Intellectual High Viscosity Filling Machine factory- Manufacturers Suppliers Factory From China

After the Labeling machine sensor sends a signal that the labeling object is ready to be labeled, the drive wheel on the Labeling machine turns up. As the rolled label is in a tight state on the equipment, when the Labeling machine backing paper is tightly attached to the peeling plate and changes direction, the Labeling machine label is forced to disengage due to the rigidity of its material and is ready to be labeled. At this time, the labeling object is located just below the label, under the action of the labeling wheel, to achieve synchronous labeling. After the Labeling machine has finished labeling, the sensor under the roll label sends a stop signal, the drive wheel comes to a standstill, and a labeling cycle end. No matter which type of Labeling machine, the labeling process is roughly the same. The difference is that the installation position of the Labeling machine is different, the labeling object is conveyed differently and positioned differently, and the form of the labeling roller of the Labeling machine is also different. So, what are the Labeling machine's requirements for labels? Let's look at it together next.

This is the content list:

l Surface material

l Release force

l At the end of the paper

l Processing quality

Surface material

Labeling machine label stiffness is the key to labeling, so the Labeling machine surface material is required to have a certain strength and hardness. Labeling machine label stiffness and the thickness of the material and the area of the label, so the Labeling machine in the use of soft film material should be appropriate to increase its thickness, generally controlled at 100μm or more. Labeling machine thin paper materials, such as 60 ~ 70g/m2 labeling paper, are generally not suitable for the production of large labels, but suitable for processing into small labels, such as price tags used on the price tag. Labeling machine label stiffness is not good, it will cause labeling out of the label, or label and backing paper reward so that the automatic labeling failure.

Peel-off force

Labeling machine peel-off force is the force at which the label is separated from the backing paper by the Labeling machine. The Labeling machine release force is related to the type and thickness of the adhesive, the silicone coating on the surface of the backing paper, and the ambient temperature at the time of labeling. If the Labeling machine release force is too small, the label will easily fall off (leave the backing paper) during the conveying process. The Labeling machine's release force is too large, the label will be difficult to detach from the backing paper, and it will not be able to produce labels. The Labeling machine should be integrated control of the technical indicators so that the release force is maintained within a reasonable range.

At the end of the paper

Is also an important indicator to control automatic labeling. The requirements of the Labeling machine base paper surface silicon-coated evenly, the Labeling machine peeling force is consistent. Uniform thickness and good tensile strength ensure that the Labeling machine will not break when labeling. Uniform thickness and good light transmission of the Labeling machine ensure that the sensor can correctly identify the location of the label.

Processing quality

Requires that both sides of the Labeling machine backing paper after slitting should be flat and free of fracture to avoid the backing paper from breaking when the tension changes. Labeling machine die-cutting, to avoid cutting through the backing paper or damage to the silicone layer. If the Labeling machine backing paper and silicone coated layer are destroyed, the Labeling machine backing paper will break easily or the glue in the label will penetrate the backing paper. In addition, the static electricity in the web label must be eliminated before Labeling machine labeling, because static electricity will lead to Labeling machine labeling failure or labeling inaccuracy.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. Before the Labeling machine leaves the factory, it will conduct a large number of tests on the Labeling machine to maintain the healthy development of the Labeling machine market. If you are interested in the Labeling machine, you can contact us, our website is www.cnzpack.com.

Wenzhou Zungwan Intelligent Machine Co.,Ltd. is the professional equipment manufacturer to keep researching and developing the packing machinery for every type of liquid, powder, cream/ointment, fluid and half-fluid etc. materials. We have Obtained ISO9001 quality management system authentication and parts of our products have passed CE authentication. Our company has obtained more than 20 invention patents and utility model patents. The main products range from nail polish filling machine, perfume machine,perfume filling machine, powder serial automatically volume-measuring packing machine and inline capping machine, rotary capping machine and labeling machine, bottle unscrambler , screw capping machine ,tube filling and sealing machine, cartoning machine and other Packaging equipments.

So far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and our service as well as our integrity is acclaimed both in China and abroad. we will carry forward the spirit of "integrated innovation, and perseverance," discipline ourselves to be the first, and provide better and more perfect service for our new and old customers with enthusiasm and a new attitude.

