











In our production and life, Capping Machine is also called a Capping Machine, Capping Machine, or Capping Machine, which is used for screwing and unscrewing the caps of plastic bottles and glass bottles (molded bottles or tube bottles). equipment. Capping Machine is highly intelligent capping equipment with advanced technology, unique design, and easy operation. During the entire capping process, workers only need to place the cap on the mouth of the bottle, and then the bottle is automatically sent to the capping wheel and automatically tightened to complete the capping operation. The Capping Machine evacuates the packaging bottle and then tightens it, which prolongs the storage time of the packaging, reduces the failure rate of the Capping Machine, and improves the packaging efficiency of the Capping Machine. So what are the matters needing attention when operating Capping Machine correctly? Let's take a look together next.
This is the content list:
l Capping Machine rolling wheel adjustment
l Capping Machine lock wheel adjustment
l Capping Machine cap lock
l Capping Machine height adjustment
Capping Machine rolling wheel adjustment
Place the Capping Machine bottle on the bracket and raise the bracket to the highest point. First, loosen the lock nut to adjust the rolling wheel so that the (sprung) edge of the two Capping Machine rolling wheels is at the threading of the bottle. Click on it, then loosen the lock nut, and then adjust the adjusting screw so that the edges of the two rolling wheels are in contact with the cover, and a little pressure is appropriate, and then tighten the nut.
Capping Machine lock wheel adjustment
Adjust the two Capping Machine locking wheels, first loosen the locking nuts, adjust the locking wheels so that the edges of the two locking wheels are in contact with the lower edge of the bottle cap, a little pressure is appropriate, and then tighten the nuts (Note: Adjust Capping Machine Should be from loose to tight, adjust while pulling the lock).
Capping Machine cap lock
Loosen the top screw, remove the Capping Machine gland head, and then remove the entire Capping Machine lock head, install the appropriate plastic lock head on the cone sleeve, and then adjust the lifting height of the bracket to meet the working requirements.
Capping Machine height adjustment
Start the Capping Machine to lower the bracket to the lowest point, then place the bottle on the bracket, loosen the brake nut, turn the adjusting screw to raise the bracket, and then adjust the appropriate distance between the cap of the Capping Machine and the capping head (generally All are adjusted in place at the factory).
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. We have obtained ISO9001 quality management system certification, and some products have passed CE certification. Our company has obtained more than 20 invention patents and utility model patents. If you are interested in Capping Machine, you can contact us, our website is www.cnzpack.com.
Capping Machine operation, accuracy error, installation adjustment, equipment cleaning, maintenance, and other aspects are very simple and convenient. Capping Machine has been widely used in various industries such as daily chemical and grease, and can fill different high-viscosity fluids. So what are the working principles and structural characteristics of the Capping Machine? Let's take a look together next.
This is the content list:
l How Capping Machine works
l Structural characteristics of Capping Machine
How Capping Machine works
The Capping Machine adopts a new horizontal design, which is light and convenient and can automatically pump the material. For thicker slurry, a hopper can be added. When the Capping Machine is in the "auto" state, the Capping Machine will automatically perform continuous filling at a set speed. Capping Machines can be divided into three types: atmospheric filling machine, vacuum filling machine, and pressure filling machine.
Under normal pressure, Capping Machine can fill the liquid in a self-flowing manner according to the weight of the liquid itself. The filling method is to fill at a pressure greater than atmospheric pressure. The pressure in the liquid storage tank is greater than the pressure in the bottle, and the liquid that needs to be filled will enter the bottle depending on the pressure difference. The key component of the Capping Machine is the PLC operation control system. Under normal pressure, Capping Machine can fill the liquid in a self-flowing manner according to the weight of the liquid itself. The filling method is to fill at a pressure greater than atmospheric pressure. The pressure in the liquid storage tank is greater than the pressure in the bottle, and the liquid that needs to be filled will enter the bottle depending on the pressure difference. The key component of the Capping Machine is the PLC operation control system.
