ZHY-339Y Automatic Liquid Packing Machine wholesale- China Manufacturers Factory Suppliers

In our production and life, the Liquid Filling Machine has a significant impact on many industries, so what is the method of using the Liquid Filling Machine? Let's go take a look next.

This is the content list:

l The ground wire must be well-grounded before the Liquid Filling Machine works

l Liquid Filling Machine liquid filling system assembly

The ground wire must be well-grounded before the Liquid Filling Machine works.

The ground wire must be well-grounded before the Liquid Filling Machine works, and then the appropriate standard syringe must be selected according to the different filling volumes. Generally, a 1ml syringe is used when the dispensing range is 0.2-1ml. Use a 5ml syringe for 1-5ml.use a 10ml syringe for 5-10ml. The 20ml model uses a 20ml glass infusion device. The 100ml model uses a 100ml glass infusion device, and the 500ml model uses the stainless steel filling system produced by our factory.

Liquid Filling Machine liquid filling system assembly　　

Pull out the inner core of the Liquid Filling Machine syringe, put the screw sleeve on the inner core of the syringe, and use the screw sleeve to properly fasten it to the lower base (cleanliness must be paid when disassembling the syringe). Place the upper clamp seat on the outlet end of the Liquid Filling Machine syringe jacket, and properly tighten the nuts on both sides to assemble the inner core and outer jacket of the installed Liquid Filling Machine syringe into one body. At this point, the Liquid Filling Machine injection system is assembled.

Place the Liquid Filling Machine valve with the arrow facing upwards and the arrow mark facing outwards and fix it on the fixing screw with a nut. Assemble the Liquid Filling Machine with a complete liquid filling system, align the upper and lower round holes of the liquid filling system components with the upper and lower fixing rods respectively, and put them on the bearing so that the outer end surface and the bearing surface are levels. When assembling the lower end, do not make the screw sleeve and the crank touch to prevent abnormal noise when the crank on the Liquid Filling Machine rotates (the screw sleeve and the crank are about 1mm apart when installed correctly). After the liquid filling system is installed correctly, tighten it. Tighten the screws up and down. Use a short hose to connect the Liquid Filling Machine syringe to the valve connection nozzle. The liquid inlet pipe is connected to the water inlet, and the liquid outlet pipe is connected to the water outlet. To prevent the liquid inlet and outlet pipes from being entangled, clip the liquid inlet and outlet pipes into the ear openings on the side of the casing.

Turn the crank of the Liquid Filling Machine by hand, it should be able to rotate freely, otherwise, the assembly is wrong, you should check whether the Liquid Filling Machine injection system is fastened to the rotating bearing.

Our company has obtained more than 20 invention patents and utility model patents. The main products are a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and online capping machine, capping machine and labeling machine, bottle unscrambler, tube filling and sealing machine, Cartoning machines, and other packaging equipment. If you are interested in Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.

They ordered two hand sanitizer filling lines, requiring a speed of 150 bottles per minute, from automatic bottle management - automatic filling - automatic cap management - automatic capping - automatic labeling.

The whole production line was designed, developed and produced by our company, and it took 70 days from the finalization of the contract to delivery. Because of the outbreak of New Crown epidemic in the U.S., we completed the delivery of the equipment ahead of schedule and flew it to the U.S.

In our production and life, Capping Machine is also called a Capping Machine, Capping Machine, or Capping Machine, which is used for screwing and unscrewing the caps of plastic bottles and glass bottles (molded bottles or tube bottles). equipment. Capping Machine is highly intelligent capping equipment with advanced technology, unique design, and easy operation. During the entire capping process, workers only need to place the cap on the mouth of the bottle, and then the bottle is automatically sent to the capping wheel and automatically tightened to complete the capping operation. The Capping Machine evacuates the packaging bottle and then tightens it, which prolongs the storage time of the packaging, reduces the failure rate of the Capping Machine, and improves the packaging efficiency of the Capping Machine. So what are the matters needing attention when operating Capping Machine correctly? Let's take a look together next.

This is the content list:

l Capping Machine rolling wheel adjustment

l Capping Machine lock wheel adjustment

l Capping Machine cap lock

l Capping Machine height adjustment

Capping Machine rolling wheel adjustment

Place the Capping Machine bottle on the bracket and raise the bracket to the highest point. First, loosen the lock nut to adjust the rolling wheel so that the (sprung) edge of the two Capping Machine rolling wheels is at the threading of the bottle. Click on it, then loosen the lock nut, and then adjust the adjusting screw so that the edges of the two rolling wheels are in contact with the cover, and a little pressure is appropriate, and then tighten the nut.