Capping Machine operation, accuracy error, installation adjustment, equipment cleaning, maintenance, and other aspects are very simple and convenient. Capping Machine has been widely used in various industries such as daily chemical and grease, and can fill different high-viscosity fluids. So what are the working principles and structural characteristics of the Capping Machine? Let's take a look together next.

This is the content list:

l How Capping Machine works

l Structural characteristics of Capping Machine

How Capping Machine works

The Capping Machine adopts a new horizontal design, which is light and convenient and can automatically pump the material. For thicker slurry, a hopper can be added. When the Capping Machine is in the "auto" state, the Capping Machine will automatically perform continuous filling at a set speed. Capping Machines can be divided into three types: atmospheric filling machine, vacuum filling machine, and pressure filling machine.

Under normal pressure, Capping Machine can fill the liquid in a self-flowing manner according to the weight of the liquid itself. The filling method is to fill at a pressure greater than atmospheric pressure. The pressure in the liquid storage tank is greater than the pressure in the bottle, and the liquid that needs to be filled will enter the bottle depending on the pressure difference. The key component of the Capping Machine is the PLC operation control system. Under normal pressure, Capping Machine can fill the liquid in a self-flowing manner according to the weight of the liquid itself. The filling method is to fill at a pressure greater than atmospheric pressure. The pressure in the liquid storage tank is greater than the pressure in the bottle, and the liquid that needs to be filled will enter the bottle depending on the pressure difference. The key component of the Capping Machine is the PLC operation control system.

The principle of the Capping Machine is relatively easy to understand. The improved control system simplifies the structure of the machine. It can be seen from the operating conditions and control efficacy tests of the actual application that the automation level of the system has reached the design requirements. This reduces the labor intensity of the operator and makes the production line that needs filling production about 30% higher than before, so the probability of failure of the Capping Machine is significantly reduced.

Structural characteristics of Capping Machine

The design of the Capping Machine is very reasonable and appropriate, the remainder of the machine is very small, and the operation and use are very simple. The pneumatic parts inside the Capping Machine all use new pneumatic components. The piston and cylinder of the Capping Machine cylinder are made of polytetrafluoroethylene and stainless steel to meet the requirements of GMP testing. The filling quantity and filling speed of the Capping Machine can be adjusted at will, and the degree is relatively high.

The Capping Machine can be modified according to actual production needs. It can be transformed into a multi-head system, explosion-proof system, and overflow system. The Capping Machine is suitable for use in food, daily necessities, pesticides, and other industries, and has a broad application prospect.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. The company strictly controls the quality of the Capping Machine. If you are interested in Capping Machine, you can contact us, our website is www.cnzpack.com. I look forward to your coming and hope to cooperate with you.

Tube Filling machine And Sealing machine is suitable for filling all kinds of paste and high viscosity fluids, suitable for filling large-diameter plastic pipes and composite pipes, and then the pipe is heated inside, and the batch number and date are printed on the seal. Used in pharmaceutical, food, cosmetics, adhesive, and other industries. Next, let me tell you about the related introduction and features of the Tube Filling machine And Sealing machine. Here are some answers.

Here is the content list:

l The related introduction of Tube Filling machine And Sealing machine.

l Design features of Tube Filling machine And Sealing machine.

l Features of Tube Filling machine And Sealing machine.

The related introduction of Tube Filling machine And Sealing machine.

Tube Filling machine And Sealing machine is a machine that fills the packaging into the container and seals it. After the product is put into the packaging container, to keep the product sealed, maintain product quality, and avoid product loss, the packaging container needs to be sealed. Tube Filling machine And Sealing machine is a machine with a compact design and automatic tube feeding. Tube Filling machine And Sealing machine's tube washing, feeding marking, filling, folding, sealing, coding, and finished product output are all performed by a fully automatic control system. The feeding of the washing pipe adopts a pneumatic method, which is accurate and reliable.

Design features of Tube Filling machine And Sealing machine.

