fruit juice Packing Machine- Suppliers Manufacturers Factory From China

Tube filling machine and sealing machine is advanced equipment for sealing plastic pipes and aluminum-plastic pipes. It uses the thermal shock effect of the plastic tube produced by the ultrasonic sealing transducer and quickly melts the adhesive. The tube Filling machine And the Sealing machine does not need to add any additives, even if the surface is contaminated, it will not affect the sealing effect. Next, let's take a look at the advantages and applications of the Tube Filling machine And Sealing machine. Here are some answers.

Here is the content list:

• Advantages of Tube Filling machine And Sealing machine.

• Application field of Tube Filling machine And Sealing machine.

Advantages of Tube Filling machine And Sealing machine.

First, the servo motor controls the filling, and 8 nozzles are filled at the same time. Second, the Tube Filling Machine And the Sealing machine can achieve fast cleaning, fast adjustment, and step-less adjustment of the volume cylinder speed. The tube Filling machine And the Sealing machine is suitable for filling different specifications and different liquids. Third, the filling volume only needs to be adjusted once, each volume cylinder is fine-tuned, the filling accuracy is high and the consistency is good. The contact material part is 316L stainless steel and silicon rubber, which meets the GMP standard. Fourth, the filling piston-cylinder adopts imported geared motor step-less speed regulation, which is suitable for aqueous liquids and viscous liquids. Fifth, imported electromagnetic clutches and brakes eliminate inertia and high filling accuracy. Sixth, the man-machine interface communicates with the PLC. You can debug the device and change the type with simple settings on the screen. Seventh, bottling, positioning, filling, and discharging are all automatic. If the bottle is not in the correct position, the bottle is blocked, or the filling tube is not inserted into the bottle during filling, the equipment will automatically protect and continue to operate after troubleshooting.

Application field of Tube Filling machine And Sealing machine.

Tube filling machine and sealing machine is mainly used to fill ointment or viscous fluid materials into aluminum tubes, plastic tubes, or composite tubes. Then seal the end of the tube. The Tube Filling machine And Sealing machine adopts a new type of stainless steel butterfly valve dosing pump and a screw fine adjustment device. In addition, the Tube Filling Machine And Sealing machine is widely used for filling, sealing, and batch number printing of aluminum tube packaging products in cosmetics, toothpaste, ointment, food, shoe polish, adhesives, etc. Tube Filling machines And Sealing machines can also be widely used in product packaging in medicine, daily chemical, food, chemical, and other industries. Such as ointment, adhesive, silica gel, AB glue, skin cream, hair dye, shoe polish, toothpaste, and other liquid or paste-like materials filling and sealing.

Our official website is https:// www.cnzpack.com/. If you are engaged in work related to Tube Filling machine And Sealing machine or want to know more about our company, you can communicate with us on the website. Our company adheres to the corporate culture of "quality-oriented, customer first", and has always made unremitting efforts to become a professional Tube Filling machine And Sealing machine supplier in the industry.

After the Labeling machine sensor sends a signal that the labeling object is ready to be labeled, the drive wheel on the Labeling machine turns up. As the rolled label is in a tight state on the equipment, when the Labeling machine backing paper is tightly attached to the peeling plate and changes direction, the Labeling machine label is forced to disengage due to the rigidity of its material and is ready to be labeled. At this time, the labeling object is located just below the label, under the action of the labeling wheel, to achieve synchronous labeling. After the Labeling machine has finished labeling, the sensor under the roll label sends a stop signal, the drive wheel comes to a standstill, and a labeling cycle end. No matter which type of Labeling machine, the labeling process is roughly the same. The difference is that the installation position of the Labeling machine is different, the labeling object is conveyed differently and positioned differently, and the form of the labeling roller of the Labeling machine is also different. So, what are the Labeling machine's requirements for labels? Let's look at it together next.

This is the content list:

l Surface material

l Release force

l At the end of the paper

l Processing quality

Surface material

Labeling machine label stiffness is the key to labeling, so the Labeling machine surface material is required to have a certain strength and hardness. Labeling machine label stiffness and the thickness of the material and the area of the label, so the Labeling machine in the use of soft film material should be appropriate to increase its thickness, generally controlled at 100μm or more. Labeling machine thin paper materials, such as 60 ~ 70g/m2 labeling paper, are generally not suitable for the production of large labels, but suitable for processing into small labels, such as price tags used on the price tag. Labeling machine label stiffness is not good, it will cause labeling out of the label, or label and backing paper reward so that the automatic labeling failure.

Peel-off force

Labeling machine peel-off force is the force at which the label is separated from the backing paper by the Labeling machine. The Labeling machine release force is related to the type and thickness of the adhesive, the silicone coating on the surface of the backing paper, and the ambient temperature at the time of labeling. If the Labeling machine release force is too small, the label will easily fall off (leave the backing paper) during the conveying process. The Labeling machine's release force is too large, the label will be difficult to detach from the backing paper, and it will not be able to produce labels. The Labeling machine should be integrated control of the technical indicators so that the release force is maintained within a reasonable range.

