine.
l Attention to the installation of Cosmetic Filling machine And Capping machine.
l What are the safety rules of Cosmetic Filling machines And Capping machines?
Information about Cosmetic Filling machine And Capping machine.
The Cosmetic Filling machine And Capping machine integrates light, machine, electricity, and pneumatics, with a high degree of automation, high yield, wide adaptability, and good stability. The Cosmetic Filling machine And Capping machine adopts PLC control, which is easy to operate and easy to adjust. Due to its high technical content and good quality, it is an ideal piece of equipment for perfume manufacturers! Cosmetic Filling Machine And Capping machine is mainly suitable for different material specifications and different specifications of caps, screw (rolling) caps. The structure is compact and reasonable, and it can be easily linked with other equipment into a line. The dust cover can be purchased. The machine is of linear design and the assembly line is convenient and beautiful.
Attention to the installation of Cosmetic Filling machine And Capping machine.
First, after unpacking the Cosmetic Filling machine And Capping machine, first check whether the random technical information is complete and whether the machine is damaged during transportation, to solve it in time. Second, install and adjust the feeding component and the discharging component according to the outline diagram in this manual. Third, add new lubricating oil to each lubrication point. Fourth, use the crank handle to turn the machine to check whether the Cosmetic Filling machine And Capping Machine is running in the correct direction, and the machine must be grounded.
What are the safety rules of Cosmetic Filling machines And Capping machines?
First, check the Cosmetic Filling machine And Capping machine equipment for foreign matter, such as residual liquid material or other stones, iron pieces, and other garbage, and clean it up in time. Second, do not clean the motor with water or other liquids. Third, you cannot use tools or other irrelevant things to contact the Cosmetic Filling Machine And Capping Machine. Fourth, wear gloves, glasses, and work clothes when cleaning the machine. Non-professional operators cannot approach the Cosmetic Filling machine And Capping Machine.
Wenzhou Zongwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously develops various liquid, powder, cream, ointment, fluid, and semi-fluid material packaging machinery. If you are engaged in work related to Cosmetic Filling machines And Capping machines or want to learn more about our company, you can communicate with us on the website. Our official website is https:// www.cnzpack.com/. Our company adheres to the corporate culture of "quality first, customer first", and has always made unremitting efforts to become a professional supplier of Cosmetic Filling machines And Capping machines in the industry.