The principle of the Capping Machine is relatively easy to understand. The improved control system simplifies the structure of the machine. It can be seen from the operating conditions and control efficacy tests of the actual application that the automation level of the system has reached the design requirements. This reduces the labor intensity of the operator and makes the production line that needs filling production about 30% higher than before, so the probability of failure of the Capping Machine is significantly reduced.
Structural characteristics of Capping Machine
The design of the Capping Machine is very reasonable and appropriate, the remainder of the machine is very small, and the operation and use are very simple. The pneumatic parts inside the Capping Machine all use new pneumatic components. The piston and cylinder of the Capping Machine cylinder are made of polytetrafluoroethylene and stainless steel to meet the requirements of GMP testing. The filling quantity and filling speed of the Capping Machine can be adjusted at will, and the degree is relatively high.
The Capping Machine can be modified according to actual production needs. It can be transformed into a multi-head system, explosion-proof system, and overflow system. The Capping Machine is suitable for use in food, daily necessities, pesticides, and other industries, and has a broad application prospect.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. The company strictly controls the quality of the Capping Machine. If you are interested in Capping Machine, you can contact us, our website is www.cnzpack.com. I look forward to your coming and hope to cooperate with you.
ZUNGWAN is the leading manufacturer of perfume and cosmetic filling machines and lines, providing all solutions from the smallest to the fastest machines (400 bpm) for a vast range of applications :
Perfumes (bottles, samples, miniatures), liquid Cosmetics (shampoo, conditioner, lotions, gel, serum, foam bath, liquid soap, shower gel, hair dye, nail varnish, foundation, makeup remover, suntan lotion, deodorant, roll-on, etc.) and Cosmetic creams (jars, lip-gloss, mascara).
There is already a lot of knowledge about the Labeling Machine in the market, but the Labeling Machine will appear crooked in the process of using it. How should this be solved? Let's take a look together next.
This is the content list:
Reasons for Labeling Machine crooked during use
Labeling Machine appears to "post crooked" solution
Why does Labeling Machine post crookedly during use? There are two factors: one is running in an environment that is not suitable for Labeling Machine work, and the other is the lack of maintenance of Labeling Machine equipment. The round Labeling Machine adopts self-adhesive roll labeling paper, and the labeling adopts the rolling method to complete the labeling process. The self-adhesive Labeling Machine is clean and hygienic, non-mold, beautiful, and firm after labeling, and will not fall off by itself, and production efficiency Higher merits. If you can do both of these things, you can eliminate the problem of inaccurate labeling.
First, stop the Labeling Machine, and then inspect whether the labeling heads on both sides of the Labeling Machine are loose. Use the tools configured by the manufacturer to stabilize the Labeling Machine. Check whether the Labeling Machine wraps the label's trays for looseness or uneven rotation speed. Add engine oil to lubricate. Round bottle Labeling Machine realizes labeling or filming on the circumferential surface of cylindrical and conical products, such as glass bottles, plastic bottles, etc. It can realize circumferential, semicircular, circumferential double-sided, circumferential positioning labeling and other functions, mainly vertical There are two ways of labeling and horizontal labeling. Then inspect the parameters of the Labeling Machine operating system to avoid labeling different products under the same parameters of the Labeling Machine. Finally, adjust the labeling head and place the labeling product separately. When the conveyor belt is conveyed, whether the Labeling Machine shakes or shakes the first two These steps must be performed after the Labeling Machine stops. If the above two cannot solve the labeling problem of the Labeling Machine, please do not disassemble and replace the internal parts of the device privately. You need to transfer the professional to repair the Labeling Machine.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. So far, we have more than 100 domestic customers and more than 400 foreign customers. The quality of our Labeling Machine and service as well as our integrity are widely praised at home and abroad. We will carry forward the spirit of "comprehensive innovation and perseverance", self-discipline and strive for the first place, and provide new and old customers with better and more complete services with enthusiasm and a new attitude. It can be seen that we have developed well in the quality of Labeling Machine products. Labeling Machine's first-class product quality and efficient and fast after-sales service have created excellent products of "Zhonghuan". If you are interested in Labeling Machine, you can contact us, our website is www.cnzpack.com. I look forward to your coming and hope to cooperate with you.
