ZHTB60 Tube Labeling Machine factory- China Factory Suppliers Manufacturers

With the continuous development of our production life, the emergence of Pharmaceutical Filler and Capper has brought great convenience to the industry. So what are the procedures and precautions for Pharmaceutical Filler and Capper? Let's take a look at it.

This is the content list:

l The operation method of Pharmaceutical Filler and Capper

l Safety rules for the use of Pharmaceutical Filler and Capper

l Precautions for Pharmaceutical Filler and Capper

The operation method of Pharmaceutical Filler and Capper

Pharmaceutical Filler and Capper installation precautions before use check, after the machine is installed, turn on the power, test runs the three-phase motor to ensure that the correct direction of operation, ensure that the pressure and flow of compressed air, check whether the motor, bearings, etc. need to be lubricated, no oil-free operation is strictly prohibited, normal before starting Pharmaceutical Filler and Capper. Filler And Capper at the same time, observe whether the fasteners of each part are loose, and only after the operation of each part is stable, can it be used normally. Check whether the function of the safety facilities of Pharmaceutical Filler and Capper is normal, check carefully whether there is water in all water tanks, whether the chainplate is stuck, whether there is debris on the conveyor belt, whether there are caps in the storage box, whether the water, power, and gas sources are connected before starting the machine. After all, conditions are ready, then close the main power QF, power indicator light, fault indicator, emergency stop indicator light is not on, then the start conditions are available, press the start button on the control box and the start switch at the filling, after the buzzer three warning, the whole machine starts running, take external washing, rinsing, filling fully automatic work mode, stop can be at the filling and control box press the stop button after the stop should turn off the main power.

Pharmaceutical Filler and Capper safety rules of use

1. No foreign objects (such as tools, rags, etc.) in Pharmaceutical Filler and Capper equipment.

2. Pharmaceutical Filler and Capper should not be allowed to have abnormal noise, if there is, it should be stopped immediately to check the reason.

3. All protective materials should be safe and reliable, it is strictly prohibited to wear clothing that may be hung by moving parts (such as scarves, bracelets, watches, etc.).

4. Long hair, should wear a hair cover.

5. Do not use water and other liquids to clean the electrical unit.

6. Cleaning should wear work clothes, gloves, glasses, etc., to prevent strong acid, strong alkali corrosion.

7. When Pharmaceutical Filler and Capper is running, someone must monitor it and do not approach the machine with tools or other objects.

8. Don't let the staff who are not related to the operation approach the installation of Pharmaceutical Filler and Capper.

Precautions for Pharmaceutical Filler and Capper

1、After unpacking Pharmaceutical Filler and Capper, first check whether the random technical information is complete and whether the machine is damaged in transportation, to solve the problem in time.

2、Install and adjust the feeding and discharging components according to the shape illustration in this manual.

3、Lubricate each lubrication point with new lubricant.

4、Turn the Pharmaceutical Filler and Capper by shaking the handle, check whether the Pharmaceutical Filler and Capper are running in the correct direction (facing the motor spindle in the counterclockwise direction), and the installation precautions of the Pharmaceutical Filler and Capper must be protected from grounding.

If you are interested in Pharmaceutical Filler and Capper, please contact us, our website is www.cnzpack.com.

The Cosmetic Filling machine And Capping machine has a wide range of applications, not only in the cosmetics industry but also in food, daily chemical, pharmaceutical, and other industries. It is very flexible to use, can be adapted to different bottle mouths, and the operation is relatively simple and quick. Because of its unique advantages, it has won unanimous praise from customers. Next, let's take a look at the advantages, characteristics, and manufacturer introduction of Cosmetic Filling machines And Capping Machines. Here are some answers.

Here is the content list:

l Advantages of Cosmetic Filling machine And Capping machine.

l The performance characteristics of Cosmetic Filling machine And Capping machine.

l Introduction of Cosmetic Filling machine And Capping machine manufacturer.