At the end of the paper

Is also an important indicator to control automatic labeling. The requirements of the Labeling machine base paper surface silicon-coated evenly, the Labeling machine peeling force is consistent. Uniform thickness and good tensile strength ensure that the Labeling machine will not break when labeling. Uniform thickness and good light transmission of the Labeling machine ensure that the sensor can correctly identify the location of the label.

Processing quality

Requires that both sides of the Labeling machine backing paper after slitting should be flat and free of fracture to avoid the backing paper from breaking when the tension changes. Labeling machine die-cutting, to avoid cutting through the backing paper or damage to the silicone layer. If the Labeling machine backing paper and silicone coated layer are destroyed, the Labeling machine backing paper will break easily or the glue in the label will penetrate the backing paper. In addition, the static electricity in the web label must be eliminated before Labeling machine labeling, because static electricity will lead to Labeling machine labeling failure or labeling inaccuracy.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. Before the Labeling machine leaves the factory, it will conduct a large number of tests on the Labeling machine to maintain the healthy development of the Labeling machine market. If you are interested in the Labeling machine, you can contact us, our website is www.cnzpack.com.

Liquid Filling Machine is a kind of process machinery, its process characteristics are more obvious, for the design requirements provided by the customer as well as the functions, work efficiency and other aspects of good, then Liquid Filling Machine what are the design principles and considerations? Let's learn about it together.

This is the content list:

l The design principle of Liquid Filling Machine

l Precautions for Liquid Filling Machine

The design principle of Liquid Filling Machine

First, design the parameters of the Liquid Filling Machine and the material to be filled, and then also to understand the container to be filled, to understand the shape of the container and the characteristics of the container cap, according to these characteristics design the corresponding bottle Liquid Filling Machine.

Secondly, we should also know the functions to be achieved by the Liquid Filling Machine, the principle and method of Liquid Filling Machine filling, the whole process of Liquid Filling Machine filling should be carefully understood, and each link should be designed reasonably and appropriately to avoid affecting the effect of filling.

Liquid Filling Machine should also be based on the specific needs of enterprises, the use of functional principles of innovative design methods to design filling equipment to meet the production needs of enterprises, which will not only improve efficiency but also reduce the rate of damage and reduce the production costs of enterprises.

Precautions for Liquid Filling Machine

First, check the Liquid Filling Machine itself to determine if the ball valve in the filling machine is damaged or loose. If the internal ball valve of the Liquid Filling Machine is the cause, the solution is to replace the internal ball valve. If the internal ball valve of the Liquid Filling Machine is damaged, there is no way to repair it, only to replace it with a new one.

Check that the Liquid Filling Machine syringe assembly is clean. If it is not clean, it will cause an unclean blockage between the inner and outer tubes, so remove the Liquid Filling Machine syringe, clean it and disinfect and maintain it.

Check that the Liquid Filling Machine filler nozzle is complete. If the Liquid Filling Machine filling nozzle is damaged, the equipment will leak during operation. Replace broken filling nozzles and inspect other filling nozzles for use, deterioration, or corrosion, and replace them as soon as possible.

Check whether the O-ring is corroded or worn. If the O-ring is corroded or worn, it will also cause the Liquid Filling Machine to drip. Therefore, in this case, it is recommended to replace the O-ring.

Check the Liquid Filling Machine barrel position. Determine if the cylinder is in the cylinder center support position, and also check if the Liquid Filling Machine cylinder piston and piston rod are secure, and if they are loose, please lock them. If the cylinder failure position is changed, you need to reinstall the cylinder and confirm the correct position.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, which has made great achievements in Liquid Filling Machine and is loved by the consumers. If you are interested in Liquid Filling Machine, you can contact us, our website is www.cnzpack.com.

In our production and life, Capping Machine is also called a Capping Machine, Capping Machine, or Capping Machine, which is used for screwing and unscrewing the caps of plastic bottles and glass bottles (molded bottles or tube bottles). equipment. Capping Machine is highly intelligent capping equipment with advanced technology, unique design, and easy operation. During the entire capping process, workers only need to place the cap on the mouth of the bottle, and then the bottle is automatically sent to the capping wheel and automatically tightened to complete the capping operation. The Capping Machine evacuates the packaging bottle and then tightens it, which prolongs the storage time of the packaging, reduces the failure rate of the Capping Machine, and improves the packaging efficiency of the Capping Machine. So what are the matters needing attention when operating Capping Machine correctly? Let's take a look together next.

