Shop Advanced plastic tube filling and sealing machine manufacturer- China Suppliers Manufacturers Factory

In our production and life, the Liquid Filling Machine has a significant impact on many industries, so what is the method of using the Liquid Filling Machine? Let's go take a look next.

This is the content list:

l The ground wire must be well-grounded before the Liquid Filling Machine works

l Liquid Filling Machine liquid filling system assembly

The ground wire must be well-grounded before the Liquid Filling Machine works.

The ground wire must be well-grounded before the Liquid Filling Machine works, and then the appropriate standard syringe must be selected according to the different filling volumes. Generally, a 1ml syringe is used when the dispensing range is 0.2-1ml. Use a 5ml syringe for 1-5ml.use a 10ml syringe for 5-10ml. The 20ml model uses a 20ml glass infusion device. The 100ml model uses a 100ml glass infusion device, and the 500ml model uses the stainless steel filling system produced by our factory.

Liquid Filling Machine liquid filling system assembly　　

Pull out the inner core of the Liquid Filling Machine syringe, put the screw sleeve on the inner core of the syringe, and use the screw sleeve to properly fasten it to the lower base (cleanliness must be paid when disassembling the syringe). Place the upper clamp seat on the outlet end of the Liquid Filling Machine syringe jacket, and properly tighten the nuts on both sides to assemble the inner core and outer jacket of the installed Liquid Filling Machine syringe into one body. At this point, the Liquid Filling Machine injection system is assembled.

Place the Liquid Filling Machine valve with the arrow facing upwards and the arrow mark facing outwards and fix it on the fixing screw with a nut. Assemble the Liquid Filling Machine with a complete liquid filling system, align the upper and lower round holes of the liquid filling system components with the upper and lower fixing rods respectively, and put them on the bearing so that the outer end surface and the bearing surface are levels. When assembling the lower end, do not make the screw sleeve and the crank touch to prevent abnormal noise when the crank on the Liquid Filling Machine rotates (the screw sleeve and the crank are about 1mm apart when installed correctly). After the liquid filling system is installed correctly, tighten it. Tighten the screws up and down. Use a short hose to connect the Liquid Filling Machine syringe to the valve connection nozzle. The liquid inlet pipe is connected to the water inlet, and the liquid outlet pipe is connected to the water outlet. To prevent the liquid inlet and outlet pipes from being entangled, clip the liquid inlet and outlet pipes into the ear openings on the side of the casing.

Turn the crank of the Liquid Filling Machine by hand, it should be able to rotate freely, otherwise, the assembly is wrong, you should check whether the Liquid Filling Machine injection system is fastened to the rotating bearing.

Our company has obtained more than 20 invention patents and utility model patents. The main products are a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and online capping machine, capping machine and labeling machine, bottle unscrambler, tube filling and sealing machine, Cartoning machines, and other packaging equipment. If you are interested in Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.

In our production and life, Capping Machine is also called a Capping Machine, Capping Machine, or Capping Machine, which is used for screwing and unscrewing the caps of plastic bottles and glass bottles (molded bottles or tube bottles). equipment. Capping Machine is highly intelligent capping equipment with advanced technology, unique design, and easy operation. During the entire capping process, workers only need to place the cap on the mouth of the bottle, and then the bottle is automatically sent to the capping wheel and automatically tightened to complete the capping operation. The Capping Machine evacuates the packaging bottle and then tightens it, which prolongs the storage time of the packaging, reduces the failure rate of the Capping Machine, and improves the packaging efficiency of the Capping Machine. So what are the matters needing attention when operating Capping Machine correctly? Let's take a look together next.