Advantages of Cosmetic Filling machine And Capping machine.

Cosmetic Filling Machine And Capping machine integrates mechanical, pneumatic, and automatic. The characteristics of a high degree of automation, high output, wide application, and good stability make this machine more popular. The Cosmetic Filling machine And Capping machine can automatically unscramble bottles, fill, seal, cap, and label. Equipped with an automatic internal plug-in row and external cover plug test, it can realize no internal plug and non-external plug and eliminate the non-external plug. The labeling adopts a belt rolling structure, a fast-rolling structure, and an 8-dimensional angle adjustment label to realize the labeling of two symmetrical labels or high-precision labeling.

The performance characteristics of Cosmetic Filling machine And Capping machine.

First, the man-machine interface setting, intuitive and convenient operation, PLC control, accurate loading. Frequency conversion control, arbitrary adjustment of production speed, automatic counting. Second, the Cosmetic Filling machine And Capping machine is made of stainless steel, which meets GMP requirements. Third, the equipment fully complies with GMP requirements. Microcomputer setting, accurate filling volume, convenient operation, automatic shutdown function, automatic shutdown for any track with continuous no filling and no internal clogging. Fourth, the Cosmetic Filling machine And Capping machine is easy to operate and easy to maintain.

Introduction of Cosmetic Filling machine And Capping machine manufacturer.

Wenzhou Zungwan Intelligent Machine Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream, ointment, fluid, and semi-fluid materials. We have obtained ISO9001 quality management system certification, and some products have passed CE certification. Our company has obtained more than 20 invention patents and utility model patents. The quality of our Cosmetic Filling Machine And Capping machine and service as well as our integrity are widely praised at home and abroad.

The first-class quality of Cosmetic Filling machine And Capping machine and efficient and fast after-sales service have created the excellent products of "Zhonghuan". Cosmetic Filling Machine And Capping machine is in great demand in domestic and foreign markets. Keep improving, develop to satisfy customers, and satisfy market demands are our eternal topic and our sincere commitment to customers.

Our official website is https:// www.cnzpack.com/. If you are engaged in work related to Cosmetic Filling machines And Capping machines or want to learn more about our company, you can communicate with us on the website. We wholeheartedly provide users with better products and services!

Speaking of Bag packaging machines for large machinery, it is necessary to briefly talk about the knowledge of stand-up pouches. Bag packaging machines in the application, development, and growth of stand-up pouches played a role in what? Let's look at it together next.

This is the list of contents:

• Stand-up pouches in brief

• The basic classification of stand-up pouches

Stand-up pouches in brief

Stand-up pouches produced by Bag packaging machines are flexible packaging bags with a horizontal support structure at the bottom. It does not rely on any support, whether the bag is opened or not, it can stand on its own. Since its appearance and promotion, stand-up pouches have been very popular. With their good design and function, they have been widely used in food, daily necessities, pharmaceuticals, and other fields. Stand-up pouches produced by Bag packaging machines are mainly used for juice drinks, sports drinks, spices, and other products. In addition to the food industry, the application of some Bag packaging machine products such as detergents, daily cosmetics, pharmaceuticals, etc. is gradually increasing.

The basic classification of stand-up pouches

1. Ordinary stand-up pouches

That is, the general form of the Bag packaging machine produced by the stand-up pouches in the form of four seals, cannot be resealed and reopened. This stand-up pouch packaging machine to produce stand-up pouches is generally used in the industrial supplies industry.

2. Stand-up pouches with suction nozzles

Stand-up pouches with suction nozzles produced by the Bag packaging machine are more convenient to pour or suck out the contents and can be re-closed and re-opened at the same time. It can be thought of as a combination of stand-up pouches and ordinary bottle spout.

3. Stand-up pouches with zipper

Stand-up pouches with zippers produced by the Bag packaging machine can also be re-closed and re-opened. As the zipper produced by the Bag packaging machine is not closed, the seal strength is limited, so this form is not suitable for packaging liquids and volatile substances.