Capping Machine lock wheel adjustment

Adjust the two Capping Machine locking wheels, first loosen the locking nuts, adjust the locking wheels so that the edges of the two locking wheels are in contact with the lower edge of the bottle cap, a little pressure is appropriate, and then tighten the nuts (Note: Adjust Capping Machine Should be from loose to tight, adjust while pulling the lock).

Capping Machine cap lock

Loosen the top screw, remove the Capping Machine gland head, and then remove the entire Capping Machine lock head, install the appropriate plastic lock head on the cone sleeve, and then adjust the lifting height of the bracket to meet the working requirements.

Capping Machine height adjustment

Start the Capping Machine to lower the bracket to the lowest point, then place the bottle on the bracket, loosen the brake nut, turn the adjusting screw to raise the bracket, and then adjust the appropriate distance between the cap of the Capping Machine and the capping head (generally All are adjusted in place at the factory).

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. We have obtained ISO9001 quality management system certification, and some products have passed CE certification. Our company has obtained more than 20 invention patents and utility model patents. If you are interested in Capping Machine, you can contact us, our website is www.cnzpack.com.

The tube Filling machine And the Sealing machine are determined by multiple parameters. It is impossible to describe a Tube Filling machine And Sealing machine with any single parameter. Shaft power, blade displacement, pressure head, blade diameter, and filling speed are the five basic parameters that describe a Tube Filling Machine And Sealing machine. So, let's take a look at the principle of the Tube Filling machine And Sealing machine together. Here are some answers.

Here is the content list:

l Basic parameters.

l The shear rate of the fluid.

l Small slot and big slot.

Basic parameters.

The displacement of the blade is proportional to the flow rate of the blade itself, the first power of the blade speed, and the third power of the blade diameter. The shaft power consumed by the filling is proportional to the specific gravity of the fluid, the power standard of the blade itself, the third power of the speed, and the fifth power of the blade diameter. In the case of a certain power and blade form, the blade displacement and pressure head can be adjusted by changing the diameter of the blade and the matching of the speed. That is, the large diameter blade is equipped with a low-speed Tube Filling machine And a Sealing machine. High flow effect and low-pressure head, while the small diameter blade with high speed produces a higher pressure head and lower flow effect.

The shear rate of the fluid.

In the filling tank, the only way to make the micelles collide with each other is to provide a sufficient shear rate. According to the mechanism of the Tube Filling Machine And Sealing machine, it is because of the existence of fluid velocity difference that the fluid layers are mixed. Therefore, where the filling process always involves the fluid shear rate lhhaha620. Shear stress is a force that is the real cause of bubble dispersion and droplet breaking in filling applications. It must be pointed out that the shear rate at each point of the fluid in the entire stirred tank is not the same.

Small slot and big slot.

Experimental research shows that, as far as the blade area is concerned, no matter what type of blade, when the diameter of the blade is constant, the maximum shear rate and the average shear rate increase with the increase of the speed. However, when the rotation speed is constant, the relationship between the maximum shear rate and the average shear rate, and the diameter of the blade is related to the slurry type. When the rotation speed is constant, the maximum shear rate of the radial blade increases with the increase of the blade diameter, and the average shear rate has nothing to do with the diameter of the blade. These concepts about the shear rate of the blade area require special care in the design of the Tube Filling Machine And Sealing machine to reduce and enlarge. Because the small groove is compared with the large groove, the small groove Tube Filling Machine and Sealing machine often has the characteristics of high speed, small blade diameter, and low tip speed. The large groove Tube Filling Machine And Sealing machine often has the characteristics of low speed, large blade diameter, and high tip speed.

Our official website is https:// www.cnzpack.com/. If you are engaged in work related to the Tube Filling machine And Sealing machine, you can communicate with us on the website.

Wenzhou Zungwan Intelligent Machine Co.,Ltd. is the professional equipment manufacturer to keep researching and developing the packing machinery for every type of liquid, powder, cream/ointment, fluid and half-fluid etc. materials. We have Obtained ISO9001 quality management system authentication and parts of our products have passed CE authentication. Our company has obtained more than 20 invention patents and utility model patents. The main products range from nail polish filling machine, perfume machine,perfume filling machine, powder serial automatically volume-measuring packing machine and inline capping machine, rotary capping machine and labeling machine, bottle unscrambler , screw capping machine ,tube filling and sealing machine, cartoning machine and other Packaging equipments.

So far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and our service as well as our integrity is acclaimed both in China and abroad. we will carry forward the spirit of "integrated innovation, and perseverance," discipline ourselves to be the first, and provide better and more perfect service for our new and old customers with enthusiasm and a new attitude.