This is the content list:

l Capping Machine rolling wheel adjustment

l Capping Machine lock wheel adjustment

l Capping Machine cap lock

l Capping Machine height adjustment

Capping Machine rolling wheel adjustment

Place the Capping Machine bottle on the bracket and raise the bracket to the highest point. First, loosen the lock nut to adjust the rolling wheel so that the (sprung) edge of the two Capping Machine rolling wheels is at the threading of the bottle. Click on it, then loosen the lock nut, and then adjust the adjusting screw so that the edges of the two rolling wheels are in contact with the cover, and a little pressure is appropriate, and then tighten the nut.

Capping Machine lock wheel adjustment

Adjust the two Capping Machine locking wheels, first loosen the locking nuts, adjust the locking wheels so that the edges of the two locking wheels are in contact with the lower edge of the bottle cap, a little pressure is appropriate, and then tighten the nuts (Note: Adjust Capping Machine Should be from loose to tight, adjust while pulling the lock).

Capping Machine cap lock

Loosen the top screw, remove the Capping Machine gland head, and then remove the entire Capping Machine lock head, install the appropriate plastic lock head on the cone sleeve, and then adjust the lifting height of the bracket to meet the working requirements.

Capping Machine height adjustment

Start the Capping Machine to lower the bracket to the lowest point, then place the bottle on the bracket, loosen the brake nut, turn the adjusting screw to raise the bracket, and then adjust the appropriate distance between the cap of the Capping Machine and the capping head (generally All are adjusted in place at the factory).

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. We have obtained ISO9001 quality management system certification, and some products have passed CE certification. Our company has obtained more than 20 invention patents and utility model patents. If you are interested in Capping Machine, you can contact us, our website is www.cnzpack.com.

Tube Filling machine And Sealing machine is suitable for filling all kinds of paste and high viscosity fluids, suitable for filling large-diameter plastic pipes and composite pipes, and then the pipe is heated inside, and the batch number and date are printed on the seal. Used in pharmaceutical, food, cosmetics, adhesive, and other industries. Next, let me tell you about the related introduction and features of the Tube Filling machine And Sealing machine. Here are some answers.

Here is the content list:

l The related introduction of Tube Filling machine And Sealing machine.

l Design features of Tube Filling machine And Sealing machine.

l Features of Tube Filling machine And Sealing machine.

The related introduction of Tube Filling machine And Sealing machine.

Tube Filling machine And Sealing machine is a machine that fills the packaging into the container and seals it. After the product is put into the packaging container, to keep the product sealed, maintain product quality, and avoid product loss, the packaging container needs to be sealed. Tube Filling machine And Sealing machine is a machine with a compact design and automatic tube feeding. Tube Filling machine And Sealing machine's tube washing, feeding marking, filling, folding, sealing, coding, and finished product output are all performed by a fully automatic control system. The feeding of the washing pipe adopts a pneumatic method, which is accurate and reliable.

Design features of Tube Filling machine And Sealing machine.

First, the Tube Filling machine And Sealing machine is mechatronics, using multiple-introduction technology, controlled by PLC, and can automatically complete tube feeding, partial color labeling, filling, sealing, and tube outlet at the same time. The machine runs smoothly, is easy to control and size conversion, and is suitable for the production of pasty products. Second, the Tube Filling Machine And the Sealing machine has modern modeling, strong practicability, and high processing value. Third, the Tube Filling Machine And the Sealing machine have a stainless steel volumetric bulldozing syringe and a Teflon piston seal to achieve accurate dosage.

Features of Tube Filling machine And Sealing machine.

Tube Filling machine And Sealing machine is a piece of high-tech equipment successfully developed by introducing foreign advanced technology and combining GMP requirements. It has the characteristics of reasonable structure, complete functions, convenient operation, accurate filling, stable operation, and low noise. Tube Filling machine And Sealing machine adopts PLC controller, from liquid or high-speed material filling to batch number printing (including production date) automatic operation, is cosmetics, pharmaceuticals, food, adhesives and other ALU tubes, plastic tubes and multi-tube filling Ideal equipment for sealing, in line with GMP standards.

