











We know that Labeling Machine brings great convenience to our production and life, so what are the working principles and performance characteristics of Labeling Machine? Let's go take a look next.
This is the content list:
l How the Labeling Machine works
l Performance characteristics of Labeling Machine
How the Labeling Machine works
First of all, the working principle of the Labeling Machine is to put the roll of labels in place, and then put the round bottle on the conveyor belt. The labeling head of the Labeling Machine is set at a fixed distance. The labeling wheel and the rotating shaft are used to move the label. Separate from the base film, it should be noted that the Labeling Machine label tape needs to be kept in a constant state during this operation.
Then, the Labeling Machine conveyor belt pushes the round bottle. When it is transferred to the area, the driving wheel will slow down and stop applying the label to the bottle. The Labeling Machine logo can be applied to the entire bottle or half of the bottle. The basic working principle is the same.
The above is the working principle of the Labeling Machine. At present, Labeling Machine has been widely used in the market, gradually replacing manual labeling, and the labeling speed of the prototype Labeling Machine is much higher than that of manual operation, and the accuracy is also higher. The cost of manual operation is lower than that of manual operation. Therefore, the circular Labeling Machine is more demanded by consumers.
Performance characteristics of Labeling Machine
1. The Labeling Machine is equipped with a double-labeling mechanism. Labeling Machine to ensure the accuracy of labeling, Labeling Machine double extrusion labeling can effectively eliminate air bubbles, to ensure that the label head and tail are tightly attached.
2. Labeling Machine intelligent control, automatic photoelectric tracking, Labeling Machine with no labeling, no label automatic correction and automatic detection of the label function, Labeling Machine to avoid wasting labels and missing labels.
3. Labeling Machine with elastic pressure top mechanism to ensure stable product delivery, Labeling Machine effectively eliminates the inherent error of the bottle height.
4. The Labeling Machine is equipped with an automatic bottle splitting mechanism, which automatically separates the spacing before the bottle guide, Labeling Machine to ensure the stability of the subsequent bottle guide, conveying, and labeling.
5. The Labeling Machine adopts a double-sided hard plastic synchronous guide chain to automatically ensure the neutrality of the bottle.
6. Labeling Machine has little requirement for workers to put bottles and assembly line to receive bottles, which greatly reduces the difficulty of workers' work or assembly line docking. Labeling Machines can be produced on a single machine or connected with assembly-line production.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It strictly controls the production of Labeling Machines and uses the working principle and performance characteristics of Labeling Machines to produce Labeling Machines that are more in line with consumer needs. If you are interested in Labeling Machines, you can contact us, our website is www.cnzpack.com.
After the Labeling machine sensor sends a signal that the labeling object is ready to be labeled, the drive wheel on the Labeling machine turns up. As the rolled label is in a tight state on the equipment, when the Labeling machine backing paper is tightly attached to the peeling plate and changes direction, the Labeling machine label is forced to disengage due to the rigidity of its material and is ready to be labeled. At this time, the labeling object is located just below the label, under the action of the labeling wheel, to achieve synchronous labeling. After the Labeling machine has finished labeling, the sensor under the roll label sends a stop signal, the drive wheel comes to a standstill, and a labeling cycle end. No matter which type of Labeling machine, the labeling process is roughly the same. The difference is that the installation position of the Labeling machine is different, the labeling object is conveyed differently and positioned differently, and the form of the labeling roller of the Labeling machine is also different. So, what are the Labeling machine's requirements for labels? Let's look at it together next.
This is the content list:
l Surface material
l Release force
l At the end of the paper
l Processing quality
Surface material
Labeling machine label stiffness is the key to labeling, so the Labeling machine surface material is required to have a certain strength and hardness. Labeling machine label stiffness and the thickness of the material and the area of the label, so the Labeling machine in the use of soft film material should be appropriate to increase its thickness, generally controlled at 100μm or more. Labeling machine thin paper materials, such as 60 ~ 70g/m2 labeling paper, are generally not suitable for the production of large labels, but suitable for processing into small labels, such as price tags used on the price tag. Labeling machine label stiffness is not good, it will cause labeling out of the label, or label and backing paper reward so that the automatic labeling failure.
Peel-off force
Labeling machine peel-off force is the force at which the label is separated from the backing paper by the Labeling machine. The Labeling machine release force is related to the type and thickness of the adhesive, the silicone coating on the surface of the backing paper, and the ambient temperature at the time of labeling. If the Labeling machine release force is too small, the label will easily fall off (leave the backing paper) during the conveying process. The Labeling machine's release force is too large, the label will be difficult to detach from the backing paper, and it will not be able to produce labels. The Labeling machine should be integrated control of the technical indicators so that the release force is maintained within a reasonable range.
