Mosquito Repellent Capping Machine factory- China Manufacturers Factory Suppliers

In our production and life, Capping Machine is also called a Capping Machine, Capping Machine, or Capping Machine, which is used for screwing and unscrewing the caps of plastic bottles and glass bottles (molded bottles or tube bottles). equipment. Capping Machine is highly intelligent capping equipment with advanced technology, unique design, and easy operation. During the entire capping process, workers only need to place the cap on the mouth of the bottle, and then the bottle is automatically sent to the capping wheel and automatically tightened to complete the capping operation. The Capping Machine evacuates the packaging bottle and then tightens it, which prolongs the storage time of the packaging, reduces the failure rate of the Capping Machine, and improves the packaging efficiency of the Capping Machine. So what are the matters needing attention when operating Capping Machine correctly? Let's take a look together next.

This is the content list:

l Capping Machine rolling wheel adjustment

l Capping Machine lock wheel adjustment

l Capping Machine cap lock

l Capping Machine height adjustment

Capping Machine rolling wheel adjustment

Place the Capping Machine bottle on the bracket and raise the bracket to the highest point. First, loosen the lock nut to adjust the rolling wheel so that the (sprung) edge of the two Capping Machine rolling wheels is at the threading of the bottle. Click on it, then loosen the lock nut, and then adjust the adjusting screw so that the edges of the two rolling wheels are in contact with the cover, and a little pressure is appropriate, and then tighten the nut.

Capping Machine lock wheel adjustment

Adjust the two Capping Machine locking wheels, first loosen the locking nuts, adjust the locking wheels so that the edges of the two locking wheels are in contact with the lower edge of the bottle cap, a little pressure is appropriate, and then tighten the nuts (Note: Adjust Capping Machine Should be from loose to tight, adjust while pulling the lock).

Capping Machine cap lock

Loosen the top screw, remove the Capping Machine gland head, and then remove the entire Capping Machine lock head, install the appropriate plastic lock head on the cone sleeve, and then adjust the lifting height of the bracket to meet the working requirements.

Capping Machine height adjustment

Start the Capping Machine to lower the bracket to the lowest point, then place the bottle on the bracket, loosen the brake nut, turn the adjusting screw to raise the bracket, and then adjust the appropriate distance between the cap of the Capping Machine and the capping head (generally All are adjusted in place at the factory).

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. We have obtained ISO9001 quality management system certification, and some products have passed CE certification. Our company has obtained more than 20 invention patents and utility model patents. If you are interested in Capping Machine, you can contact us, our website is www.cnzpack.com.

Tube Filling machine And Sealing machine is suitable for filling all kinds of paste and high viscosity fluids, suitable for filling large-diameter plastic pipes and composite pipes, and then the pipe is heated inside, and the batch number and date are printed on the seal. Used in pharmaceutical, food, cosmetics, adhesive, and other industries. Next, let me tell you about the related introduction and features of the Tube Filling machine And Sealing machine. Here are some answers.

Here is the content list:

l The related introduction of Tube Filling machine And Sealing machine.

l Design features of Tube Filling machine And Sealing machine.

l Features of Tube Filling machine And Sealing machine.

The related introduction of Tube Filling machine And Sealing machine.

Tube Filling machine And Sealing machine is a machine that fills the packaging into the container and seals it. After the product is put into the packaging container, to keep the product sealed, maintain product quality, and avoid product loss, the packaging container needs to be sealed. Tube Filling machine And Sealing machine is a machine with a compact design and automatic tube feeding. Tube Filling machine And Sealing machine's tube washing, feeding marking, filling, folding, sealing, coding, and finished product output are all performed by a fully automatic control system. The feeding of the washing pipe adopts a pneumatic method, which is accurate and reliable.

Design features of Tube Filling machine And Sealing machine.

First, the Tube Filling machine And Sealing machine is mechatronics, using multiple-introduction technology, controlled by PLC, and can automatically complete tube feeding, partial color labeling, filling, sealing, and tube outlet at the same time. The machine runs smoothly, is easy to control and size conversion, and is suitable for the production of pasty products. Second, the Tube Filling Machine And the Sealing machine has modern modeling, strong practicability, and high processing value. Third, the Tube Filling Machine And the Sealing machine have a stainless steel volumetric bulldozing syringe and a Teflon piston seal to achieve accurate dosage.