4. Special-shaped stand-up pouches

That is, according to the packaging needs, based on the traditional packaging bags, change the Bag packaging machine production of a variety of new shapes of stand-up pouches, such as waist design, bottom deformation design, handle design, etc.

Bag packaging machine production of stand-up pouches not only improves the product grade, but also strengthens the visual effect of the shelf, and is easy to carry, easy to use, with good preservation and sealing performance. The development of stand-up pouches produced by the Bag packaging machine, but also the packaging machinery industry to follow the trend, the development of adaptable Bag packaging machine.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops a wide range of packaging machinery for liquid, powder, cream/paste, fluid, and semi-fluid materials. We have obtained ISO9001 quality management system certification and some of our products have passed CE certification. Our company has obtained more than 20 invention patents and utility model patents. Our main products include a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and in-line capping machine, capping machine and labeling machine, bottle management machine, tube filling and sealing machine, cartooning machine, and other packaging equipment. If you are interested in a Bag packaging machine, you can contact us, our website is www.cnzpack.com.

They ordered two hand sanitizer filling lines, requiring a speed of 150 bottles per minute, from automatic bottle management - automatic filling - automatic cap management - automatic capping - automatic labeling.

The whole production line was designed, developed and produced by our company, and it took 70 days from the finalization of the contract to delivery. Because of the outbreak of New Crown epidemic in the U.S., we completed the delivery of the equipment ahead of schedule and flew it to the U.S.

In our daily life, Capping Machine plays a vital role for us, so what are the main work processes and precautions of the Capping Machine? Let's take a look together next.

This is the content list:

• The main workflow of Capping Machine

• How to carry out daily maintenance and maintenance of Capping Machine

• How to deal with common problems of Capping Machine　

The main workflow of Capping Machine

We know that after the plastic bottles are sorted by the Capping Machine, they enter the conveyor chain in a single row. In the filling station, the plunger pump injects the liquid in the container into the plastic bottle. After filling, the plastic bottle enters the index plate and stops accurately at the capping station. Manually place the cap of the Capping Machine at the entrance of the friction beltline, take out the capping claw, screw the cap claw, and squeeze the tube claw to complete the capping action. Then the plastic bottle exits the index plate and enters the conveyor chain, and enters the labeling station to complete the round bottle labeling.

How to carry out daily maintenance and maintenance of Capping Machine

1. Always keep the Capping Machine clean, especially for the electrical appliances on the switchboard, to prevent moisture and dust, and it is forbidden to change the program of the inverter and the program controller at will.　

2. The power supply voltage of the Capping Machine should be stable, not exceeding ±15%, the material temperature should be kept at 10℃-40℃, the ambient temperature should be kept at 5℃～40℃, and the temperature should be kept at 5～95%PH.　

3. The flowmeter used by the Capping Machine for spray filling is a precision instrument. Therefore, the oil must be precision filtered before it can be filled.　　

4. Turn off the power supply and oil inlet valve of the Capping Machine after finishing the work.　　

5. Pay attention to the cleanliness of the infrared sensor from the Capping Machine. Frequently wipe it clean with clean cotton. It is strictly forbidden for any object to approach the sensor during the working process, and strong light should not be directly or reflected on the sensor, otherwise, it will prosper and malfunction.

6. Add cylinder lubricating oil to the pneumatic triplet regularly.　　

7. When the machine is not used for a long time, all parts should be wiped clean and covered with plastic or tarpaulin to prevent dust.

How to deal with common problems of Capping Machine

First, what should I do if the cylinder piston of the Capping Machine does not work? Confirm whether the safety emergency stop switch is safe. Confirm that the air supply switch of the Capping Machine is turned on. Check if the Capping Machine one-way signal valve is damaged.

Second, what should I do if the Capping Machine cylinder piston does not return after being pushed to the top? Confirm whether the moving target is in contact with the one-way valve.