At the end of the paper
Is also an important indicator to control automatic labeling. The requirements of the Labeling machine base paper surface silicon-coated evenly, the Labeling machine peeling force is consistent. Uniform thickness and good tensile strength ensure that the Labeling machine will not break when labeling. Uniform thickness and good light transmission of the Labeling machine ensure that the sensor can correctly identify the location of the label.
Processing quality
Requires that both sides of the Labeling machine backing paper after slitting should be flat and free of fracture to avoid the backing paper from breaking when the tension changes. Labeling machine die-cutting, to avoid cutting through the backing paper or damage to the silicone layer. If the Labeling machine backing paper and silicone coated layer are destroyed, the Labeling machine backing paper will break easily or the glue in the label will penetrate the backing paper. In addition, the static electricity in the web label must be eliminated before Labeling machine labeling, because static electricity will lead to Labeling machine labeling failure or labeling inaccuracy.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. Before the Labeling machine leaves the factory, it will conduct a large number of tests on the Labeling machine to maintain the healthy development of the Labeling machine market. If you are interested in the Labeling machine, you can contact us, our website is www.cnzpack.com.
In our production and life, the Liquid Filling Machine has a significant impact on many industries, so what is the method of using the Liquid Filling Machine? Let's go take a look next.
This is the content list:
l The ground wire must be well-grounded before the Liquid Filling Machine works
l Liquid Filling Machine liquid filling system assembly
The ground wire must be well-grounded before the Liquid Filling Machine works.
The ground wire must be well-grounded before the Liquid Filling Machine works, and then the appropriate standard syringe must be selected according to the different filling volumes. Generally, a 1ml syringe is used when the dispensing range is 0.2-1ml. Use a 5ml syringe for 1-5ml.use a 10ml syringe for 5-10ml. The 20ml model uses a 20ml glass infusion device. The 100ml model uses a 100ml glass infusion device, and the 500ml model uses the stainless steel filling system produced by our factory.
Liquid Filling Machine liquid filling system assembly
Pull out the inner core of the Liquid Filling Machine syringe, put the screw sleeve on the inner core of the syringe, and use the screw sleeve to properly fasten it to the lower base (cleanliness must be paid when disassembling the syringe). Place the upper clamp seat on the outlet end of the Liquid Filling Machine syringe jacket, and properly tighten the nuts on both sides to assemble the inner core and outer jacket of the installed Liquid Filling Machine syringe into one body. At this point, the Liquid Filling Machine injection system is assembled.
Place the Liquid Filling Machine valve with the arrow facing upwards and the arrow mark facing outwards and fix it on the fixing screw with a nut. Assemble the Liquid Filling Machine with a complete liquid filling system, align the upper and lower round holes of the liquid filling system components with the upper and lower fixing rods respectively, and put them on the bearing so that the outer end surface and the bearing surface are levels. When assembling the lower end, do not make the screw sleeve and the crank touch to prevent abnormal noise when the crank on the Liquid Filling Machine rotates (the screw sleeve and the crank are about 1mm apart when installed correctly). After the liquid filling system is installed correctly, tighten it. Tighten the screws up and down. Use a short hose to connect the Liquid Filling Machine syringe to the valve connection nozzle. The liquid inlet pipe is connected to the water inlet, and the liquid outlet pipe is connected to the water outlet. To prevent the liquid inlet and outlet pipes from being entangled, clip the liquid inlet and outlet pipes into the ear openings on the side of the casing.
Turn the crank of the Liquid Filling Machine by hand, it should be able to rotate freely, otherwise, the assembly is wrong, you should check whether the Liquid Filling Machine injection system is fastened to the rotating bearing.
Our company has obtained more than 20 invention patents and utility model patents. The main products are a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and online capping machine, capping machine and labeling machine, bottle unscrambler, tube filling and sealing machine, Cartoning machines, and other packaging equipment. If you are interested in Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.
Capping Machine is filling equipment specially designed for new oral liquid easy-pull bottles. The design is reasonable, the structure is simple, the operation is convenient, and a mechanical stop filling device is provided for lack of bottles. So what are the adjustment methods of the Capping Machine? Let's take a look together next.
This is the content list:
l Capping Machine feeding half adjustment
l Matters needing attention in discharging
l Adjustment of the locking device
l Vibrator adjustment
Capping Machine feeding half adjustment
Adjust the bottle blocking plate on the feeding half of the Capping Machine upwards to shorten the adaptation to the bottle feeding stroke. Adjust downwards to make the Capping Machine adapt to the extension of the bottle feeding stroke. Adjust the positioning bottle position left and right to align the bottle position when the movable tooth is running, so that the bottle can be fed into the positioning tooth smoothly. Adjust the bottle blocking plate of the Capping Machine so that the width of the bottle inlet is about 22 mm.
