











In our production and life, the Liquid Filling Machine has a significant impact on many industries, so what is the method of using the Liquid Filling Machine? Let's go take a look next.
This is the content list:
l The ground wire must be well-grounded before the Liquid Filling Machine works
l Liquid Filling Machine liquid filling system assembly
The ground wire must be well-grounded before the Liquid Filling Machine works.
The ground wire must be well-grounded before the Liquid Filling Machine works, and then the appropriate standard syringe must be selected according to the different filling volumes. Generally, a 1ml syringe is used when the dispensing range is 0.2-1ml. Use a 5ml syringe for 1-5ml.use a 10ml syringe for 5-10ml. The 20ml model uses a 20ml glass infusion device. The 100ml model uses a 100ml glass infusion device, and the 500ml model uses the stainless steel filling system produced by our factory.
Liquid Filling Machine liquid filling system assembly
Pull out the inner core of the Liquid Filling Machine syringe, put the screw sleeve on the inner core of the syringe, and use the screw sleeve to properly fasten it to the lower base (cleanliness must be paid when disassembling the syringe). Place the upper clamp seat on the outlet end of the Liquid Filling Machine syringe jacket, and properly tighten the nuts on both sides to assemble the inner core and outer jacket of the installed Liquid Filling Machine syringe into one body. At this point, the Liquid Filling Machine injection system is assembled.
Place the Liquid Filling Machine valve with the arrow facing upwards and the arrow mark facing outwards and fix it on the fixing screw with a nut. Assemble the Liquid Filling Machine with a complete liquid filling system, align the upper and lower round holes of the liquid filling system components with the upper and lower fixing rods respectively, and put them on the bearing so that the outer end surface and the bearing surface are levels. When assembling the lower end, do not make the screw sleeve and the crank touch to prevent abnormal noise when the crank on the Liquid Filling Machine rotates (the screw sleeve and the crank are about 1mm apart when installed correctly). After the liquid filling system is installed correctly, tighten it. Tighten the screws up and down. Use a short hose to connect the Liquid Filling Machine syringe to the valve connection nozzle. The liquid inlet pipe is connected to the water inlet, and the liquid outlet pipe is connected to the water outlet. To prevent the liquid inlet and outlet pipes from being entangled, clip the liquid inlet and outlet pipes into the ear openings on the side of the casing.
Turn the crank of the Liquid Filling Machine by hand, it should be able to rotate freely, otherwise, the assembly is wrong, you should check whether the Liquid Filling Machine injection system is fastened to the rotating bearing.
Our company has obtained more than 20 invention patents and utility model patents. The main products are a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and online capping machine, capping machine and labeling machine, bottle unscrambler, tube filling and sealing machine, Cartoning machines, and other packaging equipment. If you are interested in Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.
Tube Filling machine And Sealing machine adopt the latest module circuit, stable working performance, high efficiency, and all components adopt famous brand products. Under the careful design of our company, various advanced Tube Filling Machine And Sealing machines have been produced. Mainly used for sealing toothpaste, cosmetics, medicine, food, industrial products, and various hoses. Next, let's take a look at the cleaning and maintenance of the Tube Filling machine And Sealing machine. Here are some answers.
Here is the content list:
Tube Filling machine And Sealing machine cleaning.
Daily maintenance of Tube Filling machine And Sealing machine.
First, regularly clean the surface of the Tube Filling machine And Sealing machine, the bottom plate and the lower mold slide plate, grooves, the upper mold inner pressure plate, and the positioning rod. Second, grease should be added to the transmission parts of the lower mold slide plate, pressing rod bearing, eccentric wheel and guidepost, guide rail, and so on regularly to ensure the performance of the Tube Filling Machine And Sealing machine. Third, the method of cleaning the toothed knife: first plug the two drain holes of the lower mold with a cotton ball, pour boiling water into the groove of the lower mold, until it is full, then push the slide of the lower mold into place, and lower the upper mold. Press to the lowest point, let the toothed knife soak for a few minutes until it is clean, repeat several times.
