In our production and life, the Liquid Filling Machine has a significant impact on many industries, so what is the method of using the Liquid Filling Machine? Let's go take a look next.
This is the content list:
l The ground wire must be well-grounded before the Liquid Filling Machine works
l Liquid Filling Machine liquid filling system assembly
The ground wire must be well-grounded before the Liquid Filling Machine works.
The ground wire must be well-grounded before the Liquid Filling Machine works, and then the appropriate standard syringe must be selected according to the different filling volumes. Generally, a 1ml syringe is used when the dispensing range is 0.2-1ml. Use a 5ml syringe for 1-5ml.use a 10ml syringe for 5-10ml. The 20ml model uses a 20ml glass infusion device. The 100ml model uses a 100ml glass infusion device, and the 500ml model uses the stainless steel filling system produced by our factory.
Liquid Filling Machine liquid filling system assembly
Pull out the inner core of the Liquid Filling Machine syringe, put the screw sleeve on the inner core of the syringe, and use the screw sleeve to properly fasten it to the lower base (cleanliness must be paid when disassembling the syringe). Place the upper clamp seat on the outlet end of the Liquid Filling Machine syringe jacket, and properly tighten the nuts on both sides to assemble the inner core and outer jacket of the installed Liquid Filling Machine syringe into one body. At this point, the Liquid Filling Machine injection system is assembled.
Place the Liquid Filling Machine valve with the arrow facing upwards and the arrow mark facing outwards and fix it on the fixing screw with a nut. Assemble the Liquid Filling Machine with a complete liquid filling system, align the upper and lower round holes of the liquid filling system components with the upper and lower fixing rods respectively, and put them on the bearing so that the outer end surface and the bearing surface are levels. When assembling the lower end, do not make the screw sleeve and the crank touch to prevent abnormal noise when the crank on the Liquid Filling Machine rotates (the screw sleeve and the crank are about 1mm apart when installed correctly). After the liquid filling system is installed correctly, tighten it. Tighten the screws up and down. Use a short hose to connect the Liquid Filling Machine syringe to the valve connection nozzle. The liquid inlet pipe is connected to the water inlet, and the liquid outlet pipe is connected to the water outlet. To prevent the liquid inlet and outlet pipes from being entangled, clip the liquid inlet and outlet pipes into the ear openings on the side of the casing.
Turn the crank of the Liquid Filling Machine by hand, it should be able to rotate freely, otherwise, the assembly is wrong, you should check whether the Liquid Filling Machine injection system is fastened to the rotating bearing.
Our company has obtained more than 20 invention patents and utility model patents. The main products are a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and online capping machine, capping machine and labeling machine, bottle unscrambler, tube filling and sealing machine, Cartoning machines, and other packaging equipment. If you are interested in Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.
Pharmaceutical Filler and Capper, whether semi-automatic or fully automatic, will encounter more or less in the process of using different places of failure, in the face of Pharmaceutical Filler and Capper's special parts of the failure, how do we find the problem as soon as possible and solve it? Let's take a look at it.
This is the content list:
l Pharmaceutical Filler and Capper's PLC failure
l Pharmaceutical Filler and Capper's Magnetic Switch Failure
l Pharmaceutical Filler and Capper solenoid valve failure
Pharmaceutical Filler and Capper PLC Failure
If the point controls Pharmaceutical Filler and Capper, the fault phenomenon is that the motor runs after the signal start Pharmaceutical Filler and Capper, but the motor does not stop running after the stop signal is issued. And Capper only stops running when the PLC is powered down. If the point controls the solenoid valve. The fault phenomenon is that the solenoid valve coil is not energized, and the cylinder is not reset. If the PLC of Pharmaceutical Filler and Capper is hit with external force to make the sticking point separate, it can assist to determine the fault of Pharmaceutical Filler and Capper.
Pharmaceutical Filler and Capper's magnetic switch failure
Pharmaceutical Filler and Capper's magnetic switch is used to detecting the position of the cylinder and control the cylinder travel. The four cylinders of laminating, pushing, pressing, and fusing knife are interrelated, and the magnetic switch is used to detect and control their positions. Pharmaceutical Filler and Capper failure is mainly manifested as the subsequent cylinders do not move, because the cylinder speed of Pharmaceutical Filler and Capper is faster, which causes the magnetic switch cannot detect the signal. Such as pushing the package cylinder speed is too fast, after pushing the package reset, the pressure package and fusion knife cylinder do not move.