In our production and life, the Cartoning Machine is of great significance to us, but sometimes, the Cartoning Machine will fail, so what is the reason for the failure of the Cartoning Machine? Next, let us analyze it together.
This is the content list:
Stop or stop between conveyor belts
The carton cannot be sucked down
The carton is not formed or ejected at the mouth of the box feeding template after being sucked
Can't suck the instructions
The paper rebounds during the suction process of the manual
The manual does not fold well
Uneven folding of the manual
There are curls and creases after the manual is folded
Manual stuck in the fence
1. Cartoning Machine shuts down at intervals to check if there is a shortage of materials and automatically starts up when supplemented.
2. Shut down the Cartoning Machine to check whether the power supply including the power supply part, the motor, or the governor is normal.
1. Whether the cartons of Cartons Machine are arranged neatly.
2. Whether the cartons of the Cartoning Machine are pasted together.
3. Whether the air pressure of the Cartoning Machine suction head is normal.
1. Check if the cartons of Cartons Machine are too hard.
2. Check whether the position of the guide rod of the cartons placed by the Cartoning Machine and the box delivery template are not correct.
3. Check whether the small hook spring at the rear of the Cartoning Machine delivery template is deformed.
4. Check if the height of the suction head of the Cartoning Machine and the box delivery track is correct.
1. Whether the Cartoning Machine manual is deformed, causing the suction head to fail to suck.
2. Whether the suction head gas of the Cartoning Machine is parallel to the manual.
3. Whether the paper width of the Cartoning Machine manual is different, the error must be within 1mm. The stacking position of the manual should be adjusted to a difference of 0.5mm from the inner edge when the suction head rises to the high position.
4. The small paper-separating hook above the suction head of the Cartoning Machine origami moves too early. Generally, the small hook should be inserted into the gap between the paper and the paper before the suction head is about to drop. The height of the small hook is adjusted to be 0.5mm away from the suction head when it is in the high position.
1. The foot-lifting action of the Cartoning Machine's manual was too early, and the manual was taken away by the foot support before being pulled down. The position of the feet of the Cartoning Machine is so that it does not touch the sucked manual when it is returned and it returns to the high position when the paper picking notch wheel has not pulled the paper.
2. Whether the matching speed of the Cartoning Machine suction head and paper picking wheel is the same. The suction head of the Cartoning Machine should be lowered first, and then the front part of the paper picking notch wheel should be pressed onto the paper.
1. Check if the Cartoning Machine paper is deformed and bent, and if there are burrs.
2. Is there any foreign matter in the fence of the Cartoning Machine blocking the paper?
3. The gap between the opening of the Cartoning Machine fence and the folding stick is too large, causing the paper to come out.
4. Is the gap between Cartons Machine's folding sticks too large to hold the paper? Adjust the adjusting screws at both ends of the folding stick to reduce the gap. If the Cartoning Machine folding stick has been used for too long and worn out, the folding stick must be replaced.
Check the Cartoning Machine to adjust the front and rear positions of the barriers in the fence to achieve the required folding size.
1. Is the gap between the Cartoning Machine baffle and the folding stick too large? Adjust the middle position of the baffle and folding stick.
2. If the middle position of the Cartoning Machine baffle and the folding stick has been adjusted, and there is still a large gap, remove the positioning pins on the Cartoning Machine baffle and re-adjust until the gap does not feed paper.
1. Whether the paper feeding gap of Cartoning Machine folding stick is too large and paper feeding is weak. The adjustment method is the same as above.
2. The installation position of the lower half of the Cartoning Machine fence is too long than the arc guide plate on it so that the paper cannot enter the folding stick below. Loosen all the fixing screws on the Cartoning Machine fence and adjust the board backward, but it should not be shorter than the upper guide plate and should be 1-3 mm longer than the guide plate. If it is shorter than the guide plate, the Cartoning Machine manual may go directly into the folding stick below without folding.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It will conduct a large number of tests before the Cartoning Machine leaves the factory to reduce the failure of the Cartoning Machine and provide warranty services. If you are interested in the Cartoning Machine, you can contact us Contact, our website is www.cnzpack.com.