First, the Tube Filling machine And Sealing machine is mechatronics, using multiple-introduction technology, controlled by PLC, and can automatically complete tube feeding, partial color labeling, filling, sealing, and tube outlet at the same time. The machine runs smoothly, is easy to control and size conversion, and is suitable for the production of pasty products. Second, the Tube Filling Machine And the Sealing machine has modern modeling, strong practicability, and high processing value. Third, the Tube Filling Machine And the Sealing machine have a stainless steel volumetric bulldozing syringe and a Teflon piston seal to achieve accurate dosage.

Features of Tube Filling machine And Sealing machine.

Tube Filling machine And Sealing machine is a piece of high-tech equipment successfully developed by introducing foreign advanced technology and combining GMP requirements. It has the characteristics of reasonable structure, complete functions, convenient operation, accurate filling, stable operation, and low noise. Tube Filling machine And Sealing machine adopts PLC controller, from liquid or high-speed material filling to batch number printing (including production date) automatic operation, is cosmetics, pharmaceuticals, food, adhesives and other ALU tubes, plastic tubes and multi-tube filling Ideal equipment for sealing, in line with GMP standards.

Wenzhou Zungwan Intelligent Machine Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream, ointment, fluid, and semi-fluid materials. If you are engaged in work related to Tube Filling machine And Sealing machine or want to know more about our company, you can communicate with us on the website. Our official website is https:// www.cnzpack.com/. Our company adheres to the service tenet of "customer first", and implements the service of honesty and customer first.

With the continuous development of our production life, the emergence of Pharmaceutical Filler and Capper has brought great convenience to the industry. So what are the procedures and precautions for Pharmaceutical Filler and Capper? Let's take a look at it.

This is the content list:

l The operation method of Pharmaceutical Filler and Capper

l Safety rules for the use of Pharmaceutical Filler and Capper

l Precautions for Pharmaceutical Filler and Capper

The operation method of Pharmaceutical Filler and Capper

Pharmaceutical Filler and Capper installation precautions before use check, after the machine is installed, turn on the power, test runs the three-phase motor to ensure that the correct direction of operation, ensure that the pressure and flow of compressed air, check whether the motor, bearings, etc. need to be lubricated, no oil-free operation is strictly prohibited, normal before starting Pharmaceutical Filler and Capper. Filler And Capper at the same time, observe whether the fasteners of each part are loose, and only after the operation of each part is stable, can it be used normally. Check whether the function of the safety facilities of Pharmaceutical Filler and Capper is normal, check carefully whether there is water in all water tanks, whether the chainplate is stuck, whether there is debris on the conveyor belt, whether there are caps in the storage box, whether the water, power, and gas sources are connected before starting the machine. After all, conditions are ready, then close the main power QF, power indicator light, fault indicator, emergency stop indicator light is not on, then the start conditions are available, press the start button on the control box and the start switch at the filling, after the buzzer three warning, the whole machine starts running, take external washing, rinsing, filling fully automatic work mode, stop can be at the filling and control box press the stop button after the stop should turn off the main power.

Pharmaceutical Filler and Capper safety rules of use

1. No foreign objects (such as tools, rags, etc.) in Pharmaceutical Filler and Capper equipment.

2. Pharmaceutical Filler and Capper should not be allowed to have abnormal noise, if there is, it should be stopped immediately to check the reason.

3. All protective materials should be safe and reliable, it is strictly prohibited to wear clothing that may be hung by moving parts (such as scarves, bracelets, watches, etc.).

4. Long hair, should wear a hair cover.

5. Do not use water and other liquids to clean the electrical unit.

6. Cleaning should wear work clothes, gloves, glasses, etc., to prevent strong acid, strong alkali corrosion.

7. When Pharmaceutical Filler and Capper is running, someone must monitor it and do not approach the machine with tools or other objects.

8. Don't let the staff who are not related to the operation approach the installation of Pharmaceutical Filler and Capper.

Precautions for Pharmaceutical Filler and Capper

1、After unpacking Pharmaceutical Filler and Capper, first check whether the random technical information is complete and whether the machine is damaged in transportation, to solve the problem in time.

2、Install and adjust the feeding and discharging components according to the shape illustration in this manual.

3、Lubricate each lubrication point with new lubricant.