Liquid Filling Machine is specially designed for filling easy-to-open bottles. It has a reasonable design, simple structure, easy operation, and a mechanical bottle stop filling device. So what is the working principle of a Liquid Filling Machine? Let's take a look together next.

This is the content list:

l Transmission principle of Liquid Filling Machine

l The principle of the filling part of the Liquid Filling Machine

l Liquid Filling Machine's capping system

l The capping head of the Liquid Filling Machine

l The Liquid Filling Machine's tracking and filling mechanism

Transmission principle of Liquid Filling Machine

The Liquid Filling Machine transmits the power to the worm gear shaft of the reducer through the belt pulley, and then the worm gear shaft transmits the power to the paddlewheel shaft, the filling part, and the capping head through each gear. the filling part, the capping head, and each paddle wheel of the Liquid Filling Machine move synchronously, and the power is transmitted to the bottle feeding paddle wheel device through the bevel gear.

The principle of the filling part of the Liquid Filling Machine

The liquid bottle of the Liquid Filling Machine is sent to the transition pulley by the large bottle inlet paddlewheel and then sent to the synchronous belt by the transition pulley. The bottle is dragged forward at a uniform speed by the inserts on the synchronous belt, and the filling needle of the Liquid Filling Machine is inserted into the bottle mouth under the control of the tracking mechanism and runs forward synchronously with the bottle to achieve tracking and filling. The diving needle rises with the liquid level to play the role of defoaming.

Liquid Filling Machine's cap supply system

The cap supply system of the Liquid Filling Machine is composed of a cap delivery track, cap handling head, and cap-wearing mechanism. The lid management head adopts the principle of electromagnetic spiral oscillation to line up the messy lids and enter the lid delivery track through the reversing twist channel. When the Liquid Filling Machine passes through the lid-wearing mechanism, the bottle hangs on to the lid and passes through the pressure plate to make the lid wear correctly.

The capping head of the Liquid Filling Machine

After the liquid bottle of Liquid Filling Machine enters the cap rolling head turntable with the cap on, the three rolling knives which have been opened will turn forward with the Liquid Filling Machine turntable with the bottle as the center and press the cap under the control of the cam, then the three rolling knives will roll towards the cap at the same time under the action of the cone sleeve, and after rolling, they will leave the cap at the same time and return to the original position.

Liquid Filling Machine's tracking and filling mechanism

The Liquid Filling Machine drives the gear and rack to move, thus driving the filling needle to do the reciprocating movement. By adjusting the relative position of the Liquid Filling Machine's syringe holder and mounting frame, the filling needle can be accurately inserted into the middle of the bottle opening.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, and so far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and services as well as our integrity are widely praised at home and abroad. We will carry forward the spirit of "comprehensive innovation, perseverance", self-discipline and strive for the first, with enthusiasm and a new attitude to provide more perfect service for new and old customers. If you are interested in Liquid Filling Machine, please contact us, our website is www.cnzpack.com

Wenzhou Zungwan Intelligent Machine Co.,Ltd. is the professional equipment manufacturer to keep researching and developing the packing machinery for every type of liquid, powder, cream/ointment, fluid and half-fluid etc. materials. We have Obtained ISO9001 quality management system authentication and parts of our products have passed CE authentication. Our company has obtained more than 20 invention patents and utility model patents. The main products range from nail polish filling machine, perfume machine,perfume filling machine, powder serial automatically volume-measuring packing machine and inline capping machine, rotary capping machine and labeling machine, bottle unscrambler , screw capping machine ,tube filling and sealing machine, cartoning machine and other Packaging equipments.

So far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and our service as well as our integrity is acclaimed both in China and abroad. we will carry forward the spirit of "integrated innovation, and perseverance," discipline ourselves to be the first, and provide better and more perfect service for our new and old customers with enthusiasm and a new attitude.

The Mid-Autumn Festival is the second most important festival for a family reunion in China after the Spring Festival. Besides China, the Mid-Autumn Festival is also celebrated in many other Asian countries like Vietnam, Singapore, and Japan.

The Mid-Autumn Festival is also called the Moon Festival or Mooncake Festival. It would be celebrated on 21 September 2021. Gathering with families, eating moon cakes, and appreciating the fullest moon with lanterns, the Mid-Autumn Festival is a grand time for family reunions.

Besides those traditions in China, other Asian countries have their own unique customs of the Mid-Autumn Festival.

For example, the Mid-Autumn Festival is named Tết Trung Thu in Vietnamese. It is also known as a Children Festival. During the festival, parents will accompany their children and give them gifts like masks or lanterns. Most gifts are made by hand rather than buying at shops. Children would light lanterns and join in lion dance at the Mid-Autumn Festival.

Read Mid-Autumn Festival around the World to find more traditions in other countries.