Wenzhou Zungwan Intelligent Machine Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream, ointment, fluid, and semi-fluid materials. If you are engaged in work related to Tube Filling machine And Sealing machine or want to know more about our company, you can communicate with us on the website. Our official website is https:// www.cnzpack.com/. Our company adheres to the service tenet of "customer first", and implements the service of honesty and customer first.

The Mid-Autumn Festival is the second most important festival for a family reunion in China after the Spring Festival. Besides China, the Mid-Autumn Festival is also celebrated in many other Asian countries like Vietnam, Singapore, and Japan.

The Mid-Autumn Festival is also called the Moon Festival or Mooncake Festival. It would be celebrated on 21 September 2021. Gathering with families, eating moon cakes, and appreciating the fullest moon with lanterns, the Mid-Autumn Festival is a grand time for family reunions.

Besides those traditions in China, other Asian countries have their own unique customs of the Mid-Autumn Festival.

For example, the Mid-Autumn Festival is named Tết Trung Thu in Vietnamese. It is also known as a Children Festival. During the festival, parents will accompany their children and give them gifts like masks or lanterns. Most gifts are made by hand rather than buying at shops. Children would light lanterns and join in lion dance at the Mid-Autumn Festival.

Read Mid-Autumn Festival around the World to find more traditions in other countries.

In our production and life, the Cartoning Machine is of great significance to us, but sometimes, the Cartoning Machine will fail, so what is the reason for the failure of the Cartoning Machine? Next, let us analyze it together.

This is the content list:

• Stop or stop between conveyor belts

• The carton cannot be sucked down

• The carton is not formed or ejected at the mouth of the box feeding template after being sucked

• Can't suck the instructions

• The paper rebounds during the suction process of the manual

• The manual does not fold well

• Uneven folding of the manual

• There are curls and creases after the manual is folded

• Manual stuck in the fence

Stop or stop between conveyor belts

1. Cartoning Machine shuts down at intervals to check if there is a shortage of materials and automatically starts up when supplemented.

2. Shut down the Cartoning Machine to check whether the power supply including the power supply part, the motor, or the governor is normal.

The carton cannot be sucked down

1. Whether the cartons of Cartons Machine are arranged neatly.

2. Whether the cartons of the Cartoning Machine are pasted together.

3. Whether the air pressure of the Cartoning Machine suction head is normal.

The carton is not formed or ejected at the mouth of the box feeding template after being sucked

1. Check if the cartons of Cartons Machine are too hard.

2. Check whether the position of the guide rod of the cartons placed by the Cartoning Machine and the box delivery template are not correct.

3. Check whether the small hook spring at the rear of the Cartoning Machine delivery template is deformed.

4. Check if the height of the suction head of the Cartoning Machine and the box delivery track is correct.

Can't suck the instructions

1. Whether the Cartoning Machine manual is deformed, causing the suction head to fail to suck.

2. Whether the suction head gas of the Cartoning Machine is parallel to the manual.

3. Whether the paper width of the Cartoning Machine manual is different, the error must be within 1mm. The stacking position of the manual should be adjusted to a difference of 0.5mm from the inner edge when the suction head rises to the high position.

4. The small paper-separating hook above the suction head of the Cartoning Machine origami moves too early. Generally, the small hook should be inserted into the gap between the paper and the paper before the suction head is about to drop. The height of the small hook is adjusted to be 0.5mm away from the suction head when it is in the high position.

The paper rebounds during the suction process of the manual

1. The foot-lifting action of the Cartoning Machine's manual was too early, and the manual was taken away by the foot support before being pulled down. The position of the feet of the Cartoning Machine is so that it does not touch the sucked manual when it is returned and it returns to the high position when the paper picking notch wheel has not pulled the paper.

2. Whether the matching speed of the Cartoning Machine suction head and paper picking wheel is the same. The suction head of the Cartoning Machine should be lowered first, and then the front part of the paper picking notch wheel should be pressed onto the paper.