First, check the equipment ground wire frequently to ensure reliable contact; clean the weighing platform frequently; check whether the pneumatic pipeline is leaking and whether the air pipe is broken. Second, change the lubricating oil of the reducer motor every year, check the tightness of the chain, and adjust the tension in time. Third, the sensor of the Tube Filling Machine And Sealing machine is a high-precision, high-sealing, and high-sensitivity device. Impact and overload are strictly prohibited, and no contact is allowed during the working process, and it is not allowed to be disassembled if it is not required for maintenance. Fourth, if it is not used for a long time, empty the material in the pipeline. Fifth, observe the moisture filter and oil mist device of the pneumatic combination two-piece before going to work every day. Sixth, during the production, we should always patrol and observe the mechanical parts to see if the rotation and lifting are normal if there is any abnormality, and if the screws are loose. Seventh, do a good job of cleaning and sanitation, keep the surface of the Tube Filling machine And Sealing machine clean, often remove the accumulation on the scale body, and pay attention to keeping the electric control cabinet clean.
Wenzhou Zungwan Intelligent Machine Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream, ointment, fluid, and semi-fluid materials. If you are engaged in work related to Tube Filling machine And Sealing machine or want to know more about our company, you can contact us. Our official website is https:// www.cnzpack.com/.
Pharmaceutical Filler and Capper, whether semi-automatic or fully automatic, will encounter more or less in the process of using different places of failure, in the face of Pharmaceutical Filler and Capper's special parts of the failure, how do we find the problem as soon as possible and solve it? Let's take a look at it.
This is the content list:
l Pharmaceutical Filler and Capper's PLC failure
l Pharmaceutical Filler and Capper's Magnetic Switch Failure
l Pharmaceutical Filler and Capper solenoid valve failure
Pharmaceutical Filler and Capper PLC Failure
If the point controls Pharmaceutical Filler and Capper, the fault phenomenon is that the motor runs after the signal start Pharmaceutical Filler and Capper, but the motor does not stop running after the stop signal is issued. And Capper only stops running when the PLC is powered down. If the point controls the solenoid valve. The fault phenomenon is that the solenoid valve coil is not energized, and the cylinder is not reset. If the PLC of Pharmaceutical Filler and Capper is hit with external force to make the sticking point separate, it can assist to determine the fault of Pharmaceutical Filler and Capper.
Pharmaceutical Filler and Capper's magnetic switch failure
Pharmaceutical Filler and Capper's magnetic switch is used to detecting the position of the cylinder and control the cylinder travel. The four cylinders of laminating, pushing, pressing, and fusing knife are interrelated, and the magnetic switch is used to detect and control their positions. Pharmaceutical Filler and Capper failure is mainly manifested as the subsequent cylinders do not move, because the cylinder speed of Pharmaceutical Filler and Capper is faster, which causes the magnetic switch cannot detect the signal. Such as pushing the package cylinder speed is too fast, after pushing the package reset, the pressure package and fusion knife cylinder do not move.
Solenoid valve failure of Pharmaceutical Filler and Capper
Pharmaceutical Filler and Capper solenoid valve failure is mainly manifested as the cylinder does not move or does not reset, the reason is that Pharmaceutical Filler and Capper cylinder solenoid valve cannot change direction or tampering air. If the solenoid valve falters, the air pressure of Pharmaceutical Filler and Capper can't reach the working pressure because the inlet and outlet air paths are connected, and the knife beam doesn't rise to the place. the proximity switch of Pharmaceutical Filler and Capper knife beam protection doesn't work, and the precondition of full machine operation is not established. Pharmaceutical Filler and Capper does not operate, which is easily confused with an electrical fault. Solenoid valve air leakage sound, listen carefully to the source of sound and hand search for air leakage points, generally can easily identify the air leakage solenoid valve.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, with first-class product quality and efficient and fast after-sales service, forging the excellent products of "Central". Pharmaceutical Filler and Capper will undergo a lot of product testing before leaving the factory to reduce the probability of failure of Pharmaceutical Filler and Capper, and also provide customers with high-quality Pharmaceutical Filler and Capper warranty service. If you are interested in Pharmaceutical Filler and Capper, you can contact us, our website is www.cnzpack.com.
The Tube Filling machine And Sealing machine, as its name implies, is a machine that can be filled and sealed. There are different models for different industries. The more commonly used industries are chemicals, food, etc. Next, let's take a look at the introduction of the Tube Filling machine And Sealing machine. Here are some answers.
Here is the content list:
l Basic information of Tube Filling machine And Sealing machine
l Application performance of Tube Filling machine And Sealing machine.
l The main characteristics of the Tube Filling machine And Sealing machine.
Basic information of Tube Filling machine And Sealing machine
Tube Filling machine And Sealing machine adopts closed and semi-closed filling pastes and liquids. The seal has no leakage. The filling weight and volume are consistent. Filling, sealing, and printing can be completed at one time. It is suitable for medicine, daily chemicals, and food. Chemical and other fields of product packaging. Such as: filling and sealing of materials such as piping, ointment, hair dye, toothpaste, shoe polish, adhesive, AB glue, epoxy glue, neoprene, and other materials. Tube Filling machine And Sealing machine is an ideal, practical, and economical filling equipment for pharmaceutical, daily chemical, fine chemical, and other industries.