Solenoid valve failure of Pharmaceutical Filler and Capper
Pharmaceutical Filler and Capper solenoid valve failure is mainly manifested as the cylinder does not move or does not reset, the reason is that Pharmaceutical Filler and Capper cylinder solenoid valve cannot change direction or tampering air. If the solenoid valve falters, the air pressure of Pharmaceutical Filler and Capper can't reach the working pressure because the inlet and outlet air paths are connected, and the knife beam doesn't rise to the place. the proximity switch of Pharmaceutical Filler and Capper knife beam protection doesn't work, and the precondition of full machine operation is not established. Pharmaceutical Filler and Capper does not operate, which is easily confused with an electrical fault. Solenoid valve air leakage sound, listen carefully to the source of sound and hand search for air leakage points, generally can easily identify the air leakage solenoid valve.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, with first-class product quality and efficient and fast after-sales service, forging the excellent products of "Central". Pharmaceutical Filler and Capper will undergo a lot of product testing before leaving the factory to reduce the probability of failure of Pharmaceutical Filler and Capper, and also provide customers with high-quality Pharmaceutical Filler and Capper warranty service. If you are interested in Pharmaceutical Filler and Capper, you can contact us, our website is www.cnzpack.com.
In our production and life, the Cartoning Machine is of great significance to us, but sometimes, the Cartoning Machine will fail, so what is the reason for the failure of the Cartoning Machine? Next, let us analyze it together.
This is the content list:
Stop or stop between conveyor belts
The carton cannot be sucked down
The carton is not formed or ejected at the mouth of the box feeding template after being sucked
Can't suck the instructions
The paper rebounds during the suction process of the manual
The manual does not fold well
Uneven folding of the manual
There are curls and creases after the manual is folded
Manual stuck in the fence
1. Cartoning Machine shuts down at intervals to check if there is a shortage of materials and automatically starts up when supplemented.
2. Shut down the Cartoning Machine to check whether the power supply including the power supply part, the motor, or the governor is normal.
1. Whether the cartons of Cartons Machine are arranged neatly.
2. Whether the cartons of the Cartoning Machine are pasted together.
3. Whether the air pressure of the Cartoning Machine suction head is normal.
1. Check if the cartons of Cartons Machine are too hard.
2. Check whether the position of the guide rod of the cartons placed by the Cartoning Machine and the box delivery template are not correct.
3. Check whether the small hook spring at the rear of the Cartoning Machine delivery template is deformed.
4. Check if the height of the suction head of the Cartoning Machine and the box delivery track is correct.
1. Whether the Cartoning Machine manual is deformed, causing the suction head to fail to suck.
2. Whether the suction head gas of the Cartoning Machine is parallel to the manual.
3. Whether the paper width of the Cartoning Machine manual is different, the error must be within 1mm. The stacking position of the manual should be adjusted to a difference of 0.5mm from the inner edge when the suction head rises to the high position.
4. The small paper-separating hook above the suction head of the Cartoning Machine origami moves too early. Generally, the small hook should be inserted into the gap between the paper and the paper before the suction head is about to drop. The height of the small hook is adjusted to be 0.5mm away from the suction head when it is in the high position.
1. The foot-lifting action of the Cartoning Machine's manual was too early, and the manual was taken away by the foot support before being pulled down. The position of the feet of the Cartoning Machine is so that it does not touch the sucked manual when it is returned and it returns to the high position when the paper picking notch wheel has not pulled the paper.
2. Whether the matching speed of the Cartoning Machine suction head and paper picking wheel is the same. The suction head of the Cartoning Machine should be lowered first, and then the front part of the paper picking notch wheel should be pressed onto the paper.
1. Check if the Cartoning Machine paper is deformed and bent, and if there are burrs.
2. Is there any foreign matter in the fence of the Cartoning Machine blocking the paper?
3. The gap between the opening of the Cartoning Machine fence and the folding stick is too large, causing the paper to come out.
4. Is the gap between Cartons Machine's folding sticks too large to hold the paper? Adjust the adjusting screws at both ends of the folding stick to reduce the gap. If the Cartoning Machine folding stick has been used for too long and worn out, the folding stick must be replaced.
Check the Cartoning Machine to adjust the front and rear positions of the barriers in the fence to achieve the required folding size.