Features of Tube Filling machine And Sealing machine.

Tube Filling machine And Sealing machine is a piece of high-tech equipment successfully developed by introducing foreign advanced technology and combining GMP requirements. It has the characteristics of reasonable structure, complete functions, convenient operation, accurate filling, stable operation, and low noise. Tube Filling machine And Sealing machine adopts PLC controller, from liquid or high-speed material filling to batch number printing (including production date) automatic operation, is cosmetics, pharmaceuticals, food, adhesives and other ALU tubes, plastic tubes and multi-tube filling Ideal equipment for sealing, in line with GMP standards.

Wenzhou Zungwan Intelligent Machine Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream, ointment, fluid, and semi-fluid materials. If you are engaged in work related to Tube Filling machine And Sealing machine or want to know more about our company, you can communicate with us on the website. Our official website is https:// www.cnzpack.com/. Our company adheres to the service tenet of "customer first", and implements the service of honesty and customer first.

Korea East Asia Pharmaceutical Company, ordered a syrup filling line from our company, from bottle management - bottle washing - filling - corking - capping - labeling, the whole line in the Korean factory to complete the commissioning task, the whole line production design speed of 120 bottles per minute high-speed filling line.

Wenzhou Zungwan Intelligent Machine Co.,Ltd. is the professional equipment manufacturer to keep researching and developing the packing machinery for every type of liquid, powder, cream/ointment, fluid and half-fluid etc. materials. We have Obtained ISO9001 quality management system authentication and parts of our products have passed CE authentication. Our company has obtained more than 20 invention patents and utility model patents. The main products range from nail polish filling machine, perfume machine,perfume filling machine, powder serial automatically volume-measuring packing machine and inline capping machine, rotary capping machine and labeling machine, bottle unscrambler , screw capping machine ,tube filling and sealing machine, cartoning machine and other Packaging equipments.

So far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and our service as well as our integrity is acclaimed both in China and abroad. we will carry forward the spirit of "integrated innovation, and perseverance," discipline ourselves to be the first, and provide better and more perfect service for our new and old customers with enthusiasm and a new attitude.

With the increasingly fierce competition in the manufacturing and production of plastic bottles in the food and pharmaceutical industries, Bottle Unscrambler has become more and more solid backing for the food and pharmaceutical plastic bottle markets. So how does it play a role? We will introduce the work process and personnel operation specifications of Bottle Unscrambler. Let's take a look together next.

This is the content list:

• The workflow of Bottle Unscrambler

• Personnel operation specification of Bottle Unscrambler

The workflow of Bottle Unscrambler

The workflow of Bottle Unscrambler is generally as follows: manually put materials into the storage bottle library, the materials in the storage bottle library will be automatically quantified and fed to the turntable at the set speed. The turntable rotates at a high speed to supply the bottles as required, the web wheel The irregular bottles are removed, and the bottle dividing part sends the bottles from the turntable to the bottle unscramble part at a certain speed. The Bottle Unscrambler part of the Bottle Unscrambler clamps the bottles to the working surface of the conveyor through the conveyor belts on both sides, and at the same time sorts the bottles through the bottle turner. The Bottle Unscrambler electronic control system performs real-time monitoring and feedback through the sensors of each part to achieve fully automated operation requirements, and save a lot of labor costs and avoid losses caused by human error factors.

Personnel operation specification of Bottle Unscrambler

To ensure the normal and safe operation of Bottle Unscrambler, there are special operating procedures established for it. Operators and equipment management personnel shall perform standardized operations of Bottle Unscrambler under these procedures. This safe operation specification is commonly used in Bottle Unscramblers, mixers, high-speed automatic Bottle Unscramblers, etc.

1. First check the Bottle Unscrambler's intact, clean, and expiration status identification and the equipment operation record of the shift. If the inspection finds that the Bottle Unscrambler has exceeded the cleaning validity period, it is necessary to further clean the equipment according to the equipment cleaning operation rules and fill in the equipment status identification.

2. Check the Bottle Unscrambler and the Bottle Unscrambler to confirm that there is no foreign matter, and turn the bottle plate and unscrambler to confirm that it can work normally.