This is the content list:

l Capping Machine rolling wheel adjustment

l Capping Machine lock wheel adjustment

l Capping Machine cap lock

l Capping Machine height adjustment

Capping Machine rolling wheel adjustment

Place the Capping Machine bottle on the bracket and raise the bracket to the highest point. First, loosen the lock nut to adjust the rolling wheel so that the (sprung) edge of the two Capping Machine rolling wheels is at the threading of the bottle. Click on it, then loosen the lock nut, and then adjust the adjusting screw so that the edges of the two rolling wheels are in contact with the cover, and a little pressure is appropriate, and then tighten the nut.

Capping Machine lock wheel adjustment

Adjust the two Capping Machine locking wheels, first loosen the locking nuts, adjust the locking wheels so that the edges of the two locking wheels are in contact with the lower edge of the bottle cap, a little pressure is appropriate, and then tighten the nuts (Note: Adjust Capping Machine Should be from loose to tight, adjust while pulling the lock).

Capping Machine cap lock

Loosen the top screw, remove the Capping Machine gland head, and then remove the entire Capping Machine lock head, install the appropriate plastic lock head on the cone sleeve, and then adjust the lifting height of the bracket to meet the working requirements.

Capping Machine height adjustment

Start the Capping Machine to lower the bracket to the lowest point, then place the bottle on the bracket, loosen the brake nut, turn the adjusting screw to raise the bracket, and then adjust the appropriate distance between the cap of the Capping Machine and the capping head (generally All are adjusted in place at the factory).

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. We have obtained ISO9001 quality management system certification, and some products have passed CE certification. Our company has obtained more than 20 invention patents and utility model patents. If you are interested in Capping Machine, you can contact us, our website is www.cnzpack.com.

Wenzhou Zungwan Intelligent Machine Co.,Ltd. is the professional equipment manufacturer to keep researching and developing the packing machinery for every type of liquid, powder, cream/ointment, fluid and half-fluid etc. materials. We have Obtained ISO9001 quality management system authentication and parts of our products have passed CE authentication. Our company has obtained more than 20 invention patents and utility model patents. The main products range from nail polish filling machine, perfume machine,perfume filling machine, powder serial automatically volume-measuring packing machine and inline capping machine, rotary capping machine and labeling machine, bottle unscrambler , screw capping machine ,tube filling and sealing machine, cartoning machine and other Packaging equipments.

So far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and our service as well as our integrity is acclaimed both in China and abroad. we will carry forward the spirit of "integrated innovation, and perseverance," discipline ourselves to be the first, and provide better and more perfect service for our new and old customers with enthusiasm and a new attitude.

Capping Machine operation, accuracy error, installation adjustment, equipment cleaning, maintenance, and other aspects are very simple and convenient. Capping Machine has been widely used in various industries such as daily chemical and grease, and can fill different high-viscosity fluids. So what are the working principles and structural characteristics of the Capping Machine? Let's take a look together next.

This is the content list:

l How Capping Machine works

l Structural characteristics of Capping Machine

How Capping Machine works

The Capping Machine adopts a new horizontal design, which is light and convenient and can automatically pump the material. For thicker slurry, a hopper can be added. When the Capping Machine is in the "auto" state, the Capping Machine will automatically perform continuous filling at a set speed. Capping Machines can be divided into three types: atmospheric filling machine, vacuum filling machine, and pressure filling machine.

Under normal pressure, Capping Machine can fill the liquid in a self-flowing manner according to the weight of the liquid itself. The filling method is to fill at a pressure greater than atmospheric pressure. The pressure in the liquid storage tank is greater than the pressure in the bottle, and the liquid that needs to be filled will enter the bottle depending on the pressure difference. The key component of the Capping Machine is the PLC operation control system. Under normal pressure, Capping Machine can fill the liquid in a self-flowing manner according to the weight of the liquid itself. The filling method is to fill at a pressure greater than atmospheric pressure. The pressure in the liquid storage tank is greater than the pressure in the bottle, and the liquid that needs to be filled will enter the bottle depending on the pressure difference. The key component of the Capping Machine is the PLC operation control system.

The principle of the Capping Machine is relatively easy to understand. The improved control system simplifies the structure of the machine. It can be seen from the operating conditions and control efficacy tests of the actual application that the automation level of the system has reached the design requirements. This reduces the labor intensity of the operator and makes the production line that needs filling production about 30% higher than before, so the probability of failure of the Capping Machine is significantly reduced.

Structural characteristics of Capping Machine

The design of the Capping Machine is very reasonable and appropriate, the remainder of the machine is very small, and the operation and use are very simple. The pneumatic parts inside the Capping Machine all use new pneumatic components. The piston and cylinder of the Capping Machine cylinder are made of polytetrafluoroethylene and stainless steel to meet the requirements of GMP testing. The filling quantity and filling speed of the Capping Machine can be adjusted at will, and the degree is relatively high.