Application performance of Tube Filling machine And Sealing machine.
First, the transmission part of the Tube Filling machine And Sealing machine is enclosed under the platform, which is safe, reliable, and pollution-free. Second, the filling and sealing part is installed in a semi-closed non-static outer frame visible cover above the platform, which is easy to observe, operate and maintain. PLC control, man-machine dialogue interface. The rotary table is driven by a cam, with fast speed and high precision. Third, in the inclined-hung tube warehouse, the upper tube mechanism is equipped with a vacuum adsorption device, to ensure that the automatic upper tube accurately enters the tube seat. The photoelectric benchmarking workstation uses high-precision probes, stepping motors, etc. To control the hose pattern in the correct position. Fourth, the filling nozzle of the Tube Filling Machine And Sealing machine is equipped with a material cut-off mechanism to ensure the filling quality. No tube no filling. Fifth, the tail sealing adopts internal heating at the end of the tube, and external cooling and cooling devices; the typing workstation automatically prints the word code on the position required by the process. Sixth, fault protection alarm, no tube alarm, door open shutdown, overload shutdown; counting, and quantitative shutdown.
The main characteristics of the Tube Filling machine And Sealing machine.
First, the Tube Filling machine And Sealing machine has a compact design, easy to operate and adjust. Second, the driving part is fully enclosed. Third. The Tube Filling Machine And Sealing machine is a pneumatic tube washing and feeding machine with an intelligent temperature control cooling system. Fourth, the 316L stainless steel contacts comply with GMP standards. Fifth, the Tube Filling machine And Sealing machine provides overload protection. Sixth, the safety interlock is closed when the door is opened. Seventh, the automated workflow from tube installation to finished product output. Eighth, photoelectric induction automatic orientation.
If you want to buy Tube Filling machine And Sealing machine or want to know more about our company, you can communicate with us on the website. Our official website is http:// www.cnzpack.com/.
Cartoning machine is the description of automatic loading of medicine bottles, trays, ointments, etc. into folded cartons and completing the capping action. Some Cartoning machines with stronger functions also have functions such as sealing labels or heat shrink packaging. So what are the considerations for the daily maintenance of the Cartoning machine? Let's take a look together next.
This is the content list:
l Comply with safe operating procedures
l Refuel or change the oil on time
l Be organized
l Clean inside and outside of equipment
Comply with safe operating procedures
Comply with the Cartoning machine's safety operating procedures and do not overload the equipment. The Cartoning machine's safety protection devices are complete and reliable, and unsafe factors are eliminated in time. For example: Do not touch the inverter within 5 minutes after the power of the Cartoning machine is cut off because it will have a relatively high residual voltage, which will be released after a few minutes. After the Cartoning machine work is finished, you should do a good job of cleaning, use a brush to remove all unclean things, and check whether the power is turned off.
Refuel or change the oil on time
Cartoning machine is well lubricated, add oil or change oil on time, keep oiling, no dry friction. The Cartoning machine should be refueled before starting up. Where there is reciprocating motion, add oil, twice a day, 5-6 drops each time. Add butter once a month to the bearings of the rotating part on both sides of the folding machine. Grease the sliding part of the tongue guide once a week.
Be organized
Cartoning machine tools, accessories, and workpieces (products) should be neatly arranged, Cartoning machine pipes and lines should be organized.
Equipment interior and exterior clean
The interior and exterior of the Cartoning machine equipment should be clean and tidy. All sliding surfaces, lead screws, rack and pinion, gearbox, oil holes, etc. are free of oil and dirt, and all parts of the Cartoning machine do not leak oil or air. The debris, debris, and dirt around the equipment should be cleaned up. For example, there should be no foreign objects in the main motor of the Cartoning machine, the casing should be kept clean, the cooling fan should be good, and it should be maintained regularly. Cartoning machine photoelectric switch and proximity switch detection surface should not have foreign matter and pollution, otherwise, it will cause malfunction. The detection distance should be properly adjusted, and the bracket should be kept tight and not loose to avoid damage when the machine is running. The electrical components inside and outside the electrical cabinet of the Cartoning machine must be kept clean and well dissipated.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It will test the Cartoning machine before leaving the factory and provide warranty service. If you are interested in Cartoning machine, you can contact us. Our website is www.cnzpack.com. I look forward to your coming and hope to cooperate with you.
