











In our production and life, the Liquid Filling Machine has a significant impact on many industries, so what is the method of using the Liquid Filling Machine? Let's go take a look next.
This is the content list:
l The ground wire must be well-grounded before the Liquid Filling Machine works
l Liquid Filling Machine liquid filling system assembly
The ground wire must be well-grounded before the Liquid Filling Machine works.
The ground wire must be well-grounded before the Liquid Filling Machine works, and then the appropriate standard syringe must be selected according to the different filling volumes. Generally, a 1ml syringe is used when the dispensing range is 0.2-1ml. Use a 5ml syringe for 1-5ml.use a 10ml syringe for 5-10ml. The 20ml model uses a 20ml glass infusion device. The 100ml model uses a 100ml glass infusion device, and the 500ml model uses the stainless steel filling system produced by our factory.
Liquid Filling Machine liquid filling system assembly
Pull out the inner core of the Liquid Filling Machine syringe, put the screw sleeve on the inner core of the syringe, and use the screw sleeve to properly fasten it to the lower base (cleanliness must be paid when disassembling the syringe). Place the upper clamp seat on the outlet end of the Liquid Filling Machine syringe jacket, and properly tighten the nuts on both sides to assemble the inner core and outer jacket of the installed Liquid Filling Machine syringe into one body. At this point, the Liquid Filling Machine injection system is assembled.
Place the Liquid Filling Machine valve with the arrow facing upwards and the arrow mark facing outwards and fix it on the fixing screw with a nut. Assemble the Liquid Filling Machine with a complete liquid filling system, align the upper and lower round holes of the liquid filling system components with the upper and lower fixing rods respectively, and put them on the bearing so that the outer end surface and the bearing surface are levels. When assembling the lower end, do not make the screw sleeve and the crank touch to prevent abnormal noise when the crank on the Liquid Filling Machine rotates (the screw sleeve and the crank are about 1mm apart when installed correctly). After the liquid filling system is installed correctly, tighten it. Tighten the screws up and down. Use a short hose to connect the Liquid Filling Machine syringe to the valve connection nozzle. The liquid inlet pipe is connected to the water inlet, and the liquid outlet pipe is connected to the water outlet. To prevent the liquid inlet and outlet pipes from being entangled, clip the liquid inlet and outlet pipes into the ear openings on the side of the casing.
Turn the crank of the Liquid Filling Machine by hand, it should be able to rotate freely, otherwise, the assembly is wrong, you should check whether the Liquid Filling Machine injection system is fastened to the rotating bearing.
Our company has obtained more than 20 invention patents and utility model patents. The main products are a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and online capping machine, capping machine and labeling machine, bottle unscrambler, tube filling and sealing machine, Cartoning machines, and other packaging equipment. If you are interested in Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.
In our production and life, the Cartoning Machine is of great significance to us, but sometimes, the Cartoning Machine will fail, so what is the reason for the failure of the Cartoning Machine? Next, let us analyze it together.
This is the content list:
Stop or stop between conveyor belts
The carton cannot be sucked down
The carton is not formed or ejected at the mouth of the box feeding template after being sucked
Can't suck the instructions
The paper rebounds during the suction process of the manual
The manual does not fold well
Uneven folding of the manual
There are curls and creases after the manual is folded
Manual stuck in the fence
1. Cartoning Machine shuts down at intervals to check if there is a shortage of materials and automatically starts up when supplemented.
2. Shut down the Cartoning Machine to check whether the power supply including the power supply part, the motor, or the governor is normal.
1. Whether the cartons of Cartons Machine are arranged neatly.
2. Whether the cartons of the Cartoning Machine are pasted together.
3. Whether the air pressure of the Cartoning Machine suction head is normal.
1. Check if the cartons of Cartons Machine are too hard.
2. Check whether the position of the guide rod of the cartons placed by the Cartoning Machine and the box delivery template are not correct.
3. Check whether the small hook spring at the rear of the Cartoning Machine delivery template is deformed.
4. Check if the height of the suction head of the Cartoning Machine and the box delivery track is correct.
1. Whether the Cartoning Machine manual is deformed, causing the suction head to fail to suck.
2. Whether the suction head gas of the Cartoning Machine is parallel to the manual.
3. Whether the paper width of the Cartoning Machine manual is different, the error must be within 1mm. The stacking position of the manual should be adjusted to a difference of 0.5mm from the inner edge when the suction head rises to the high position.