The manual does not fold well

1. Check if the Cartoning Machine paper is deformed and bent, and if there are burrs.

2. Is there any foreign matter in the fence of the Cartoning Machine blocking the paper?

3. The gap between the opening of the Cartoning Machine fence and the folding stick is too large, causing the paper to come out.

4. Is the gap between Cartons Machine's folding sticks too large to hold the paper? Adjust the adjusting screws at both ends of the folding stick to reduce the gap. If the Cartoning Machine folding stick has been used for too long and worn out, the folding stick must be replaced.

Uneven folding of the manual

Check the Cartoning Machine to adjust the front and rear positions of the barriers in the fence to achieve the required folding size.

There are curls and creases after the manual is folded

1. Is the gap between the Cartoning Machine baffle and the folding stick too large? Adjust the middle position of the baffle and folding stick.

2. If the middle position of the Cartoning Machine baffle and the folding stick has been adjusted, and there is still a large gap, remove the positioning pins on the Cartoning Machine baffle and re-adjust until the gap does not feed paper.

Manual stuck in the fence

1. Whether the paper feeding gap of Cartoning Machine folding stick is too large and paper feeding is weak. The adjustment method is the same as above.

2. The installation position of the lower half of the Cartoning Machine fence is too long than the arc guide plate on it so that the paper cannot enter the folding stick below. Loosen all the fixing screws on the Cartoning Machine fence and adjust the board backward, but it should not be shorter than the upper guide plate and should be 1-3 mm longer than the guide plate. If it is shorter than the guide plate, the Cartoning Machine manual may go directly into the folding stick below without folding.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It will conduct a large number of tests before the Cartoning Machine leaves the factory to reduce the failure of the Cartoning Machine and provide warranty services. If you are interested in the Cartoning Machine, you can contact us Contact, our website is www.cnzpack.com.

The Cosmetic Filling Machine and Capping machine is a professional cosmetic filling and capping equipment, which can make the cap tighter without damaging the mouth of the bottle and effectively protect the cosmetics from contact with the outside world. Next, let's take a look at the use and maintenance of the Cosmetic Filling machine and the capping machine. Here are some answers.

Here is the content list:

l Instructions for use of Cosmetic Filling machine And Capping machine.

l How is the daily maintenance of the Cosmetic Filling machine And Capping machine?

Instructions for use of Cosmetic Filling machine And Capping machine.

First, because the Cosmetic Filling Machine and Capping machine is an automated machine, the dimensions of the pop-up bottle, bottle liner, and bottle cap are required to be uniform. Second, before driving, you must first use the crank handle to turn the machine to see if there is any abnormality in the rotation, and then you can drive after it is confirmed that it is normal. Third, when adjusting the machine, the tools should be used appropriately. It is strictly forbidden to use excessive tools or excessive force to dismantle the parts to avoid damage to the machine parts or affect the performance of the machine. Fourth, the Cosmetic Filling machine and the Capping machine must be kept clean. Before the shift, all parts of the machine surface should be cleaned once, and clean lubricating oil should be added to each activity department. It should be scrubbed once a week, especially the areas that are not easily cleaned in normal use or blown with compressed air.

How is the daily maintenance of the Cosmetic Filling machine And Capping machine?

First, the Cosmetic Filling Machine and the Capping machine has strict requirements for the placement environment and must ensure the indoor humidity is moderate, ventilated, and hygienic. Because the Cosmetic Filling Machine and Capping machine is a mechanical device, after all, the raw materials are some steel electromechanical, etc. It is easy to rust when placed in a humid environment, and a closed environment is not conducive to the heat dissipation of the equipment during operation. Second, you must ensure that the power supply is normal and the grounding wire is safe before use. Voltage instability can cause considerable damage to the machine. Third, the non-woven soft cloth and cleaning agent must be added to wipe off the oil or dirt and wipe dry before the Cosmetic Filling machine and capping machine are operated. After use, take out all the remaining materials to prevent the materials from corroding the equipment and scrub them clean. Periodically clean the invisible dust and garbage in the chassis. And adhere to the tightness of the mechanical parts. Fourth, clean up the machine regularly. Many companies conduct major maintenance on machinery and equipment once a year in autumn. Fifth, add lubricating oil to the mechanical components of the Cosmetic Filling machine and Capping machine regularly to reduce frictional resistance and make the machine run faster.