Third, how to adjust the filling volume of the Capping Machine is inaccurate or not discharged?

Check whether the upper and lower throttle valves of the Capping Machine are closed, and increase the pumping speed of the throttle valve of the cylinder. Make sure that the Capping Machine quick-install tee is locked with a clamp. Confirm whether there are enough materials in the Capping Machine storage box. Make sure that the joints of the pipes of the Capping Machine are sealed.

Fourth, what should I do if the material of the Capping Machine flows out from the rear end of the cylinder? Check whether the sealing ring on the Capping Machine piston is worn. If it is worn, replace it and make sure that the piston and the piston rod are tight.

In addition to timely handling of problems, it is also necessary to do a good job of preventive work in advance. Doing a good job in daily maintenance can also reduce the failure rate of the Capping Machine. The daily maintenance and maintenance of the Capping Machine cannot be underestimated. This is a very important step. Daily maintenance on time can effectively extend the service life of the Capping Machine, improve the production efficiency of the enterprise, and keep Capping Machine in normal operation throughout the day, reducing manpower. The loss of material resources.

Wenzhou Zungwan Intelligent Machinery Co., Ltd.'s first-class product quality and efficient and quick after-sales service have created excellent products of "Zhonghuan". Products are in great demand in the domestic and foreign markets. Keep improving, develop to satisfy customers, and meet market demands are our eternal topic and our sincere commitment to customers. Therefore, Capping Machine is very popular among consumers. If you are interested in Capping Machine, you can contact us. Our website is www.cnzpack.com.

Tube filling machine and sealing machine is advanced equipment for sealing plastic pipes and aluminum-plastic pipes. It uses the thermal shock effect of the plastic tube produced by the ultrasonic sealing transducer and quickly melts the adhesive. The tube Filling machine And the Sealing machine does not need to add any additives, even if the surface is contaminated, it will not affect the sealing effect. Next, let's take a look at the advantages and applications of the Tube Filling machine And Sealing machine. Here are some answers.

Here is the content list:

• Advantages of Tube Filling machine And Sealing machine.

• Application field of Tube Filling machine And Sealing machine.

Advantages of Tube Filling machine And Sealing machine.

First, the servo motor controls the filling, and 8 nozzles are filled at the same time. Second, the Tube Filling Machine And the Sealing machine can achieve fast cleaning, fast adjustment, and step-less adjustment of the volume cylinder speed. The tube Filling machine And the Sealing machine is suitable for filling different specifications and different liquids. Third, the filling volume only needs to be adjusted once, each volume cylinder is fine-tuned, the filling accuracy is high and the consistency is good. The contact material part is 316L stainless steel and silicon rubber, which meets the GMP standard. Fourth, the filling piston-cylinder adopts imported geared motor step-less speed regulation, which is suitable for aqueous liquids and viscous liquids. Fifth, imported electromagnetic clutches and brakes eliminate inertia and high filling accuracy. Sixth, the man-machine interface communicates with the PLC. You can debug the device and change the type with simple settings on the screen. Seventh, bottling, positioning, filling, and discharging are all automatic. If the bottle is not in the correct position, the bottle is blocked, or the filling tube is not inserted into the bottle during filling, the equipment will automatically protect and continue to operate after troubleshooting.

Application field of Tube Filling machine And Sealing machine.

Tube filling machine and sealing machine is mainly used to fill ointment or viscous fluid materials into aluminum tubes, plastic tubes, or composite tubes. Then seal the end of the tube. The Tube Filling machine And Sealing machine adopts a new type of stainless steel butterfly valve dosing pump and a screw fine adjustment device. In addition, the Tube Filling Machine And Sealing machine is widely used for filling, sealing, and batch number printing of aluminum tube packaging products in cosmetics, toothpaste, ointment, food, shoe polish, adhesives, etc. Tube Filling machines And Sealing machines can also be widely used in product packaging in medicine, daily chemical, food, chemical, and other industries. Such as ointment, adhesive, silica gel, AB glue, skin cream, hair dye, shoe polish, toothpaste, and other liquid or paste-like materials filling and sealing.