1. Is the gap between the Cartoning Machine baffle and the folding stick too large? Adjust the middle position of the baffle and folding stick.
2. If the middle position of the Cartoning Machine baffle and the folding stick has been adjusted, and there is still a large gap, remove the positioning pins on the Cartoning Machine baffle and re-adjust until the gap does not feed paper.
1. Whether the paper feeding gap of Cartoning Machine folding stick is too large and paper feeding is weak. The adjustment method is the same as above.
2. The installation position of the lower half of the Cartoning Machine fence is too long than the arc guide plate on it so that the paper cannot enter the folding stick below. Loosen all the fixing screws on the Cartoning Machine fence and adjust the board backward, but it should not be shorter than the upper guide plate and should be 1-3 mm longer than the guide plate. If it is shorter than the guide plate, the Cartoning Machine manual may go directly into the folding stick below without folding.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It will conduct a large number of tests before the Cartoning Machine leaves the factory to reduce the failure of the Cartoning Machine and provide warranty services. If you are interested in the Cartoning Machine, you can contact us Contact, our website is www.cnzpack.com.
The tube Filling machine And the Sealing machine are determined by multiple parameters. It is impossible to describe a Tube Filling machine And Sealing machine with any single parameter. Shaft power, blade displacement, pressure head, blade diameter, and filling speed are the five basic parameters that describe a Tube Filling Machine And Sealing machine. So, let's take a look at the principle of the Tube Filling machine And Sealing machine together. Here are some answers.
Here is the content list:
l Basic parameters.
l The shear rate of the fluid.
l Small slot and big slot.
The displacement of the blade is proportional to the flow rate of the blade itself, the first power of the blade speed, and the third power of the blade diameter. The shaft power consumed by the filling is proportional to the specific gravity of the fluid, the power standard of the blade itself, the third power of the speed, and the fifth power of the blade diameter. In the case of a certain power and blade form, the blade displacement and pressure head can be adjusted by changing the diameter of the blade and the matching of the speed. That is, the large diameter blade is equipped with a low-speed Tube Filling machine And a Sealing machine. High flow effect and low-pressure head, while the small diameter blade with high speed produces a higher pressure head and lower flow effect.
The shear rate of the fluid.
In the filling tank, the only way to make the micelles collide with each other is to provide a sufficient shear rate. According to the mechanism of the Tube Filling Machine And Sealing machine, it is because of the existence of fluid velocity difference that the fluid layers are mixed. Therefore, where the filling process always involves the fluid shear rate lhhaha620. Shear stress is a force that is the real cause of bubble dispersion and droplet breaking in filling applications. It must be pointed out that the shear rate at each point of the fluid in the entire stirred tank is not the same.
Small slot and big slot.
Experimental research shows that, as far as the blade area is concerned, no matter what type of blade, when the diameter of the blade is constant, the maximum shear rate and the average shear rate increase with the increase of the speed. However, when the rotation speed is constant, the relationship between the maximum shear rate and the average shear rate, and the diameter of the blade is related to the slurry type. When the rotation speed is constant, the maximum shear rate of the radial blade increases with the increase of the blade diameter, and the average shear rate has nothing to do with the diameter of the blade. These concepts about the shear rate of the blade area require special care in the design of the Tube Filling Machine And Sealing machine to reduce and enlarge. Because the small groove is compared with the large groove, the small groove Tube Filling Machine and Sealing machine often has the characteristics of high speed, small blade diameter, and low tip speed. The large groove Tube Filling Machine And Sealing machine often has the characteristics of low speed, large blade diameter, and high tip speed.
Our official website is https:// www.cnzpack.com/. If you are engaged in work related to the Tube Filling machine And Sealing machine, you can communicate with us on the website.
With the increasingly fierce competition in the manufacturing and production of plastic bottles in the food and pharmaceutical industries, Bottle Unscrambler has become more and more solid backing for the food and pharmaceutical plastic bottle markets. So how does it play a role? We will introduce the work process and personnel operation specifications of Bottle Unscrambler. Let's take a look together next.