4. The small paper-separating hook above the suction head of the Cartoning Machine origami moves too early. Generally, the small hook should be inserted into the gap between the paper and the paper before the suction head is about to drop. The height of the small hook is adjusted to be 0.5mm away from the suction head when it is in the high position.
1. The foot-lifting action of the Cartoning Machine's manual was too early, and the manual was taken away by the foot support before being pulled down. The position of the feet of the Cartoning Machine is so that it does not touch the sucked manual when it is returned and it returns to the high position when the paper picking notch wheel has not pulled the paper.
2. Whether the matching speed of the Cartoning Machine suction head and paper picking wheel is the same. The suction head of the Cartoning Machine should be lowered first, and then the front part of the paper picking notch wheel should be pressed onto the paper.
1. Check if the Cartoning Machine paper is deformed and bent, and if there are burrs.
2. Is there any foreign matter in the fence of the Cartoning Machine blocking the paper?
3. The gap between the opening of the Cartoning Machine fence and the folding stick is too large, causing the paper to come out.
4. Is the gap between Cartons Machine's folding sticks too large to hold the paper? Adjust the adjusting screws at both ends of the folding stick to reduce the gap. If the Cartoning Machine folding stick has been used for too long and worn out, the folding stick must be replaced.
Check the Cartoning Machine to adjust the front and rear positions of the barriers in the fence to achieve the required folding size.
1. Is the gap between the Cartoning Machine baffle and the folding stick too large? Adjust the middle position of the baffle and folding stick.
2. If the middle position of the Cartoning Machine baffle and the folding stick has been adjusted, and there is still a large gap, remove the positioning pins on the Cartoning Machine baffle and re-adjust until the gap does not feed paper.
1. Whether the paper feeding gap of Cartoning Machine folding stick is too large and paper feeding is weak. The adjustment method is the same as above.
2. The installation position of the lower half of the Cartoning Machine fence is too long than the arc guide plate on it so that the paper cannot enter the folding stick below. Loosen all the fixing screws on the Cartoning Machine fence and adjust the board backward, but it should not be shorter than the upper guide plate and should be 1-3 mm longer than the guide plate. If it is shorter than the guide plate, the Cartoning Machine manual may go directly into the folding stick below without folding.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It will conduct a large number of tests before the Cartoning Machine leaves the factory to reduce the failure of the Cartoning Machine and provide warranty services. If you are interested in the Cartoning Machine, you can contact us Contact, our website is www.cnzpack.com.
The Cosmetic Filling machine And Capping machine has a wide range of applications, not only in the cosmetics industry but also in food, daily chemical, pharmaceutical, and other industries. It is very flexible to use, can be adapted to different bottle mouths, and the operation is relatively simple and quick. Because of its unique advantages, it has won unanimous praise from customers. Next, let's take a look at the advantages, characteristics, and manufacturer introduction of Cosmetic Filling machines And Capping Machines. Here are some answers.
Here is the content list:
l Advantages of Cosmetic Filling machine And Capping machine.
l The performance characteristics of Cosmetic Filling machine And Capping machine.
l Introduction of Cosmetic Filling machine And Capping machine manufacturer.
Advantages of Cosmetic Filling machine And Capping machine.
Cosmetic Filling Machine And Capping machine integrates mechanical, pneumatic, and automatic. The characteristics of a high degree of automation, high output, wide application, and good stability make this machine more popular. The Cosmetic Filling machine And Capping machine can automatically unscramble bottles, fill, seal, cap, and label. Equipped with an automatic internal plug-in row and external cover plug test, it can realize no internal plug and non-external plug and eliminate the non-external plug. The labeling adopts a belt rolling structure, a fast-rolling structure, and an 8-dimensional angle adjustment label to realize the labeling of two symmetrical labels or high-precision labeling.
The performance characteristics of Cosmetic Filling machine And Capping machine.
First, the man-machine interface setting, intuitive and convenient operation, PLC control, accurate loading. Frequency conversion control, arbitrary adjustment of production speed, automatic counting. Second, the Cosmetic Filling machine And Capping machine is made of stainless steel, which meets GMP requirements. Third, the equipment fully complies with GMP requirements. Microcomputer setting, accurate filling volume, convenient operation, automatic shutdown function, automatic shutdown for any track with continuous no filling and no internal clogging. Fourth, the Cosmetic Filling machine And Capping machine is easy to operate and easy to maintain.