Our official website is https:// www.cnzpack.com/. If you are engaged in work related to Tube Filling machine And Sealing machine or want to know more about our company, you can communicate with us on the website. Our company adheres to the corporate culture of "quality-oriented, customer first", and has always made unremitting efforts to become a professional Tube Filling machine And Sealing machine supplier in the industry.

In our production and life, the Liquid Filling Machine has a significant impact on many industries, so what is the method of using the Liquid Filling Machine? Let's go take a look next.

This is the content list:

l The ground wire must be well-grounded before the Liquid Filling Machine works

l Liquid Filling Machine liquid filling system assembly

The ground wire must be well-grounded before the Liquid Filling Machine works.

The ground wire must be well-grounded before the Liquid Filling Machine works, and then the appropriate standard syringe must be selected according to the different filling volumes. Generally, a 1ml syringe is used when the dispensing range is 0.2-1ml. Use a 5ml syringe for 1-5ml.use a 10ml syringe for 5-10ml. The 20ml model uses a 20ml glass infusion device. The 100ml model uses a 100ml glass infusion device, and the 500ml model uses the stainless steel filling system produced by our factory.

Liquid Filling Machine liquid filling system assembly　　

Pull out the inner core of the Liquid Filling Machine syringe, put the screw sleeve on the inner core of the syringe, and use the screw sleeve to properly fasten it to the lower base (cleanliness must be paid when disassembling the syringe). Place the upper clamp seat on the outlet end of the Liquid Filling Machine syringe jacket, and properly tighten the nuts on both sides to assemble the inner core and outer jacket of the installed Liquid Filling Machine syringe into one body. At this point, the Liquid Filling Machine injection system is assembled.

Place the Liquid Filling Machine valve with the arrow facing upwards and the arrow mark facing outwards and fix it on the fixing screw with a nut. Assemble the Liquid Filling Machine with a complete liquid filling system, align the upper and lower round holes of the liquid filling system components with the upper and lower fixing rods respectively, and put them on the bearing so that the outer end surface and the bearing surface are levels. When assembling the lower end, do not make the screw sleeve and the crank touch to prevent abnormal noise when the crank on the Liquid Filling Machine rotates (the screw sleeve and the crank are about 1mm apart when installed correctly). After the liquid filling system is installed correctly, tighten it. Tighten the screws up and down. Use a short hose to connect the Liquid Filling Machine syringe to the valve connection nozzle. The liquid inlet pipe is connected to the water inlet, and the liquid outlet pipe is connected to the water outlet. To prevent the liquid inlet and outlet pipes from being entangled, clip the liquid inlet and outlet pipes into the ear openings on the side of the casing.

Turn the crank of the Liquid Filling Machine by hand, it should be able to rotate freely, otherwise, the assembly is wrong, you should check whether the Liquid Filling Machine injection system is fastened to the rotating bearing.

Our company has obtained more than 20 invention patents and utility model patents. The main products are a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and online capping machine, capping machine and labeling machine, bottle unscrambler, tube filling and sealing machine, Cartoning machines, and other packaging equipment. If you are interested in Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.

The Cosmetic Filling machine And Capping machine integrates the functions of air purification, filling, inserting, capping, and venting. It is suitable for filling water injection, lotion, and cream products. The Cosmetic Filling machine And Capping machine has the advantages of reasonable design, stable performance, accurate quantity, glass tabletop, automatic bottle feeding, smooth operation and no noise, electric speed regulation of filling speed and filling volume, and convenient maintenance and cleaning. Next, let's take a look at the description and structural characteristics of the Cosmetic Filling machine And capping Machine. Here are some answers.

Here is the content list:

Description of Cosmetic Filling machine And Capping machine.

Structural characteristics of Cosmetic Filling machine And Capping machine.