This is the content list:
The workflow of Bottle Unscrambler
Personnel operation specification of Bottle Unscrambler
The workflow of Bottle Unscrambler is generally as follows: manually put materials into the storage bottle library, the materials in the storage bottle library will be automatically quantified and fed to the turntable at the set speed. The turntable rotates at a high speed to supply the bottles as required, the web wheel The irregular bottles are removed, and the bottle dividing part sends the bottles from the turntable to the bottle unscramble part at a certain speed. The Bottle Unscrambler part of the Bottle Unscrambler clamps the bottles to the working surface of the conveyor through the conveyor belts on both sides, and at the same time sorts the bottles through the bottle turner. The Bottle Unscrambler electronic control system performs real-time monitoring and feedback through the sensors of each part to achieve fully automated operation requirements, and save a lot of labor costs and avoid losses caused by human error factors.
To ensure the normal and safe operation of Bottle Unscrambler, there are special operating procedures established for it. Operators and equipment management personnel shall perform standardized operations of Bottle Unscrambler under these procedures. This safe operation specification is commonly used in Bottle Unscramblers, mixers, high-speed automatic Bottle Unscramblers, etc.
1. First check the Bottle Unscrambler's intact, clean, and expiration status identification and the equipment operation record of the shift. If the inspection finds that the Bottle Unscrambler has exceeded the cleaning validity period, it is necessary to further clean the equipment according to the equipment cleaning operation rules and fill in the equipment status identification.
2. Check the Bottle Unscrambler and the Bottle Unscrambler to confirm that there is no foreign matter, and turn the bottle plate and unscrambler to confirm that it can work normally.
3. Turn on the Bottle Unscrambler power switch, check the touch screen and three photoelectric switches. If both are energized, the lack of a bottle alarm will be displayed on the touch screen. When the electric eye is blocked by hand, the screen displays the blocking alarm, and the two photoelectric switches are in a normal state.
4. Turn on the Bottle Unscrambler compressed air, use the bottom of the bottle to shake under the electric eye of the bottle puller, compressed air will be sprayed out, and the equipment can be turned on normally.
To ensure that the various parts of the Bottle Unscrambler can work normally, the formal operation can be divided into five steps: click the host start and lift start on the touch screen respectively, and observe whether the Bottle Unscrambler has abnormal noise when it is running. After powering on the Bottle Unscrambler and confirming that there is no abnormal condition, stop the device, but the qualified infusion bottle upright in the bottle feeding bracket, and start the device again. The bottle will pass through the rotating carousel of the device and enter the conveyor belt to start the bottle unscramble operation. Run at low speed when starting up, and then adjust the lifting speed and unscramble speed according to the actual production, so that the speed of the Bottle Unscrambler equipment can match the actual production speed. To prevent such phenomena from happening. If such a phenomenon occurs, stop the machine immediately to eliminate the fault before it can continue to run. During the operation of the equipment, the bottles should be put in continuously, and observe whether there are phenomena such as pouring, jamming, broken bottles, etc. If any, stop the machine immediately and start the production after troubleshooting. After the production is over, stop the equipment, turn off the power of the Bottle Unscrambler, and clear the remaining materials out of the equipment.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. When the Liquid Filling Machine leaves the factory, it will provide customers with detailed Liquid Filling Machine operation procedures and operating specifications. If you are interested in Liquid Filling Machine, you can contact us, our website is www.cnzpack.com.
Wenzhou Zungwan Intelligent Machine Co.,Ltd. is the professional equipment manufacturer to keep researching and developing the packing machinery for every type of liquid, powder, cream/ointment, fluid and half-fluid etc. materials. We have Obtained ISO9001 quality management system authentication and parts of our products have passed CE authentication. Our company has obtained more than 20 invention patents and utility model patents. The main products range from nail polish filling machine, perfume machine,perfume filling machine, powder serial automatically volume-measuring packing machine and inline capping machine, rotary capping machine and labeling machine, bottle unscrambler , screw capping machine ,tube filling and sealing machine, cartoning machine and other Packaging equipments.
So far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and our service as well as our integrity is acclaimed both in China and abroad. we will carry forward the spirit of "integrated innovation, and perseverance," discipline ourselves to be the first, and provide better and more perfect service for our new and old customers with enthusiasm and a new attitude.
Speaking of Bag packaging machines for large machinery, it is necessary to briefly talk about the knowledge of stand-up pouches. Bag packaging machines in the application, development, and growth of stand-up pouches played a role in what? Let's look at it together next.
