











After we purchase Pharmaceutical Filler and Capper, we need to install and debug Pharmaceutical Filler and Capper. Let's take a look at it together next.
This is the content list:
l Installation of Pharmaceutical Filler and Capper
l Commissioning of Pharmaceutical Filler and Capper
l Maintenance of Pharmaceutical Filler and Capper
Installation of Pharmaceutical Filler and Capper
According to different models and specifications of Pharmaceutical Filler and Capper, refer to the random manual for installation.
For small-sized Pharmaceutical Filler and Capper, it is not required to build the foundation, just install it on the flat workshop floor, make a good horizontal reference, adjust the elevation of incoming and outgoing chain belt according to the layout diagram, and adjust the legs to make the load of the whole machine evenly distributed.
For large-sized Pharmaceutical Filler and Capper, it is necessary to build a solid installation foundation as required. When installing, the horizontal benchmark should be played, especially when it is connected with the capping machine, the two parts of the incoming and outgoing bottle belts must be at the same horizontal benchmark.
To ensure the smooth bottle delivery of Pharmaceutical Filler and Capper, the inlet pallet under the inlet star wheel should be 0.5mm higher than the surface of the bottle tray, and the outlet pallet under the middle star wheel should be 0.5mm lower than the surface of the bottle tray. The running is free and there should be no jamming interference. The horizontal part of the liquid inlet pipe should have a certain slope to facilitate emptying and air discharge. Make sure the bearing load of Pharmaceutical Filler and Capper's legs is even. Matching equipment with the host, such as gas-liquid control box, vacuum pump system and electric control box, etc. are generally installed separately.
Commissioning of Pharmaceutical Filler and Capper
After confirming the installation of Pharmaceutical Filler and Capper is completed, the commissioning of Pharmaceutical Filler and Capper can be carried out step by step as follows. Replace suitable accessories according to the bottle type filled by Pharmaceutical Filler and Capper, and adjust the parts, including the inlet screw, guide bar spacing, side guard safety switch, star-shaped paddle wheel, reservoir, and capping head height adjustment, etc. Thoroughly clean the Pharmaceutical Filler and Capper reservoir, liquid piping, and gas piping to ensure that there is no foreign material. Make a hydraulic test on the storage tank and pipeline at the same time. Check carefully whether the wiring of the Pharmaceutical Filler and Capper control box is correct, and turn on the main switch only after the equipment is turned manually without jamming. Start the equipment in a pointing way to check if there is any abnormality. Start the Pharmaceutical Filler and Capper at low speed and check the starting, braking, emergency stop, and speed regulation performance. Then infuse an empty bottle at low speed, check whether it can pass through the bottle feed screw, guide bar, and star wheel smoothly and whether each control touch block can respond sensitively. Check whether the Pharmaceutical Filler and Capper can drop the cap smoothly and seal the cap tightly. After that, adjust the value of each instrument on the liquid and gas control cabinet according to the filing requirements of Pharmaceutical Filler and Capper. Check the liquid level and pressure of Pharmaceutical Filler and Capper reservoir, make filling test, adjust the filling head and control the bottling level.
Maintenance of Pharmaceutical Filler and Capper
Pharmaceutical Filler and Capper in the process of use, must be required to carry out regular maintenance. First of all, we must ensure that the lubrication status of the Pharmaceutical Filler and Capper must be good, and the lubrication points must be well-lubricated in time to maintain the oil level of each tank and the intact spray lubrication function. Timely replacement of a variety of damaged parts, such as seals, bottle transport parts, and transmission parts in the wearing parts. The movable parts that are not adjusted for a long time, such as the reservoir of Pharmaceutical Filler and Capper and the height adjustment device of the capping machine, should be run regularly to avoid rust and corrosion. Regularly and regularly clean the liquid tank of Pharmaceutical Filler and Capper, liquid delivery tube, filling valve, and parts that may contact with liquid as required. Liquid residue, oil, water, and glass fragments should be removed to keep the equipment neat and hygienic. Since there are many models and specifications of Pharmaceutical Filler and Capper, and the performance, structure, and working principle vary greatly, operators and maintenance personnel should use and maintain them according to the operation manuals accompanying each machine.