Description of Cosmetic Filling machine And Capping machine.

The Cosmetic Filling machine And Capping machine adopts automatic low-vacuum filling, automatic bottle detection (no bottle no filling), three fillings, automatic lowering of the nozzle cap, circulation of the perfume bottle die, and wide adaptability. It can meet the volume of containers of different sizes and filling requirements. Cosmetic Filling Machine And Capping machine is equipped with air bottle cleaning, quantitative filling, negative pressure filling, pumping, roll cap, jacket, screw cap, rejection, labeling, and finished product collection. The mold moves in a circular motion, which makes it easy to change the bottle. The stepper motor is used for quantitative filling, and the filling volume can be adjusted quickly. The negative pressure device is used to fill the same liquid level and the manipulator releases the pump to increase the pump roll rate; the elastic rolling head is to avoid damage to the bottle body.

Structural characteristics of Cosmetic Filling machine And Capping machine.

The design of the Cosmetic Filling machine And Capping machine is very reasonable. The Cosmetic Filling machine And Capping machine has a reasonable and compact structure, stable operation, flexible operation, and convenient specification conversion and adjustment. The speed of the aluminum cover is adjustable. Using the principle of seven-station three-knife cap rolling, the aluminum cap is rolled without damage, and the rolling mouth is firm, smooth and flat. The operation of the machine is very simple. The internal pneumatic part adopts new pneumatic components. The piston and cylinder of cylinder are made of PTFE and stainless steel, which meets the requirements of GMP testing. The filling speed can be adjusted at will with high precision. The Cosmetic Filling machine And Capping machine can be modified according to actual production needs and can be transformed into a multi-head type, explosion-proof type, and overflow type system.

Wenzhou Zungwan Intelligent Machine Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream, ointment, fluid, and semi-fluid materials. Our official website is https:// www. cnzpack.com/. If you are engaged in work related to Cosmetic Filling machines And Capping machines or want to learn more about our company, you can communicate with us on the website. Our company adheres to the service tenet of "customer first", and implements the service of honesty and customer first.

Piston Filling Machine, Capacity: 25 Bpm ? 95,000 Heli Engineers Contact Supplier Stainless Steel Automatic Piston Filling Machine, For Food Industries, Capacity: 50 To 80 Bpm ? 6 Lakh Filsilpek Solutions Private Limited Contact Supplier Automatic Piston Filling Machine, 1.8 Kw, Capacity: 1600 To 2400 Bph ? 2.80 Lakh

Piston Filler Capable of dispensing everything from water to cottage cheese, and adhesives to soap, with an incredible accuracy. FEMC fillers maintain this level of accuracy with virtually no product distortion, even on products as delicate as …

Get top quality Lotion Filling Machine from leading Lotion Filling Machine Manufacturers

21/4/2018· Hey guys, check out my personal website, maybe you'll find out what you need.www.ytkpackingAlso I'm focusing on developing now, you can contact chinayaso...

Automatic spindle cappers are capable of speeds of up to 200 cpm. Our automatic spindle screw capping machines are by far the most popular machines for capping most products that take a screw cap. Changeovers are easy with a wide range of bottle and cap sizes. There are also several variations of cap sorters available for flat caps, barrel caps ...

Suppliers > "lip balm tube filling machine": 331 Supplier(s) Gold Supplier Assessed Supplier

Semi-Automatic Ultrasonic Tubes Filling Sealing Machine PVC Tube Filling Machine ZH-006 Ultrasonic sealing machine is advanced equipment for plastic tube sealing and aluminum plastic tube sealing. It uses ultrasonic seal the plastic tube heat shock effect produced by the transducer and to rapidly melt adhesive.

Saudi Arabia Tea bag Packaging Machine Manufacturer Release Date：2022-11-25 16:12:33 Views Frequency： 5 C18 Automatic Multi-function Tea Bag Packing Machine (Optional with Outer Envelope, Thread and Tag)