The Capping Machine can be modified according to actual production needs. It can be transformed into a multi-head system, explosion-proof system, and overflow system. The Capping Machine is suitable for use in food, daily necessities, pesticides, and other industries, and has a broad application prospect.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. The company strictly controls the quality of the Capping Machine. If you are interested in Capping Machine, you can contact us, our website is www.cnzpack.com. I look forward to your coming and hope to cooperate with you.

The Pharmaceutical Filler and Capper is no stranger to the health care industry, after all, it has a major impact on it. Pharmaceutical Filler and Capper can specially package various products to ensure that they can be sold properly in the market. The Pharmaceutical Filler and Capper is no longer the traditional equipment that people know, but a smarter and more efficient one. So how does the new generation of Pharmaceutical Filler and Capper work? Let's take a look together.

This is the content list:

l Highlights of Pharmaceutical Filler and Capper

l Performance of the Pharmaceutical Filler and Capper

Highlights of Pharmaceutical Filler and Capper

First of all, the Pharmaceutical Filler and Capper are categorized so that they can provide the right equipment for the different needs of the pharmaceutical industry. Pharmaceutical Filler and Capper are divided into quantitative and fully automatic, both of which are very popular. Pharmaceutical Filler and Capper have an advanced control system, accurate filling quantity, reliable performance, and beautiful appearance, which is ideal for freeze-dried preparation, liquid preparation, and blood products. Pharmaceutical Filler and Capper are suitable for matching with the linkage production line. The filling volume is controlled by a computer, the filling accuracy of the peristaltic pump is high, the range of adjusting dose is large, and it is suitable for various viscosities. Pharmaceutical Filler and Capper's filling needle does not come into contact with the drug and is free of contamination. Peristaltic pump filling system is easy to clean and disinfect. No bottle is not filled, no bottle automatically stops and the bottle collapses. Pharmaceutical Filler and Capper automatically display and counts. A filling system with shrinkage function, no drip. Equipped with Mitsubishi frequency conversion mechanism. Variable frequency speed regulation. The whole machine is designed according to GMP requirements. The equipment tends to be intelligent to make the filling process easier.

Performance of Pharmaceutical Filler and Capper

Pharmaceutical Filler and Capper's performance is good on the one hand, Pharmaceutical Filler and Capper have a wide range of use, can have a certain degree of fluidity of the powder-like, granular materials for reasonable packaging. The Pharmaceutical Filler and Capper can automatically track and correct the error caused by the change of material specific gravity and material level by photoelectric switch control. Pharmaceutical Filler and Capper are simple in design, made of stainless steel, easy to clean, and more convenient for users to use.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, the quality of our Pharmaceutical Filler and Capper and services and our integrity is widely praised at home and abroad, we have obtained ISO9001 quality management system certification, and some of our products have passed CE certification. Wenzhou Zongwan Intelligent Machinery Co., Ltd. has obtained more than 20 invention patents and utility model patents. If you are interested in Pharmaceutical Filler and Capper, you can contact us at www.cnzpack.com. We are looking forward to your visit and hope to cooperate with you.

ZUNGWAN is the leading manufacturer of perfume and cosmetic filling machines and lines, providing all solutions from the smallest to the fastest machines (400 bpm) for a vast range of applications :

Perfumes (bottles, samples, miniatures), liquid Cosmetics (shampoo, conditioner, lotions, gel, serum, foam bath, liquid soap, shower gel, hair dye, nail varnish, foundation, makeup remover, suntan lotion, deodorant, roll-on, etc.) and Cosmetic creams (jars, lip-gloss, mascara).

Automatic Jar Washing Filling and Capping Machine In line with clients' diverse requirements across the globe, we are offering an excellent range of Jar Auto Filling Machine . This machine is designed at our hi-tech manufacturing unit using the outstanding quality components and contemporary technology in relevance to the international standards.

Our cosmetic line of filling equipment will accurately dispense products that are water-thin …

3 Side Seal Flow Wrap Machine Face Mask Packaging 3 Side Seal Flow Wrap Machine Face Mask Packaging Model: PPD-3FFP Output: 40-230 bags/min Bag size: 220mm×140mm Film...

12 nozzle Eyebrow Pencil Force Filling Machine , Cosmetics Filling Equipment; High Precision Cosmetic Eyebrow Pencil Filling Machine With bottom force filling system; Liquid Eyebrow …

Ultrasonic Tube Filling Sealing Machine ZH-006 Ultrasonic sealing machine is advanced …

Semi-automatic tube filling and sealing machine NTT-200 is used for filling of tubes with gels, sealing, stamping, cutting excess plastic on tube ending. Contact Us Send Inquiry 5458 products Tags: Semi Automatic Tube Filling And Sealing Machine

Tube Filling And Sealing Machine ( This video introduces )Tube Filling And Sealing Machine: …

Catchup packing machine tomato paste pouch tomato sauce packing machine