Adjust the perfusion Capping Machine component. The role of the perfusion Capping Machine component is to make the liquid medicine be delivered to each easy-pull bottle in time through the dosing device, one-way valve, and needle. Therefore, the needle must enter the bottle mouth properly and the filling time must be appropriate. Adjust the Capping Machine side cam to rotate clockwise or counterclockwise so that the needle is inserted into the bottle mouth just after the empty bottle enters the toothed position. And lift the needle before leaving the toothed position. The filling time of the Capping Machine is adjusted. Turn the cam clockwise or reverse the adjustable needle into the bottle mouth and start filling immediately, and stop filling before the needle leaves the bottle mouth.
Matters needing attention in discharging
Since the Capping Machine is an easy-pull bottle filling and locking device, the discharging has been capped and sealed. To prevent the locked bottle from overturning, it must be placed on the Capping Machine discharge hopper before the first bottle is discharged. Several empty bottles can be transported to the discharge hopper smoothly to keep the locked bottles and sent to the next process with the bottle hopper.
Adjustment of the locking device
Capping Machine capping time adjustment, adjust the cam rotation angle. When the filling liquid bottle enters the locking tooth position, the locking shaft has moved and left the bottle cap before the moving tooth approaches the bottle. The capping pressure is adjusted, and the capping pressure is adjusted. The size of the cap pressure is directly related to the quality of the lock. If the pressure is too high to break the easy-pull bottle, and the pressure is too small, it will affect the sealing performance. Therefore, the nut should be adjusted according to the actual average height of the easy-pull bottle to adjust the pressure to the best.
Capping Machine blade action time adjustment, the blade should be close to the bottleneck before the end of the capping, otherwise, the locking effect of some short bottles cannot be achieved. Loosen the nut during adjustment, and adjust the shaft and up and down to make the blade action time sooner or later. When adjusting the lock of the Capping Machine, pay attention to the locking of the nuts after the adjustment of each department. The easy-pull bottle must be used for the initial valve test. The average height must be taken. Irregular easy-pull bottles cannot enter the lock to avoid damage to the parts.
Vibrator adjustment
The Capping Machine adopts the principle of electromagnetic oscillation to drop the bottle cap to the proper position along the track according to a certain movement trajectory. The vibrator is packaged separately when it leaves the factory, and the lower rail opening must be aligned with the movement rail of the easy-pull bottle when installed. To adjust the gap between the magnets of the Capping Machine, loosen the screw, open the cover, adjust the nut, and make the vibration of the Capping Machine low and fast.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It strictly controls the production of the Capping Machine. A large number of factory tests are carried out before Capping Machine leaves the factory to ensure product quality. If you are interested in Capping Machine, you can Contact Us, our website is www.cnzpack.com.
Korea East Asia Pharmaceutical Company, ordered a syrup filling line from our company, from bottle management - bottle washing - filling - corking - capping - labeling, the whole line in the Korean factory to complete the commissioning task, the whole line production design speed of 120 bottles per minute high-speed filling line.
The Cosmetic Filling machine And Capping machine integrates the functions of air purification, filling, inserting, capping, and venting. It is suitable for filling water injection, lotion, and cream products. The Cosmetic Filling machine And Capping machine has the advantages of reasonable design, stable performance, accurate quantity, glass tabletop, automatic bottle feeding, smooth operation and no noise, electric speed regulation of filling speed and filling volume, and convenient maintenance and cleaning. Next, let's take a look at the description and structural characteristics of the Cosmetic Filling machine And capping Machine. Here are some answers.
Here is the content list:
Description of Cosmetic Filling machine And Capping machine.
Structural characteristics of Cosmetic Filling machine And Capping machine.
The Cosmetic Filling machine And Capping machine adopts automatic low-vacuum filling, automatic bottle detection (no bottle no filling), three fillings, automatic lowering of the nozzle cap, circulation of the perfume bottle die, and wide adaptability. It can meet the volume of containers of different sizes and filling requirements. Cosmetic Filling Machine And Capping machine is equipped with air bottle cleaning, quantitative filling, negative pressure filling, pumping, roll cap, jacket, screw cap, rejection, labeling, and finished product collection. The mold moves in a circular motion, which makes it easy to change the bottle. The stepper motor is used for quantitative filling, and the filling volume can be adjusted quickly. The negative pressure device is used to fill the same liquid level and the manipulator releases the pump to increase the pump roll rate; the elastic rolling head is to avoid damage to the bottle body.