Liquid Filling Machine is a kind of process machinery, its process characteristics are more obvious, for the design requirements provided by the customer as well as the functions, work efficiency and other aspects of good, then Liquid Filling Machine what are the design principles and considerations? Let's learn about it together.
This is the content list:
l The design principle of Liquid Filling Machine
l Precautions for Liquid Filling Machine
The design principle of Liquid Filling Machine
First, design the parameters of the Liquid Filling Machine and the material to be filled, and then also to understand the container to be filled, to understand the shape of the container and the characteristics of the container cap, according to these characteristics design the corresponding bottle Liquid Filling Machine.
Secondly, we should also know the functions to be achieved by the Liquid Filling Machine, the principle and method of Liquid Filling Machine filling, the whole process of Liquid Filling Machine filling should be carefully understood, and each link should be designed reasonably and appropriately to avoid affecting the effect of filling.
Liquid Filling Machine should also be based on the specific needs of enterprises, the use of functional principles of innovative design methods to design filling equipment to meet the production needs of enterprises, which will not only improve efficiency but also reduce the rate of damage and reduce the production costs of enterprises.
Precautions for Liquid Filling Machine
First, check the Liquid Filling Machine itself to determine if the ball valve in the filling machine is damaged or loose. If the internal ball valve of the Liquid Filling Machine is the cause, the solution is to replace the internal ball valve. If the internal ball valve of the Liquid Filling Machine is damaged, there is no way to repair it, only to replace it with a new one.
Check that the Liquid Filling Machine syringe assembly is clean. If it is not clean, it will cause an unclean blockage between the inner and outer tubes, so remove the Liquid Filling Machine syringe, clean it and disinfect and maintain it.
Check that the Liquid Filling Machine filler nozzle is complete. If the Liquid Filling Machine filling nozzle is damaged, the equipment will leak during operation. Replace broken filling nozzles and inspect other filling nozzles for use, deterioration, or corrosion, and replace them as soon as possible.
Check whether the O-ring is corroded or worn. If the O-ring is corroded or worn, it will also cause the Liquid Filling Machine to drip. Therefore, in this case, it is recommended to replace the O-ring.
Check the Liquid Filling Machine barrel position. Determine if the cylinder is in the cylinder center support position, and also check if the Liquid Filling Machine cylinder piston and piston rod are secure, and if they are loose, please lock them. If the cylinder failure position is changed, you need to reinstall the cylinder and confirm the correct position.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, which has made great achievements in Liquid Filling Machine and is loved by the consumers. If you are interested in Liquid Filling Machine, you can contact us, our website is www.cnzpack.com.
In our daily life, Capping Machine plays a vital role for us, so what are the main work processes and precautions of the Capping Machine? Let's take a look together next.
This is the content list:
The main workflow of Capping Machine
How to carry out daily maintenance and maintenance of Capping Machine
How to deal with common problems of Capping Machine
We know that after the plastic bottles are sorted by the Capping Machine, they enter the conveyor chain in a single row. In the filling station, the plunger pump injects the liquid in the container into the plastic bottle. After filling, the plastic bottle enters the index plate and stops accurately at the capping station. Manually place the cap of the Capping Machine at the entrance of the friction beltline, take out the capping claw, screw the cap claw, and squeeze the tube claw to complete the capping action. Then the plastic bottle exits the index plate and enters the conveyor chain, and enters the labeling station to complete the round bottle labeling.
1. Always keep the Capping Machine clean, especially for the electrical appliances on the switchboard, to prevent moisture and dust, and it is forbidden to change the program of the inverter and the program controller at will.
2. The power supply voltage of the Capping Machine should be stable, not exceeding ±15%, the material temperature should be kept at 10℃-40℃, the ambient temperature should be kept at 5℃~40℃, and the temperature should be kept at 5~95%PH.
3. The flowmeter used by the Capping Machine for spray filling is a precision instrument. Therefore, the oil must be precision filtered before it can be filled.
4. Turn off the power supply and oil inlet valve of the Capping Machine after finishing the work.
5. Pay attention to the cleanliness of the infrared sensor from the Capping Machine. Frequently wipe it clean with clean cotton. It is strictly forbidden for any object to approach the sensor during the working process, and strong light should not be directly or reflected on the sensor, otherwise, it will prosper and malfunction.
6. Add cylinder lubricating oil to the pneumatic triplet regularly.
7. When the machine is not used for a long time, all parts should be wiped clean and covered with plastic or tarpaulin to prevent dust.