With the increasingly fierce competition in the manufacturing and production of plastic bottles in the food and pharmaceutical industries, Bottle Unscrambler has become more and more solid backing for the food and pharmaceutical plastic bottle markets. So how does it play a role? We will introduce the work process and personnel operation specifications of Bottle Unscrambler. Let's take a look together next.
This is the content list:
The workflow of Bottle Unscrambler
Personnel operation specification of Bottle Unscrambler
The workflow of Bottle Unscrambler is generally as follows: manually put materials into the storage bottle library, the materials in the storage bottle library will be automatically quantified and fed to the turntable at the set speed. The turntable rotates at a high speed to supply the bottles as required, the web wheel The irregular bottles are removed, and the bottle dividing part sends the bottles from the turntable to the bottle unscramble part at a certain speed. The Bottle Unscrambler part of the Bottle Unscrambler clamps the bottles to the working surface of the conveyor through the conveyor belts on both sides, and at the same time sorts the bottles through the bottle turner. The Bottle Unscrambler electronic control system performs real-time monitoring and feedback through the sensors of each part to achieve fully automated operation requirements, and save a lot of labor costs and avoid losses caused by human error factors.
To ensure the normal and safe operation of Bottle Unscrambler, there are special operating procedures established for it. Operators and equipment management personnel shall perform standardized operations of Bottle Unscrambler under these procedures. This safe operation specification is commonly used in Bottle Unscramblers, mixers, high-speed automatic Bottle Unscramblers, etc.
1. First check the Bottle Unscrambler's intact, clean, and expiration status identification and the equipment operation record of the shift. If the inspection finds that the Bottle Unscrambler has exceeded the cleaning validity period, it is necessary to further clean the equipment according to the equipment cleaning operation rules and fill in the equipment status identification.
2. Check the Bottle Unscrambler and the Bottle Unscrambler to confirm that there is no foreign matter, and turn the bottle plate and unscrambler to confirm that it can work normally.
3. Turn on the Bottle Unscrambler power switch, check the touch screen and three photoelectric switches. If both are energized, the lack of a bottle alarm will be displayed on the touch screen. When the electric eye is blocked by hand, the screen displays the blocking alarm, and the two photoelectric switches are in a normal state.
4. Turn on the Bottle Unscrambler compressed air, use the bottom of the bottle to shake under the electric eye of the bottle puller, compressed air will be sprayed out, and the equipment can be turned on normally.
To ensure that the various parts of the Bottle Unscrambler can work normally, the formal operation can be divided into five steps: click the host start and lift start on the touch screen respectively, and observe whether the Bottle Unscrambler has abnormal noise when it is running. After powering on the Bottle Unscrambler and confirming that there is no abnormal condition, stop the device, but the qualified infusion bottle upright in the bottle feeding bracket, and start the device again. The bottle will pass through the rotating carousel of the device and enter the conveyor belt to start the bottle unscramble operation. Run at low speed when starting up, and then adjust the lifting speed and unscramble speed according to the actual production, so that the speed of the Bottle Unscrambler equipment can match the actual production speed. To prevent such phenomena from happening. If such a phenomenon occurs, stop the machine immediately to eliminate the fault before it can continue to run. During the operation of the equipment, the bottles should be put in continuously, and observe whether there are phenomena such as pouring, jamming, broken bottles, etc. If any, stop the machine immediately and start the production after troubleshooting. After the production is over, stop the equipment, turn off the power of the Bottle Unscrambler, and clear the remaining materials out of the equipment.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. When the Liquid Filling Machine leaves the factory, it will provide customers with detailed Liquid Filling Machine operation procedures and operating specifications. If you are interested in Liquid Filling Machine, you can contact us, our website is www.cnzpack.com.