Our products are in great demand in both domestic and international markets, and we are committed to improving and developing to meet our customers and the market demand is our eternal theme and sincere commitment to our customers. If you are interested in Pharmaceutical Filler and Capper, you can contact us, our website is www.cnzpack.com.
Bottle Unscrambler is suitable for automatic unscramble of plastic round bottles, flat bottles, and tube-top bottles. Disordered bottles are poured into the bottle storage box. The bottles enter the filling machine conveyor line in an upright and orderly manner. The use of the Bottle Unscrambler equipment greatly reduces the labor intensity of the operators, and the equipment is stable and reliable with a high degree of automation. So, what is the structure of Bottle Unscrambler? Let's take a look together next.
This is the content list:
l The lifting mechanism of Bottle Unscrambler
l Bottle Unscrambler's unscrambler mechanism
l Bottle delivery mechanism of Bottle Unscrambler
l Bottle Unscrambler's bottle-out mechanism
The lifting mechanism of Bottle Unscrambler
Bottle Unscrambler has a stainless steel shell, stainless steel support feet, stainless steel large-capacity hopper, no bottle alarm and cap opening function, engineering plastic conveyor belt, which meets GMP requirements.
Bottle Unscrambler Bottle Unscrambler
Bottle Unscrambler adopts automatic quantitative feeding and turntable technology to maintain the dynamic balance of the number of bottles in the unscrambler tray to ensure stable and continuous bottle output. The Bottle Unscrambler enters the Bottle Unscrambler turntable by the lifting mechanism, and the turntable rotates at a high speed to sort out the bottles as required. Bottle Unscrambler web wheel removes irregular bottles.
Bottle delivery mechanism of Bottle Unscrambler
The bottle delivery mechanism of Bottle Unscrambler is a conveyor belt that meets GMP and FDA standards and requirements and uses flexible cushioning to facilitate bottle turnover. The structure of single-motor-driven double-belt pulleys ensures the same speed as the two clamping belts. The bottle-feeding mechanism of the Bottle Unscrambler clamps the bottles to the working surface of the conveyor through the conveyor belts on both sides. The bottle delivery mechanism of Bottle Unscrambler sorts out the bottles through different bottle flippers.
Bottle Unscrambler's bottle-out mechanism
The Bottle Unscrambler's single-motor drive double-pulley structure ensures that the two clamping belts have the same speed. Adjustable clamping belt speed. When the clamping belt sends out the bottle, the speed of the Bottle Unscrambler is the same as that of the main conveyor belt. The Bottle Unscrambler does not invert the bottle. The conveyor belt conforms to GMP and FDA standards and requirements. It adopts flexible buffering and is convenient. The bottle is turned over.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. So far, we have more than 100 domestic customers and more than 400 foreign customers. The quality of our Bottle Unscrambler and service as well as our integrity are widely praised at home and abroad. We will carry forward the spirit of "comprehensive innovation and perseverance", self-discipline and strive for the first place, and provide new and old customers with better and more complete services with enthusiasm and a new attitude. Bottle Unscrambler is in great demand in the domestic and foreign markets. Keep improving, develop to satisfy customers, and meet market needs are our eternal topic and our sincere commitment to customers. If you are interested in Bottle Unscrambler, you can contact us, our website is www.cnzpack.com. We look forward to your coming and hope to cooperate with you.
Liquid Filling Machine is specially designed for filling easy-to-open bottles. It has a reasonable design, simple structure, easy operation, and a mechanical bottle stop filling device. So what is the working principle of a Liquid Filling Machine? Let's take a look together next.
This is the content list:
l Transmission principle of Liquid Filling Machine
l The principle of the filling part of the Liquid Filling Machine
l Liquid Filling Machine's capping system
l The capping head of the Liquid Filling Machine
l The Liquid Filling Machine's tracking and filling mechanism
The Liquid Filling Machine transmits the power to the worm gear shaft of the reducer through the belt pulley, and then the worm gear shaft transmits the power to the paddlewheel shaft, the filling part, and the capping head through each gear. the filling part, the capping head, and each paddle wheel of the Liquid Filling Machine move synchronously, and the power is transmitted to the bottle feeding paddle wheel device through the bevel gear.