Our official website is https:// www.cnzpack.com/. If you are engaged in work related to Cosmetic Filling machines and Capping machines or want to learn more about our company, you can communicate with us on the website.

Tube Filling machine And Sealing machine adopt the latest module circuit, stable working performance, high efficiency, and all components adopt famous brand products. Under the careful design of our company, various advanced Tube Filling Machine And Sealing machines have been produced. Mainly used for sealing toothpaste, cosmetics, medicine, food, industrial products, and various hoses. Next, let's take a look at the cleaning and maintenance of the Tube Filling machine And Sealing machine. Here are some answers.

Here is the content list:

• Tube Filling machine And Sealing machine cleaning.

• Daily maintenance of Tube Filling machine And Sealing machine.

Tube Filling machine And Sealing machine cleaning.

First, regularly clean the surface of the Tube Filling machine And Sealing machine, the bottom plate and the lower mold slide plate, grooves, the upper mold inner pressure plate, and the positioning rod. Second, grease should be added to the transmission parts of the lower mold slide plate, pressing rod bearing, eccentric wheel and guidepost, guide rail, and so on regularly to ensure the performance of the Tube Filling Machine And Sealing machine. Third, the method of cleaning the toothed knife: first plug the two drain holes of the lower mold with a cotton ball, pour boiling water into the groove of the lower mold, until it is full, then push the slide of the lower mold into place, and lower the upper mold. Press to the lowest point, let the toothed knife soak for a few minutes until it is clean, repeat several times.

Daily maintenance of Tube Filling machine And Sealing machine.

First, check the equipment ground wire frequently to ensure reliable contact; clean the weighing platform frequently; check whether the pneumatic pipeline is leaking and whether the air pipe is broken. Second, change the lubricating oil of the reducer motor every year, check the tightness of the chain, and adjust the tension in time. Third, the sensor of the Tube Filling Machine And Sealing machine is a high-precision, high-sealing, and high-sensitivity device. Impact and overload are strictly prohibited, and no contact is allowed during the working process, and it is not allowed to be disassembled if it is not required for maintenance. Fourth, if it is not used for a long time, empty the material in the pipeline. Fifth, observe the moisture filter and oil mist device of the pneumatic combination two-piece before going to work every day. Sixth, during the production, we should always patrol and observe the mechanical parts to see if the rotation and lifting are normal if there is any abnormality, and if the screws are loose. Seventh, do a good job of cleaning and sanitation, keep the surface of the Tube Filling machine And Sealing machine clean, often remove the accumulation on the scale body, and pay attention to keeping the electric control cabinet clean.

Wenzhou Zungwan Intelligent Machine Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream, ointment, fluid, and semi-fluid materials. If you are engaged in work related to Tube Filling machine And Sealing machine or want to know more about our company, you can contact us. Our official website is https:// www.cnzpack.com/.

Most Bag Packing Machines track and adjust various mechanical parameters through intelligent control instruments and menu-type software on the touch screen. The electronic display shows the length of the cut bag, the packaging speed, the net content of the filling, and the packaging output, etc., which can be understood at a glance. The standard color code tracking photoelectric system of the Bag Packing Machine can ensure the correct printing patterns of the packaged products. In addition, Bag Packing Machine can perform online status monitoring and fault diagnosis analysis of the working process. Once a problem occurs, Bag Packing Machine will automatically stop and display the cause and solution of the fault. So how do we maintain the Bag Packing Machine equipment in actual production? Let's take a look together next.