Introduction of Cosmetic Filling machine And Capping machine manufacturer.
Wenzhou Zungwan Intelligent Machine Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream, ointment, fluid, and semi-fluid materials. We have obtained ISO9001 quality management system certification, and some products have passed CE certification. Our company has obtained more than 20 invention patents and utility model patents. The quality of our Cosmetic Filling Machine And Capping machine and service as well as our integrity are widely praised at home and abroad.
The first-class quality of Cosmetic Filling machine And Capping machine and efficient and fast after-sales service have created the excellent products of "Zhonghuan". Cosmetic Filling Machine And Capping machine is in great demand in domestic and foreign markets. Keep improving, develop to satisfy customers, and satisfy market demands are our eternal topic and our sincere commitment to customers.
Our official website is https:// www.cnzpack.com/. If you are engaged in work related to Cosmetic Filling machines And Capping machines or want to learn more about our company, you can communicate with us on the website. We wholeheartedly provide users with better products and services!
With the increasingly fierce competition in the manufacturing and production of plastic bottles in the food and pharmaceutical industries, Bottle Unscrambler has become more and more solid backing for the food and pharmaceutical plastic bottle markets. So how does it play a role? We will introduce the work process and personnel operation specifications of Bottle Unscrambler. Let's take a look together next.
This is the content list:
The workflow of Bottle Unscrambler
Personnel operation specification of Bottle Unscrambler
The workflow of Bottle Unscrambler is generally as follows: manually put materials into the storage bottle library, the materials in the storage bottle library will be automatically quantified and fed to the turntable at the set speed. The turntable rotates at a high speed to supply the bottles as required, the web wheel The irregular bottles are removed, and the bottle dividing part sends the bottles from the turntable to the bottle unscramble part at a certain speed. The Bottle Unscrambler part of the Bottle Unscrambler clamps the bottles to the working surface of the conveyor through the conveyor belts on both sides, and at the same time sorts the bottles through the bottle turner. The Bottle Unscrambler electronic control system performs real-time monitoring and feedback through the sensors of each part to achieve fully automated operation requirements, and save a lot of labor costs and avoid losses caused by human error factors.
To ensure the normal and safe operation of Bottle Unscrambler, there are special operating procedures established for it. Operators and equipment management personnel shall perform standardized operations of Bottle Unscrambler under these procedures. This safe operation specification is commonly used in Bottle Unscramblers, mixers, high-speed automatic Bottle Unscramblers, etc.
1. First check the Bottle Unscrambler's intact, clean, and expiration status identification and the equipment operation record of the shift. If the inspection finds that the Bottle Unscrambler has exceeded the cleaning validity period, it is necessary to further clean the equipment according to the equipment cleaning operation rules and fill in the equipment status identification.
2. Check the Bottle Unscrambler and the Bottle Unscrambler to confirm that there is no foreign matter, and turn the bottle plate and unscrambler to confirm that it can work normally.
3. Turn on the Bottle Unscrambler power switch, check the touch screen and three photoelectric switches. If both are energized, the lack of a bottle alarm will be displayed on the touch screen. When the electric eye is blocked by hand, the screen displays the blocking alarm, and the two photoelectric switches are in a normal state.
4. Turn on the Bottle Unscrambler compressed air, use the bottom of the bottle to shake under the electric eye of the bottle puller, compressed air will be sprayed out, and the equipment can be turned on normally.
To ensure that the various parts of the Bottle Unscrambler can work normally, the formal operation can be divided into five steps: click the host start and lift start on the touch screen respectively, and observe whether the Bottle Unscrambler has abnormal noise when it is running. After powering on the Bottle Unscrambler and confirming that there is no abnormal condition, stop the device, but the qualified infusion bottle upright in the bottle feeding bracket, and start the device again. The bottle will pass through the rotating carousel of the device and enter the conveyor belt to start the bottle unscramble operation. Run at low speed when starting up, and then adjust the lifting speed and unscramble speed according to the actual production, so that the speed of the Bottle Unscrambler equipment can match the actual production speed. To prevent such phenomena from happening. If such a phenomenon occurs, stop the machine immediately to eliminate the fault before it can continue to run. During the operation of the equipment, the bottles should be put in continuously, and observe whether there are phenomena such as pouring, jamming, broken bottles, etc. If any, stop the machine immediately and start the production after troubleshooting. After the production is over, stop the equipment, turn off the power of the Bottle Unscrambler, and clear the remaining materials out of the equipment.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. When the Liquid Filling Machine leaves the factory, it will provide customers with detailed Liquid Filling Machine operation procedures and operating specifications. If you are interested in Liquid Filling Machine, you can contact us, our website is www.cnzpack.com.