4、Turn the Pharmaceutical Filler and Capper by shaking the handle, check whether the Pharmaceutical Filler and Capper are running in the correct direction (facing the motor spindle in the counterclockwise direction), and the installation precautions of the Pharmaceutical Filler and Capper must be protected from grounding.

If you are interested in Pharmaceutical Filler and Capper, please contact us, our website is www.cnzpack.com.

Pharmaceutical Filler and Capper, whether semi-automatic or fully automatic, will encounter more or less in the process of using different places of failure, in the face of Pharmaceutical Filler and Capper's special parts of the failure, how do we find the problem as soon as possible and solve it? Let's take a look at it.

This is the content list:

l Pharmaceutical Filler and Capper's PLC failure

l Pharmaceutical Filler and Capper's Magnetic Switch Failure

l Pharmaceutical Filler and Capper solenoid valve failure

Pharmaceutical Filler and Capper PLC Failure

If the point controls Pharmaceutical Filler and Capper, the fault phenomenon is that the motor runs after the signal start Pharmaceutical Filler and Capper, but the motor does not stop running after the stop signal is issued. And Capper only stops running when the PLC is powered down. If the point controls the solenoid valve. The fault phenomenon is that the solenoid valve coil is not energized, and the cylinder is not reset. If the PLC of Pharmaceutical Filler and Capper is hit with external force to make the sticking point separate, it can assist to determine the fault of Pharmaceutical Filler and Capper.

Pharmaceutical Filler and Capper's magnetic switch failure

Pharmaceutical Filler and Capper's magnetic switch is used to detecting the position of the cylinder and control the cylinder travel. The four cylinders of laminating, pushing, pressing, and fusing knife are interrelated, and the magnetic switch is used to detect and control their positions. Pharmaceutical Filler and Capper failure is mainly manifested as the subsequent cylinders do not move, because the cylinder speed of Pharmaceutical Filler and Capper is faster, which causes the magnetic switch cannot detect the signal. Such as pushing the package cylinder speed is too fast, after pushing the package reset, the pressure package and fusion knife cylinder do not move.

Solenoid valve failure of Pharmaceutical Filler and Capper

Pharmaceutical Filler and Capper solenoid valve failure is mainly manifested as the cylinder does not move or does not reset, the reason is that Pharmaceutical Filler and Capper cylinder solenoid valve cannot change direction or tampering air. If the solenoid valve falters, the air pressure of Pharmaceutical Filler and Capper can't reach the working pressure because the inlet and outlet air paths are connected, and the knife beam doesn't rise to the place. the proximity switch of Pharmaceutical Filler and Capper knife beam protection doesn't work, and the precondition of full machine operation is not established. Pharmaceutical Filler and Capper does not operate, which is easily confused with an electrical fault. Solenoid valve air leakage sound, listen carefully to the source of sound and hand search for air leakage points, generally can easily identify the air leakage solenoid valve.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, with first-class product quality and efficient and fast after-sales service, forging the excellent products of "Central". Pharmaceutical Filler and Capper will undergo a lot of product testing before leaving the factory to reduce the probability of failure of Pharmaceutical Filler and Capper, and also provide customers with high-quality Pharmaceutical Filler and Capper warranty service. If you are interested in Pharmaceutical Filler and Capper, you can contact us, our website is www.cnzpack.com.

Celebrate the 10th anniversary of ZUNGWAN intelligent machine

——A letter from ZUNGWAN machine to you

Hello, partners, customers and friends of ZUNGWAN machine!

April 12 is the 10th anniversary of the establishment of ZUNGWAN intelligent machine. I'm 10 years old. From April 12, 2011 when I officially got my birth certificate (business license) to today, I've accompanied my close partners and colleagues through 10 spring, summer, autumn and winter, 10 special birthdays, and cooperated with more than 200 large, medium and small enterprises, companies and factories at home and abroad, It has sold more than 2000 automatic filling and sealing machines, more than 1000 automatic filling and capping machines, more than 3000 semi-automatic filling machines and more than 500 filling and packaging production lines.