This is the content list:

l Maintenance after production

l Machine parts lubrication

l Care instructions

Maintenance after production

Every day after production, employees must clean the Bag Packing Machine before leaving get off work. First, the material barrels are cleaned in the warehouse, and the remaining materials on the tray are cleaned and kept clean. The remaining materials in other parts are cleaned up to prepare for the next use of the Bag Packing Machine.

Machine parts lubrication

The box part of the Bag Packing Machine is equipped with an oil gauge. The oil should be filled once before the Bag Packing Machine is turned on. It can be added in the middle according to the temperature rise and operating conditions of each bearing. The Bag Packing Machine worm gearbox must store oil for a long time. The oil level is high enough that the worm gear invades the oil. If it is used frequently, the oil must be replaced every three months. There is an oil plug at the bottom for draining oil. When refueling the Bag Packing Machine, do not let the oil spill out of the cup, let alone flow around the Bag Packing Machine and on the ground. Because oil is easy to pollute materials and affect product quality.

Care instructions

Check the parts of the Bag Packing Machine regularly, once a month, check whether the movable parts of the Bag Packing Machine worm gear, worm, lubricating block, bearings, and other moving parts are flexible and worn. If any defects are found, they should be repaired in time and should not be used reluctantly. The Bag Packing Machine should be used in a dry and clean room, and should not be used in places where the atmosphere contains acids and other gases that are corrosive to the body. When the Bag Packing Machine roller moves back and forth during work, please adjust the screws on the front bearing to the proper position. If the gear shaft of the Bag Packing Machine moves, please adjust the screws behind the bearing frame to the proper position, adjust the gap so that the bearing does not make a noise, turn the belt pulley by hand, and tighten properly. Too tight or too loose can make the Bag Packing Machine happen. The possibility of damage. If it is out of service for a long time, the Bag Packing Machine must be wiped and cleaned, and the smooth surface of the machine must be coated with anti-rust oil and covered with a cloth canopy.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that produces first-class Bag Packing Machine product quality and efficient and fast after-sales service, which has created excellent products of "Zhonghuan". Products are in great demand in the domestic and foreign markets. Keep improving, develop to satisfy customers, and meet market demands are our eternal topic and our sincere commitment to customers. If you are interested in Bag Packing Machine, you can contact us, our website is www.cnzpack.com.

Horizontal cartoners come standard with a carton magazine. The carton magazine’s function is to supply cartons to the rotary feeder, on demand, by a simple feed system. We offer extended magazines to handle your operational needs. Rotary Carton Pick

Leading Manufacturer of dish wash liquid filling machine, glass bottle filling machine, fruit …

We are experts in filling and capping machines. We supply top quality filling and capping machines to the food and beverage, pharmaceutical and general manufacturing industries. …

HYTB1-150B Automatic Flat and Round Bottle One Label Labeling Machine Product Item：HYTB1-150B Labeling speed: 50-150 BPH Machinery Capacity: 150BPM Function: One label applicator Marketing Type: Ordinary Product round bottle labeling machine , glass round bottle sticker labeler , plastic flat bottle one side label application Inquiry Send Email

ZHF-80Z Metal Laminated Tube Filling And Sealing Machine video ZHF-60Z Ultrasonic Metal Tube Filling And Sealing Machine video ZHF-100A plastic aluminum Tube Filling And Sealing Machine video ZHF-100YC Plastic Tube Filling

Sora Machine offers you high speed continuous motion rotary filling lines by assuring up to 150,200,250,300 cans per min (CPM) depending on number of the heads of entire line Depalletizer Vacuum or Magnetic special table for 100-400 ml cans Vacuum Separator, carton separation system Digital electronic control panel

WHOLESALE PERFUME, FRAGRANCES, COLOGNE

The RL-HG 540 Labeler is the perfect machine for any high volume Hot Melt Glue labeling …