Tube Filling machine And Sealing machine adopt the latest module circuit, stable working performance, high efficiency, and all components adopt famous brand products. Under the careful design of our company, various advanced Tube Filling Machine And Sealing machines have been produced. Mainly used for sealing toothpaste, cosmetics, medicine, food, industrial products, and various hoses. Next, let's take a look at the cleaning and maintenance of the Tube Filling machine And Sealing machine. Here are some answers.
Here is the content list:
Tube Filling machine And Sealing machine cleaning.
Daily maintenance of Tube Filling machine And Sealing machine.
First, regularly clean the surface of the Tube Filling machine And Sealing machine, the bottom plate and the lower mold slide plate, grooves, the upper mold inner pressure plate, and the positioning rod. Second, grease should be added to the transmission parts of the lower mold slide plate, pressing rod bearing, eccentric wheel and guidepost, guide rail, and so on regularly to ensure the performance of the Tube Filling Machine And Sealing machine. Third, the method of cleaning the toothed knife: first plug the two drain holes of the lower mold with a cotton ball, pour boiling water into the groove of the lower mold, until it is full, then push the slide of the lower mold into place, and lower the upper mold. Press to the lowest point, let the toothed knife soak for a few minutes until it is clean, repeat several times.
First, check the equipment ground wire frequently to ensure reliable contact; clean the weighing platform frequently; check whether the pneumatic pipeline is leaking and whether the air pipe is broken. Second, change the lubricating oil of the reducer motor every year, check the tightness of the chain, and adjust the tension in time. Third, the sensor of the Tube Filling Machine And Sealing machine is a high-precision, high-sealing, and high-sensitivity device. Impact and overload are strictly prohibited, and no contact is allowed during the working process, and it is not allowed to be disassembled if it is not required for maintenance. Fourth, if it is not used for a long time, empty the material in the pipeline. Fifth, observe the moisture filter and oil mist device of the pneumatic combination two-piece before going to work every day. Sixth, during the production, we should always patrol and observe the mechanical parts to see if the rotation and lifting are normal if there is any abnormality, and if the screws are loose. Seventh, do a good job of cleaning and sanitation, keep the surface of the Tube Filling machine And Sealing machine clean, often remove the accumulation on the scale body, and pay attention to keeping the electric control cabinet clean.
Wenzhou Zungwan Intelligent Machine Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream, ointment, fluid, and semi-fluid materials. If you are engaged in work related to Tube Filling machine And Sealing machine or want to know more about our company, you can contact us. Our official website is https:// www.cnzpack.com/.
We know that Labeling Machine brings great convenience to our production and life, so what are the working principles and performance characteristics of Labeling Machine? Let's go take a look next.
This is the content list:
l How the Labeling Machine works
l Performance characteristics of Labeling Machine
How the Labeling Machine works
First of all, the working principle of the Labeling Machine is to put the roll of labels in place, and then put the round bottle on the conveyor belt. The labeling head of the Labeling Machine is set at a fixed distance. The labeling wheel and the rotating shaft are used to move the label. Separate from the base film, it should be noted that the Labeling Machine label tape needs to be kept in a constant state during this operation.
Then, the Labeling Machine conveyor belt pushes the round bottle. When it is transferred to the area, the driving wheel will slow down and stop applying the label to the bottle. The Labeling Machine logo can be applied to the entire bottle or half of the bottle. The basic working principle is the same.
The above is the working principle of the Labeling Machine. At present, Labeling Machine has been widely used in the market, gradually replacing manual labeling, and the labeling speed of the prototype Labeling Machine is much higher than that of manual operation, and the accuracy is also higher. The cost of manual operation is lower than that of manual operation. Therefore, the circular Labeling Machine is more demanded by consumers.