Wenzhou Zungwan Intelligent Machine Co.,Ltd. is the professional equipment manufacturer to keep researching and developing the packing machinery for every type of liquid, powder, cream/ointment, fluid and half-fluid etc. materials. We have Obtained ISO9001 quality management system authentication and parts of our products have passed CE authentication. Our company has obtained more than 20 invention patents and utility model patents. The main products range from nail polish filling machine, perfume machine,perfume filling machine, powder serial automatically volume-measuring packing machine and inline capping machine, rotary capping machine and labeling machine, bottle unscrambler , screw capping machine ,tube filling and sealing machine, cartoning machine and other Packaging equipments.
So far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and our service as well as our integrity is acclaimed both in China and abroad. we will carry forward the spirit of "integrated innovation, and perseverance," discipline ourselves to be the first, and provide better and more perfect service for our new and old customers with enthusiasm and a new attitude.
Pharmaceutical Filler and Capper have been used by more and more companies in the industry, and many operators have learned how to use Pharmaceutical Filler and Capper, but they do not know much about its properties and working principle, so when Pharmaceutical Filler and Capper malfunctions, there is no way to start. So what is the working principle of Pharmaceutical Filler and Capper? Let's take a look at it.
This is the content list:
l Introduction of Pharmaceutical Filler and Capper
l Pharmaceutical Filler and Capper working principle
Introduction of Pharmaceutical Filler and Capper
Pharmaceutical Filler and Capper is a machine for filling and sealing objects, which is a small product in the packaging machine and is divided into the semi-automatic filling machine and fully automatic filling line in terms of the degree of automation of Pharmaceutical Filler and Capper production. From the point of view of packaging materials can be divided into liquid filling machinery, paste filling machine, powder filling machine, granule filling machine. Recently, with the QS certification of food, many manufacturers have started to focus on the quality and packaging of Pharmaceutical Filler and Capper.
Pharmaceutical Filler and Capper working principle
For Pharmaceutical Filler and Capper to achieve the linkage effect, it is driven by transmission machinery, so that all parts can work in coordination. When Pharmaceutical Filler and Capper reaches a certain number of bottles, there is a special infrared sensor on the inlet track to receive the induction, which automatically catches the bottles behind and allows the bottles in front to be filled. After the bottles are filled, then let the bottles behind enter to fill the space, to realize no bottle without filling. When the bottles enter the position under the filling head, the other working sections stop and only the filling headworks, when the bottles leave, the Pharmaceutical Filler and Capper's head stops working, the track section works and the bottle stopper is released. The clean bottles coming out of the bottle washer are fed into the inlet spiral of Pharmaceutical Filler and Capper by the bottle feeding belt and sent to the bottle-holding cylinder on the rotary table through the bottle feeding star wheel and raised, the bottle mouth is guided by the centering device and pressed against the lower part of the filling valve to form a seal. After being evacuated, the backpressure gas (CO,) in the storage cylinder is rushed into the bottle, when the gas pressure in the bottle is equal to the gas pressure in the storage cylinder, the liquid valve opens under the action of the liquid valve spring, at this time, the object is automatically filled into the glass bottle along the bottle wall through the guidance of the umbrella type reflective ring on the return tube and is replaced into the storage cylinder through the return tube, when the object rises to a certain height and closes the return tube mouth. Automatically stop down the object. Then the liquid valve and gas valve are closed to drain the pressure gas in the neck part of the bottle to prevent the gushing of the object with gas when the glass bottle is descending so that the whole filling process is completed This is the main working principle of Pharmaceutical Filler and Capper, and the users can use it according to these Users can know clearly which part of the machine has problems and repair them according to these features of Pharmaceutical Filler and Capper.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, constantly researching and developing packaging machinery for various materials such as liquid, powder, cream/oil, fluid, and semi-fluid. Extensive tests are conducted before the Pharmaceutical Filler and Capper leave the factory to ensure the quality of products and maintain the healthy development of the Pharmaceutical Filler and Capper market. If you are interested in Pharmaceutical Filler and Capper, you can contact us at www.cnzpack.com. You are very welcome and we look forward to working with you.