The liquid bottle of the Liquid Filling Machine is sent to the transition pulley by the large bottle inlet paddlewheel and then sent to the synchronous belt by the transition pulley. The bottle is dragged forward at a uniform speed by the inserts on the synchronous belt, and the filling needle of the Liquid Filling Machine is inserted into the bottle mouth under the control of the tracking mechanism and runs forward synchronously with the bottle to achieve tracking and filling. The diving needle rises with the liquid level to play the role of defoaming.
The cap supply system of the Liquid Filling Machine is composed of a cap delivery track, cap handling head, and cap-wearing mechanism. The lid management head adopts the principle of electromagnetic spiral oscillation to line up the messy lids and enter the lid delivery track through the reversing twist channel. When the Liquid Filling Machine passes through the lid-wearing mechanism, the bottle hangs on to the lid and passes through the pressure plate to make the lid wear correctly.
After the liquid bottle of Liquid Filling Machine enters the cap rolling head turntable with the cap on, the three rolling knives which have been opened will turn forward with the Liquid Filling Machine turntable with the bottle as the center and press the cap under the control of the cam, then the three rolling knives will roll towards the cap at the same time under the action of the cone sleeve, and after rolling, they will leave the cap at the same time and return to the original position.
The Liquid Filling Machine drives the gear and rack to move, thus driving the filling needle to do the reciprocating movement. By adjusting the relative position of the Liquid Filling Machine's syringe holder and mounting frame, the filling needle can be accurately inserted into the middle of the bottle opening.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, and so far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and services as well as our integrity are widely praised at home and abroad. We will carry forward the spirit of "comprehensive innovation, perseverance", self-discipline and strive for the first, with enthusiasm and a new attitude to provide more perfect service for new and old customers. If you are interested in Liquid Filling Machine, please contact us, our website is www.cnzpack.com
Bottle Unscrambler scientific maintenance and daily management institutionalization are very important. Scientific maintenance and the establishment of a daily management and use system have a very important role and significance for the actual use of mechanical products. It improves the standardization and performance of daily maintenance. It is more convenient for people to choose, especially it can be better suited to play the role of mechanical products in actual production. It is necessary to carry out reasonable maintenance and management of Bottle Unscrambler to improve the performance advantages of the product itself and let Bottle Unscrambler can help production in time during operation. So what are the precautions for Bottle Unscrambler? Let's take a look together next.
This is the content list:
l Things to do when installing Bottle Unscrambler
l Precautions when using Bottle Unscrambler
l Matters needing attention when cleaning the automatic Bottle Unscrambler
Things to do when installing Bottle Unscrambler
1. Before installing the Bottle Unscrambler, we need to check the Bottle Unscrambler thoroughly to see if the materials are complete and whether it is damaged. If you find a problem, please communicate with the manufacturer in time to solve it.
2. After checking the completion of the Bottle Unscrambler, follow the installation instructions to assemble the Bottle Unscrambler and adjust accordingly. Then add lubricating oil to the place that needs lubrication to ensure the flexibility of the Bottle Unscrambler.
3. After the test run Bottle Unscrambler, if it runs normally, it means that the installation of Bottle Unscrambler is completed.
Precautions when using Bottle Unscrambler
1. According to Bottle Unscrambler production conditions, choose to use a power supply that meets Bottle Unscrambler specifications.
2. To prevent electric shock, the Bottle Unscrambler must be well-grounded. Please equip the Bottle Unscrambler with a power socket with a ground wire.
3. After turning off the Bottle Unscrambler power switch, there is still strong voltage in some circuits in the electrical control of the machine. If the control circuit needs to be repaired, the power cord must be unplugged to avoid electric shock.
Matters needing attention when cleaning the automatic Bottle Unscrambler
1. If the company needs to disassemble and wash the Bottle Unscrambler, please do not turn off the air source and power supply.
2. Avoid electric shock to Bottle Unscrambler. When disassembling the Bottle Unscrambler, do not directly rinse the body with water, because the Bottle Unscrambler is equipped with electrical control components. If the components contact the water source, there is a risk of electric shock and may damage the Bottle Unscrambler components.
3. It is strictly forbidden to show the residues of the filled items on the Bottle Unscrambler, such as oil stains, paints, etc. The existence of these things will accelerate the corrosion of the Bottle Unscrambler and affect its service life. If any residual items are found, they should be cleaned up in time.
4. Lubricate the Bottle Unscrambler regularly, clean the Bottle Unscrambler every once in a while, and make a cleaning record for later review.