First, what should I do if the cylinder piston of the Capping Machine does not work? Confirm whether the safety emergency stop switch is safe. Confirm that the air supply switch of the Capping Machine is turned on. Check if the Capping Machine one-way signal valve is damaged.
Second, what should I do if the Capping Machine cylinder piston does not return after being pushed to the top? Confirm whether the moving target is in contact with the one-way valve.
Third, how to adjust the filling volume of the Capping Machine is inaccurate or not discharged?
Check whether the upper and lower throttle valves of the Capping Machine are closed, and increase the pumping speed of the throttle valve of the cylinder. Make sure that the Capping Machine quick-install tee is locked with a clamp. Confirm whether there are enough materials in the Capping Machine storage box. Make sure that the joints of the pipes of the Capping Machine are sealed.
Fourth, what should I do if the material of the Capping Machine flows out from the rear end of the cylinder? Check whether the sealing ring on the Capping Machine piston is worn. If it is worn, replace it and make sure that the piston and the piston rod are tight.
In addition to timely handling of problems, it is also necessary to do a good job of preventive work in advance. Doing a good job in daily maintenance can also reduce the failure rate of the Capping Machine. The daily maintenance and maintenance of the Capping Machine cannot be underestimated. This is a very important step. Daily maintenance on time can effectively extend the service life of the Capping Machine, improve the production efficiency of the enterprise, and keep Capping Machine in normal operation throughout the day, reducing manpower. The loss of material resources.
Wenzhou Zungwan Intelligent Machinery Co., Ltd.'s first-class product quality and efficient and quick after-sales service have created excellent products of "Zhonghuan". Products are in great demand in the domestic and foreign markets. Keep improving, develop to satisfy customers, and meet market demands are our eternal topic and our sincere commitment to customers. Therefore, Capping Machine is very popular among consumers. If you are interested in Capping Machine, you can contact us. Our website is www.cnzpack.com.
The tube Filling machine And the Sealing machine are determined by multiple parameters. It is impossible to describe a Tube Filling machine And Sealing machine with any single parameter. Shaft power, blade displacement, pressure head, blade diameter, and filling speed are the five basic parameters that describe a Tube Filling Machine And Sealing machine. So, let's take a look at the principle of the Tube Filling machine And Sealing machine together. Here are some answers.
Here is the content list:
l Basic parameters.
l The shear rate of the fluid.
l Small slot and big slot.
Basic parameters.
The displacement of the blade is proportional to the flow rate of the blade itself, the first power of the blade speed, and the third power of the blade diameter. The shaft power consumed by the filling is proportional to the specific gravity of the fluid, the power standard of the blade itself, the third power of the speed, and the fifth power of the blade diameter. In the case of a certain power and blade form, the blade displacement and pressure head can be adjusted by changing the diameter of the blade and the matching of the speed. That is, the large diameter blade is equipped with a low-speed Tube Filling machine And a Sealing machine. High flow effect and low-pressure head, while the small diameter blade with high speed produces a higher pressure head and lower flow effect.
The shear rate of the fluid.
In the filling tank, the only way to make the micelles collide with each other is to provide a sufficient shear rate. According to the mechanism of the Tube Filling Machine And Sealing machine, it is because of the existence of fluid velocity difference that the fluid layers are mixed. Therefore, where the filling process always involves the fluid shear rate lhhaha620. Shear stress is a force that is the real cause of bubble dispersion and droplet breaking in filling applications. It must be pointed out that the shear rate at each point of the fluid in the entire stirred tank is not the same.
Small slot and big slot.
Experimental research shows that, as far as the blade area is concerned, no matter what type of blade, when the diameter of the blade is constant, the maximum shear rate and the average shear rate increase with the increase of the speed. However, when the rotation speed is constant, the relationship between the maximum shear rate and the average shear rate, and the diameter of the blade is related to the slurry type. When the rotation speed is constant, the maximum shear rate of the radial blade increases with the increase of the blade diameter, and the average shear rate has nothing to do with the diameter of the blade. These concepts about the shear rate of the blade area require special care in the design of the Tube Filling Machine And Sealing machine to reduce and enlarge. Because the small groove is compared with the large groove, the small groove Tube Filling Machine and Sealing machine often has the characteristics of high speed, small blade diameter, and low tip speed. The large groove Tube Filling Machine And Sealing machine often has the characteristics of low speed, large blade diameter, and high tip speed.
Our official website is https:// www.cnzpack.com/. If you are engaged in work related to the Tube Filling machine And Sealing machine, you can communicate with us on the website.