3. Turn on the Bottle Unscrambler power switch, check the touch screen and three photoelectric switches. If both are energized, the lack of a bottle alarm will be displayed on the touch screen. When the electric eye is blocked by hand, the screen displays the blocking alarm, and the two photoelectric switches are in a normal state.

4. Turn on the Bottle Unscrambler compressed air, use the bottom of the bottle to shake under the electric eye of the bottle puller, compressed air will be sprayed out, and the equipment can be turned on normally.

To ensure that the various parts of the Bottle Unscrambler can work normally, the formal operation can be divided into five steps: click the host start and lift start on the touch screen respectively, and observe whether the Bottle Unscrambler has abnormal noise when it is running. After powering on the Bottle Unscrambler and confirming that there is no abnormal condition, stop the device, but the qualified infusion bottle upright in the bottle feeding bracket, and start the device again. The bottle will pass through the rotating carousel of the device and enter the conveyor belt to start the bottle unscramble operation. Run at low speed when starting up, and then adjust the lifting speed and unscramble speed according to the actual production, so that the speed of the Bottle Unscrambler equipment can match the actual production speed. To prevent such phenomena from happening. If such a phenomenon occurs, stop the machine immediately to eliminate the fault before it can continue to run. During the operation of the equipment, the bottles should be put in continuously, and observe whether there are phenomena such as pouring, jamming, broken bottles, etc. If any, stop the machine immediately and start the production after troubleshooting. After the production is over, stop the equipment, turn off the power of the Bottle Unscrambler, and clear the remaining materials out of the equipment.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. When the Liquid Filling Machine leaves the factory, it will provide customers with detailed Liquid Filling Machine operation procedures and operating specifications. If you are interested in Liquid Filling Machine, you can contact us, our website is www.cnzpack.com.

Liquid Filling Machine is specially designed for filling easy-to-open bottles. It has a reasonable design, simple structure, easy operation, and a mechanical bottle stop filling device. So what is the working principle of a Liquid Filling Machine? Let's take a look together next.

This is the content list:

l Transmission principle of Liquid Filling Machine

l The principle of the filling part of the Liquid Filling Machine

l Liquid Filling Machine's capping system

l The capping head of the Liquid Filling Machine

l The Liquid Filling Machine's tracking and filling mechanism

Transmission principle of Liquid Filling Machine

The Liquid Filling Machine transmits the power to the worm gear shaft of the reducer through the belt pulley, and then the worm gear shaft transmits the power to the paddlewheel shaft, the filling part, and the capping head through each gear. the filling part, the capping head, and each paddle wheel of the Liquid Filling Machine move synchronously, and the power is transmitted to the bottle feeding paddle wheel device through the bevel gear.

The principle of the filling part of the Liquid Filling Machine

The liquid bottle of the Liquid Filling Machine is sent to the transition pulley by the large bottle inlet paddlewheel and then sent to the synchronous belt by the transition pulley. The bottle is dragged forward at a uniform speed by the inserts on the synchronous belt, and the filling needle of the Liquid Filling Machine is inserted into the bottle mouth under the control of the tracking mechanism and runs forward synchronously with the bottle to achieve tracking and filling. The diving needle rises with the liquid level to play the role of defoaming.

Liquid Filling Machine's cap supply system

The cap supply system of the Liquid Filling Machine is composed of a cap delivery track, cap handling head, and cap-wearing mechanism. The lid management head adopts the principle of electromagnetic spiral oscillation to line up the messy lids and enter the lid delivery track through the reversing twist channel. When the Liquid Filling Machine passes through the lid-wearing mechanism, the bottle hangs on to the lid and passes through the pressure plate to make the lid wear correctly.

The capping head of the Liquid Filling Machine

After the liquid bottle of Liquid Filling Machine enters the cap rolling head turntable with the cap on, the three rolling knives which have been opened will turn forward with the Liquid Filling Machine turntable with the bottle as the center and press the cap under the control of the cam, then the three rolling knives will roll towards the cap at the same time under the action of the cone sleeve, and after rolling, they will leave the cap at the same time and return to the original position.