Performance characteristics of Labeling Machine
1. The Labeling Machine is equipped with a double-labeling mechanism. Labeling Machine to ensure the accuracy of labeling, Labeling Machine double extrusion labeling can effectively eliminate air bubbles, to ensure that the label head and tail are tightly attached.
2. Labeling Machine intelligent control, automatic photoelectric tracking, Labeling Machine with no labeling, no label automatic correction and automatic detection of the label function, Labeling Machine to avoid wasting labels and missing labels.
3. Labeling Machine with elastic pressure top mechanism to ensure stable product delivery, Labeling Machine effectively eliminates the inherent error of the bottle height.
4. The Labeling Machine is equipped with an automatic bottle splitting mechanism, which automatically separates the spacing before the bottle guide, Labeling Machine to ensure the stability of the subsequent bottle guide, conveying, and labeling.
5. The Labeling Machine adopts a double-sided hard plastic synchronous guide chain to automatically ensure the neutrality of the bottle.
6. Labeling Machine has little requirement for workers to put bottles and assembly line to receive bottles, which greatly reduces the difficulty of workers' work or assembly line docking. Labeling Machines can be produced on a single machine or connected with assembly-line production.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It strictly controls the production of Labeling Machines and uses the working principle and performance characteristics of Labeling Machines to produce Labeling Machines that are more in line with consumer needs. If you are interested in Labeling Machines, you can contact us, our website is www.cnzpack.com.
They ordered two hand sanitizer filling lines, requiring a speed of 150 bottles per minute, from automatic bottle management - automatic filling - automatic cap management - automatic capping - automatic labeling.
The whole production line was designed, developed and produced by our company, and it took 70 days from the finalization of the contract to delivery. Because of the outbreak of New Crown epidemic in the U.S., we completed the delivery of the equipment ahead of schedule and flew it to the U.S.
Now Bag Packing Machine is the most popular packaging equipment in the market, and it is used in all walks of life. Now the ubiquitous refractory materials, coffee, salt, MSG, potato chips, etc. are packed in a variety of packaging, then What are the general characteristics of a Bag Packing Machine? Let's take a look together next.
This is the content list:
l Standardization and modularization of Bag Packing Machine structure design
l Bag Packing Machine packaging speed increases
l High-precision structure movement of Bag Packing Machine
l Bag Packing Machine control is intelligent and flexible
Standardization and modularization of Bag Packing Machine structure design
When using a Bag Packing Machine to complete the packaging of different materials, the modular design of the original model can be used to quickly change the specifications or convert to other packaging models in a short time. The Bag Packing Machine is not the metering system that provides enough space.
Bag Packing Machine packaging speed increases
At present, the single-line packaging speed of the small Bag Packing Machine is generally 30-120 bags/min. Compared with the manual, the packaging speed is greatly accelerated. The Bag Packing Machine is more helpful for enterprises to realize automatic packaging and save time and cost.
High-precision structure movement of Bag Packing Machine
Because Bag Packing Machine adopts various new technologies, such as high-precision mechanical control of various actions through servo motors, encoders and digital control (NC), power load control PLC, etc., the filling and metering accuracy of the Bag Packing Machine is reduced. The bag-making accuracy has been improved.
Bag Packing Machine control is intelligent and flexible
Most Bag Packing Machines track and adjust various mechanical parameters through intelligent control instruments and menu-type software on the touch screen. The Bag Packing Machine electronic display shows the length of the bag, the packing speed, the net content of the filling and the packing output, etc., which can be understood at a glance. The standard color code tracking photoelectric system can ensure the correct printing patterns of the packaged products. In addition, Bag Packing Machine can perform online status monitoring and fault diagnosis analysis of the working process. Once a problem occurs, Bag Packing Machine will automatically stop and display the cause and solution of the fault.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. The quality of our machines and services as well as our integrity are widely praised at home and abroad. We will carry forward the spirit of "comprehensive innovation and perseverance", self-discipline and strive for the first place, and provide new and old customers with better and more complete services with enthusiasm and a new attitude. The production of the Bag Packing Machine is strictly controlled. The company uses the characteristics of the Bag Packing Machine to improve it to meet the needs of consumers. If you are interested in Bag Packing Machine, you can contact us. Our website is www.cnzpack.com. We look forward to your coming and very much hope to cooperate with you.