My name is Wenzhou ZUNGWAN Intelligent Machine Co., Ltd. now has more than 50 employees. I am a well-known brand enterprise specializing in the R & D, production and sales of hose filling and sealing machine, aluminum tube filling and folding machine, various material filling and capping machine, full-automatic linear filling machine, capping machine, labeling machine, water cream filling and capping machine and other related packaging machinery and equipment supporting products, It has a complete and scientific quality management system. The enterprise integrity, company strength and product quality of ZUNGWAN Intelligent Machine have won the full support, trust and recognition of customers and friends at home and abroad.

Since the establishment of the company in 2011, our main sales and production staff have worked in the packaging machinery industry for more than 5 years. They have rich experience in R & D, production, sales and after-sales of cosmetics, skin care products and drug packaging production equipment. After successfully completing hundreds of enterprise order projects, Further promote our strategic sales of machinery and improve after-sales tracking service. In the next development period of the enterprise, it will participate more in the cooperation with famous brand companies, have a close relationship with cosmetics, skin care products, drugs and food enterprises, and create new brilliance in central machinery design, innovation and breakthrough with more like-minded people.

By combining the production technical strength of both supply and demand sides and using advanced machine professional knowledge, since 2011, we have been engaged in the sales of packaging machinery industry for more than 15 years. The chief engineer of filling and sealing machine production workshop, Potter and director Wu, who has been engaged in quality control for more than 20 years, have combined their own electronic pneumatic professional knowledge and years of technical training to launch various filling and sealing machines and filling capping machines, Plastic molding filling and sealing machine filling and sealing machine, fully meet the production requirements of customers and help customers create benefits; Time and again improve the service life of products and the simplicity of operation, so that the equipment I make is favored by enterprises, companies and factories at home and abroad.

I adhere to the enterprise oriented ideology and policy of "customer-oriented and product-based", so as to realize the integration of industrial chain, provide customers with multiple production engineering schemes, and provide packaging machinery and equipment with stable performance, excellent quality and reasonable price and immediate and thoughtful after-sales service, so as to solve actual production problems for customers with the most sincere attitude, Avoid unnecessary waste of expenses caused by enterprises. Strive to meet customers' purchase intention of value for money and value for money.

ZUNGWAN is the leading manufacturer of perfume and cosmetic filling machines and lines, providing all solutions from the smallest to the fastest machines (400 bpm) for a vast range of applications :

Perfumes (bottles, samples, miniatures), liquid Cosmetics (shampoo, conditioner, lotions, gel, serum, foam bath, liquid soap, shower gel, hair dye, nail varnish, foundation, makeup remover, suntan lotion, deodorant, roll-on, etc.) and Cosmetic creams (jars, lip-gloss, mascara).

Processing ?Packaging Machinery ?Catchup packing machine tomato paste pouch tomato sauce packing machine in Xiamen, China ... Packaging type: Bags, Film, Foil. Packaging material: Paper, Plastic. Automatic grade: Automatic. Driven type: Electric. Voltage: 220V 50/60Hz.

Price Range: Rs 500000-6000000/unit Other Details: Machines available with easy to use interface; Modular designs of the machine also takes less storage space; Machines requiring low capital investment

AUTOMATIC LINEAR ELECTRONIC VOLUMETRIC FILLING MACHINES FLUIDTRONIC MK VI AUTO This versatile, automatic linear liquid filler is equipped with 6 filling nozzles that utilize six sanitary, easily assembled stainless steel gear pump and accurately dispenses liquid in amounts from 50ml to 5 liters. Features

Product Description Manual Powder Filling Machine As a Manual Bottling Equipment manufacturer, We have a variety of models available in manual. and manual powder filling machine is used to package dry powder and granule, which is Made in Stainless steel . this type of Manual Powder Filling Machine is good for Food ,pharmaceutic,chemical packing

This vacuum bottle capping machin e is mainly applied in vacuum capping for round bottles, square bottles, fluted bottles, and other glass bottles, jars, cans. And it is widely used in lots of industries like the food

Automatic Filling Sealing Machine Prominent

Comparing eyedrop filling machine prices. You can easily wholesale quality eyedrop filling machine at wholesale prices on .

Inpak Vertical Packing Machine ? 8.50 Lakh / Number Ss Automation