The design of the Cosmetic Filling machine And Capping machine is very reasonable. The Cosmetic Filling machine And Capping machine has a reasonable and compact structure, stable operation, flexible operation, and convenient specification conversion and adjustment. The speed of the aluminum cover is adjustable. Using the principle of seven-station three-knife cap rolling, the aluminum cap is rolled without damage, and the rolling mouth is firm, smooth and flat. The operation of the machine is very simple. The internal pneumatic part adopts new pneumatic components. The piston and cylinder of cylinder are made of PTFE and stainless steel, which meets the requirements of GMP testing. The filling speed can be adjusted at will with high precision. The Cosmetic Filling machine And Capping machine can be modified according to actual production needs and can be transformed into a multi-head type, explosion-proof type, and overflow type system.
Wenzhou Zungwan Intelligent Machine Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream, ointment, fluid, and semi-fluid materials. Our official website is https:// www. cnzpack.com/. If you are engaged in work related to Cosmetic Filling machines And Capping machines or want to learn more about our company, you can communicate with us on the website. Our company adheres to the service tenet of "customer first", and implements the service of honesty and customer first.
Capping Machine operation, accuracy error, installation adjustment, equipment cleaning, maintenance, and other aspects are very simple and convenient. Capping Machine has been widely used in various industries such as daily chemical and grease, and can fill different high-viscosity fluids. So what are the working principles and structural characteristics of the Capping Machine? Let's take a look together next.
This is the content list:
l How Capping Machine works
l Structural characteristics of Capping Machine
How Capping Machine works
The Capping Machine adopts a new horizontal design, which is light and convenient and can automatically pump the material. For thicker slurry, a hopper can be added. When the Capping Machine is in the "auto" state, the Capping Machine will automatically perform continuous filling at a set speed. Capping Machines can be divided into three types: atmospheric filling machine, vacuum filling machine, and pressure filling machine.
Under normal pressure, Capping Machine can fill the liquid in a self-flowing manner according to the weight of the liquid itself. The filling method is to fill at a pressure greater than atmospheric pressure. The pressure in the liquid storage tank is greater than the pressure in the bottle, and the liquid that needs to be filled will enter the bottle depending on the pressure difference. The key component of the Capping Machine is the PLC operation control system. Under normal pressure, Capping Machine can fill the liquid in a self-flowing manner according to the weight of the liquid itself. The filling method is to fill at a pressure greater than atmospheric pressure. The pressure in the liquid storage tank is greater than the pressure in the bottle, and the liquid that needs to be filled will enter the bottle depending on the pressure difference. The key component of the Capping Machine is the PLC operation control system.
The principle of the Capping Machine is relatively easy to understand. The improved control system simplifies the structure of the machine. It can be seen from the operating conditions and control efficacy tests of the actual application that the automation level of the system has reached the design requirements. This reduces the labor intensity of the operator and makes the production line that needs filling production about 30% higher than before, so the probability of failure of the Capping Machine is significantly reduced.
Structural characteristics of Capping Machine
The design of the Capping Machine is very reasonable and appropriate, the remainder of the machine is very small, and the operation and use are very simple. The pneumatic parts inside the Capping Machine all use new pneumatic components. The piston and cylinder of the Capping Machine cylinder are made of polytetrafluoroethylene and stainless steel to meet the requirements of GMP testing. The filling quantity and filling speed of the Capping Machine can be adjusted at will, and the degree is relatively high.
The Capping Machine can be modified according to actual production needs. It can be transformed into a multi-head system, explosion-proof system, and overflow system. The Capping Machine is suitable for use in food, daily necessities, pesticides, and other industries, and has a broad application prospect.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. The company strictly controls the quality of the Capping Machine. If you are interested in Capping Machine, you can contact us, our website is www.cnzpack.com. I look forward to your coming and hope to cooperate with you.
Wenzhou Zungwan Intelligent Machine Co.,Ltd. is the professional equipment manufacturer to keep researching and developing the packing machinery for every type of liquid, powder, cream/ointment, fluid and half-fluid etc. materials. We have Obtained ISO9001 quality management system authentication and parts of our products have passed CE authentication. Our company has obtained more than 20 invention patents and utility model patents. The main products range from nail polish filling machine, perfume machine,perfume filling machine, powder serial automatically volume-measuring packing machine and inline capping machine, rotary capping machine and labeling machine, bottle unscrambler , screw capping machine ,tube filling and sealing machine, cartoning machine and other Packaging equipments.
So far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and our service as well as our integrity is acclaimed both in China and abroad. we will carry forward the spirit of "integrated innovation, and perseverance," discipline ourselves to be the first, and provide better and more perfect service for our new and old customers with enthusiasm and a new attitude.