This is the list of contents:
Stand-up pouches in brief
The basic classification of stand-up pouches
Stand-up pouches produced by Bag packaging machines are flexible packaging bags with a horizontal support structure at the bottom. It does not rely on any support, whether the bag is opened or not, it can stand on its own. Since its appearance and promotion, stand-up pouches have been very popular. With their good design and function, they have been widely used in food, daily necessities, pharmaceuticals, and other fields. Stand-up pouches produced by Bag packaging machines are mainly used for juice drinks, sports drinks, spices, and other products. In addition to the food industry, the application of some Bag packaging machine products such as detergents, daily cosmetics, pharmaceuticals, etc. is gradually increasing.
The basic classification of stand-up pouches
1. Ordinary stand-up pouches
That is, the general form of the Bag packaging machine produced by the stand-up pouches in the form of four seals, cannot be resealed and reopened. This stand-up pouch packaging machine to produce stand-up pouches is generally used in the industrial supplies industry.
2. Stand-up pouches with suction nozzles
Stand-up pouches with suction nozzles produced by the Bag packaging machine are more convenient to pour or suck out the contents and can be re-closed and re-opened at the same time. It can be thought of as a combination of stand-up pouches and ordinary bottle spout.
3. Stand-up pouches with zipper
Stand-up pouches with zippers produced by the Bag packaging machine can also be re-closed and re-opened. As the zipper produced by the Bag packaging machine is not closed, the seal strength is limited, so this form is not suitable for packaging liquids and volatile substances.
4. Special-shaped stand-up pouches
That is, according to the packaging needs, based on the traditional packaging bags, change the Bag packaging machine production of a variety of new shapes of stand-up pouches, such as waist design, bottom deformation design, handle design, etc.
Bag packaging machine production of stand-up pouches not only improves the product grade, but also strengthens the visual effect of the shelf, and is easy to carry, easy to use, with good preservation and sealing performance. The development of stand-up pouches produced by the Bag packaging machine, but also the packaging machinery industry to follow the trend, the development of adaptable Bag packaging machine.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops a wide range of packaging machinery for liquid, powder, cream/paste, fluid, and semi-fluid materials. We have obtained ISO9001 quality management system certification and some of our products have passed CE certification. Our company has obtained more than 20 invention patents and utility model patents. Our main products include a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and in-line capping machine, capping machine and labeling machine, bottle management machine, tube filling and sealing machine, cartooning machine, and other packaging equipment. If you are interested in a Bag packaging machine, you can contact us, our website is www.cnzpack.com.
Due to the particularity of the environment in which the Liquid Filling Machine equipment is used, the structure of the metal itself is prone to corrosion. The external environment such as temperature, humidity, and air will directly cause the metal to corrode. After the Liquid Filling Machine equipment is corroded, the color, appearance, and basic performance of the machine may change, which causes damage to the machine equipment and also causes a waste of energy, causing the company to suffer a greater loss. To reduce the damage of the Liquid Filling Machine caused by corrosion, we should do anti-corrosion work during design, production, and later use. So what are the anti-corrosion methods of Liquid Filling Machines? Let's take a look together next.
This is the content list:
Selection of Liquid Filling Machine materials
Liquid Filling Machine structure and process
Liquid Filling Machine corrosion inhibitor
Most of the Liquid Filling Machine equipment materials used in the manufacturing industry are carbon steel. The price of this kind of steel is relatively low, and at the same time, it is more convenient to purchase and easy to process. Such steel will not cause major corrosion when used in the ordinary working environment, and will not cause major harm to the use of Liquid Filling Machine equipment. But if it is used in an enterprise, its working environment may cause serious erosion.
If the collective shape design of the Liquid Filling Machine components is too complicated or unreasonable, it may cause defects such as thermal stress, dust accumulation, Liquid Filling Machine stress, and liquid accumulation, which may lead to corrosion in the connecting and unloading parts. From the perspective of anti-corrosion, comprehensive consideration is given to the design of the Liquid Filling Machine structure.
Liquid Filling Machine corrosion inhibitor is a chemical substance that is added to the corrosion inhibitor system at a proper concentration, which can significantly reduce the corrosion rate of the metal and has a small effect on the concentration of the corrosive agent. The amount of Liquid Filling Machine corrosion inhibitor is very small. Although it cannot change the corrosion tendency of the metal in the medium, it can form a protective film on the metal surface to slow down the corrosion rate of the metal, thereby reducing the corrosion of the metal.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. So far, we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and services as well as our integrity are widely praised at home and abroad. Before the Liquid Filling Machine leaves the factory, the corrosion resistance of the Liquid Filling Machine will be enhanced. If you are interested in the Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.