Liquid Filling Machine's tracking and filling mechanism

The Liquid Filling Machine drives the gear and rack to move, thus driving the filling needle to do the reciprocating movement. By adjusting the relative position of the Liquid Filling Machine's syringe holder and mounting frame, the filling needle can be accurately inserted into the middle of the bottle opening.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, and so far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and services as well as our integrity are widely praised at home and abroad. We will carry forward the spirit of "comprehensive innovation, perseverance", self-discipline and strive for the first, with enthusiasm and a new attitude to provide more perfect service for new and old customers. If you are interested in Liquid Filling Machine, please contact us, our website is www.cnzpack.com

Wenzhou Zungwan Intelligent Machine Co.,Ltd. is the professional equipment manufacturer to keep researching and developing the packing machinery for every type of liquid, powder, cream/ointment, fluid and half-fluid etc. materials. We have Obtained ISO9001 quality management system authentication and parts of our products have passed CE authentication. Our company has obtained more than 20 invention patents and utility model patents. The main products range from nail polish filling machine, perfume machine,perfume filling machine, powder serial automatically volume-measuring packing machine and inline capping machine, rotary capping machine and labeling machine, bottle unscrambler , screw capping machine ,tube filling and sealing machine, cartoning machine and other Packaging equipments.

So far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and our service as well as our integrity is acclaimed both in China and abroad. we will carry forward the spirit of "integrated innovation, and perseverance," discipline ourselves to be the first, and provide better and more perfect service for our new and old customers with enthusiasm and a new attitude.

Most Bag Packing Machines track and adjust various mechanical parameters through intelligent control instruments and menu-type software on the touch screen. The electronic display shows the length of the cut bag, the packaging speed, the net content of the filling, and the packaging output, etc., which can be understood at a glance. The standard color code tracking photoelectric system of the Bag Packing Machine can ensure the correct printing patterns of the packaged products. In addition, Bag Packing Machine can perform online status monitoring and fault diagnosis analysis of the working process. Once a problem occurs, Bag Packing Machine will automatically stop and display the cause and solution of the fault. So how do we maintain the Bag Packing Machine equipment in actual production? Let's take a look together next.

This is the content list:

l Maintenance after production

l Machine parts lubrication

l Care instructions

Maintenance after production

Every day after production, employees must clean the Bag Packing Machine before leaving get off work. First, the material barrels are cleaned in the warehouse, and the remaining materials on the tray are cleaned and kept clean. The remaining materials in other parts are cleaned up to prepare for the next use of the Bag Packing Machine.

Machine parts lubrication

The box part of the Bag Packing Machine is equipped with an oil gauge. The oil should be filled once before the Bag Packing Machine is turned on. It can be added in the middle according to the temperature rise and operating conditions of each bearing. The Bag Packing Machine worm gearbox must store oil for a long time. The oil level is high enough that the worm gear invades the oil. If it is used frequently, the oil must be replaced every three months. There is an oil plug at the bottom for draining oil. When refueling the Bag Packing Machine, do not let the oil spill out of the cup, let alone flow around the Bag Packing Machine and on the ground. Because oil is easy to pollute materials and affect product quality.

Care instructions

Check the parts of the Bag Packing Machine regularly, once a month, check whether the movable parts of the Bag Packing Machine worm gear, worm, lubricating block, bearings, and other moving parts are flexible and worn. If any defects are found, they should be repaired in time and should not be used reluctantly. The Bag Packing Machine should be used in a dry and clean room, and should not be used in places where the atmosphere contains acids and other gases that are corrosive to the body. When the Bag Packing Machine roller moves back and forth during work, please adjust the screws on the front bearing to the proper position. If the gear shaft of the Bag Packing Machine moves, please adjust the screws behind the bearing frame to the proper position, adjust the gap so that the bearing does not make a noise, turn the belt pulley by hand, and tighten properly. Too tight or too loose can make the Bag Packing Machine happen. The possibility of damage. If it is out of service for a long time, the Bag Packing Machine must be wiped and cleaned, and the smooth surface of the machine must be coated with anti-rust oil and covered with a cloth canopy.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that produces first-class Bag Packing Machine product quality and efficient and fast after-sales service, which has created excellent products of "Zhonghuan". Products are in great demand in the domestic and foreign markets. Keep improving, develop to satisfy customers, and meet market demands are our eternal topic and our sincere commitment to customers. If you are interested in Bag Packing Machine, you can contact us, our website is www.cnzpack.com.