We have obtained ISO9001 quality management system certification, and some products have passed CE certification. The production of Bottle Unscrambler is strictly controlled. If you are interested in Bottle Unscrambler, you can contact us. Our website is www.cnzpack.com.
Capping Machine operation, accuracy error, installation adjustment, equipment cleaning, maintenance, and other aspects are very simple and convenient. Capping Machine has been widely used in various industries such as daily chemical and grease, and can fill different high-viscosity fluids. So what are the working principles and structural characteristics of the Capping Machine? Let's take a look together next.
This is the content list:
l How Capping Machine works
l Structural characteristics of Capping Machine
How Capping Machine works
The Capping Machine adopts a new horizontal design, which is light and convenient and can automatically pump the material. For thicker slurry, a hopper can be added. When the Capping Machine is in the "auto" state, the Capping Machine will automatically perform continuous filling at a set speed. Capping Machines can be divided into three types: atmospheric filling machine, vacuum filling machine, and pressure filling machine.
Under normal pressure, Capping Machine can fill the liquid in a self-flowing manner according to the weight of the liquid itself. The filling method is to fill at a pressure greater than atmospheric pressure. The pressure in the liquid storage tank is greater than the pressure in the bottle, and the liquid that needs to be filled will enter the bottle depending on the pressure difference. The key component of the Capping Machine is the PLC operation control system. Under normal pressure, Capping Machine can fill the liquid in a self-flowing manner according to the weight of the liquid itself. The filling method is to fill at a pressure greater than atmospheric pressure. The pressure in the liquid storage tank is greater than the pressure in the bottle, and the liquid that needs to be filled will enter the bottle depending on the pressure difference. The key component of the Capping Machine is the PLC operation control system.
The principle of the Capping Machine is relatively easy to understand. The improved control system simplifies the structure of the machine. It can be seen from the operating conditions and control efficacy tests of the actual application that the automation level of the system has reached the design requirements. This reduces the labor intensity of the operator and makes the production line that needs filling production about 30% higher than before, so the probability of failure of the Capping Machine is significantly reduced.
Structural characteristics of Capping Machine
The design of the Capping Machine is very reasonable and appropriate, the remainder of the machine is very small, and the operation and use are very simple. The pneumatic parts inside the Capping Machine all use new pneumatic components. The piston and cylinder of the Capping Machine cylinder are made of polytetrafluoroethylene and stainless steel to meet the requirements of GMP testing. The filling quantity and filling speed of the Capping Machine can be adjusted at will, and the degree is relatively high.
The Capping Machine can be modified according to actual production needs. It can be transformed into a multi-head system, explosion-proof system, and overflow system. The Capping Machine is suitable for use in food, daily necessities, pesticides, and other industries, and has a broad application prospect.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. The company strictly controls the quality of the Capping Machine. If you are interested in Capping Machine, you can contact us, our website is www.cnzpack.com. I look forward to your coming and hope to cooperate with you.
The tube Filling machine And the Sealing machine are determined by multiple parameters. It is impossible to describe a Tube Filling machine And Sealing machine with any single parameter. Shaft power, blade displacement, pressure head, blade diameter, and filling speed are the five basic parameters that describe a Tube Filling Machine And Sealing machine. So, let's take a look at the principle of the Tube Filling machine And Sealing machine together. Here are some answers.
Here is the content list:
l Basic parameters.
l The shear rate of the fluid.
l Small slot and big slot.
Basic parameters.
The displacement of the blade is proportional to the flow rate of the blade itself, the first power of the blade speed, and the third power of the blade diameter. The shaft power consumed by the filling is proportional to the specific gravity of the fluid, the power standard of the blade itself, the third power of the speed, and the fifth power of the blade diameter. In the case of a certain power and blade form, the blade displacement and pressure head can be adjusted by changing the diameter of the blade and the matching of the speed. That is, the large diameter blade is equipped with a low-speed Tube Filling machine And a Sealing machine. High flow effect and low-pressure head, while the small diameter blade with high speed produces a higher pressure head and lower flow effect.
The shear rate of the fluid.
In the filling tank, the only way to make the micelles collide with each other is to provide a sufficient shear rate. According to the mechanism of the Tube Filling Machine And Sealing machine, it is because of the existence of fluid velocity difference that the fluid layers are mixed. Therefore, where the filling process always involves the fluid shear rate lhhaha620. Shear stress is a force that is the real cause of bubble dispersion and droplet breaking in filling applications. It must be pointed out that the shear rate at each point of the fluid in the entire stirred tank is not the same.
Small slot and big slot.
Experimental research shows that, as far as the blade area is concerned, no matter what type of blade, when the diameter of the blade is constant, the maximum shear rate and the average shear rate increase with the increase of the speed. However, when the rotation speed is constant, the relationship between the maximum shear rate and the average shear rate, and the diameter of the blade is related to the slurry type. When the rotation speed is constant, the maximum shear rate of the radial blade increases with the increase of the blade diameter, and the average shear rate has nothing to do with the diameter of the blade. These concepts about the shear rate of the blade area require special care in the design of the Tube Filling Machine And Sealing machine to reduce and enlarge. Because the small groove is compared with the large groove, the small groove Tube Filling Machine and Sealing machine often has the characteristics of high speed, small blade diameter, and low tip speed. The large groove Tube Filling Machine And Sealing machine often has the characteristics of low speed, large blade diameter, and high tip speed.
Our official website is https:// www.cnzpack.com/. If you are engaged in work related to the Tube Filling machine And Sealing machine, you can communicate with us on the website.
In our production and life, the Liquid Filling Machine has a significant impact on many industries, so what is the method of using the Liquid Filling Machine? Let's go take a look next.
This is the content list:
l The ground wire must be well-grounded before the Liquid Filling Machine works
l Liquid Filling Machine liquid filling system assembly
The ground wire must be well-grounded before the Liquid Filling Machine works.
The ground wire must be well-grounded before the Liquid Filling Machine works, and then the appropriate standard syringe must be selected according to the different filling volumes. Generally, a 1ml syringe is used when the dispensing range is 0.2-1ml. Use a 5ml syringe for 1-5ml.use a 10ml syringe for 5-10ml. The 20ml model uses a 20ml glass infusion device. The 100ml model uses a 100ml glass infusion device, and the 500ml model uses the stainless steel filling system produced by our factory.
Liquid Filling Machine liquid filling system assembly
Pull out the inner core of the Liquid Filling Machine syringe, put the screw sleeve on the inner core of the syringe, and use the screw sleeve to properly fasten it to the lower base (cleanliness must be paid when disassembling the syringe). Place the upper clamp seat on the outlet end of the Liquid Filling Machine syringe jacket, and properly tighten the nuts on both sides to assemble the inner core and outer jacket of the installed Liquid Filling Machine syringe into one body. At this point, the Liquid Filling Machine injection system is assembled.
Place the Liquid Filling Machine valve with the arrow facing upwards and the arrow mark facing outwards and fix it on the fixing screw with a nut. Assemble the Liquid Filling Machine with a complete liquid filling system, align the upper and lower round holes of the liquid filling system components with the upper and lower fixing rods respectively, and put them on the bearing so that the outer end surface and the bearing surface are levels. When assembling the lower end, do not make the screw sleeve and the crank touch to prevent abnormal noise when the crank on the Liquid Filling Machine rotates (the screw sleeve and the crank are about 1mm apart when installed correctly). After the liquid filling system is installed correctly, tighten it. Tighten the screws up and down. Use a short hose to connect the Liquid Filling Machine syringe to the valve connection nozzle. The liquid inlet pipe is connected to the water inlet, and the liquid outlet pipe is connected to the water outlet. To prevent the liquid inlet and outlet pipes from being entangled, clip the liquid inlet and outlet pipes into the ear openings on the side of the casing.
Turn the crank of the Liquid Filling Machine by hand, it should be able to rotate freely, otherwise, the assembly is wrong, you should check whether the Liquid Filling Machine injection system is fastened to the rotating bearing.
Our company has obtained more than 20 invention patents and utility model patents. The main products are a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and online capping machine, capping machine and labeling machine, bottle unscrambler, tube filling and sealing machine, Cartoning machines, and other packaging equipment. If you are interested in Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.
Korea East Asia Pharmaceutical Company, ordered a syrup filling line from our company, from bottle management - bottle washing - filling - corking - capping - labeling, the whole line in the Korean factory to complete the commissioning task, the whole line production design speed of 120 bottles per minute high-speed filling line.