After the Labeling machine sensor sends a signal that the labeling object is ready to be labeled, the drive wheel on the Labeling machine turns up. As the rolled label is in a tight state on the equipment, when the Labeling machine backing paper is tightly attached to the peeling plate and changes direction, the Labeling machine label is forced to disengage due to the rigidity of its material and is ready to be labeled. At this time, the labeling object is located just below the label, under the action of the labeling wheel, to achieve synchronous labeling. After the Labeling machine has finished labeling, the sensor under the roll label sends a stop signal, the drive wheel comes to a standstill, and a labeling cycle end. No matter which type of Labeling machine, the labeling process is roughly the same. The difference is that the installation position of the Labeling machine is different, the labeling object is conveyed differently and positioned differently, and the form of the labeling roller of the Labeling machine is also different. So, what are the Labeling machine's requirements for labels? Let's look at it together next.
This is the content list:
l Surface material
l Release force
l At the end of the paper
l Processing quality
Labeling machine label stiffness is the key to labeling, so the Labeling machine surface material is required to have a certain strength and hardness. Labeling machine label stiffness and the thickness of the material and the area of the label, so the Labeling machine in the use of soft film material should be appropriate to increase its thickness, generally controlled at 100μm or more. Labeling machine thin paper materials, such as 60 ~ 70g/m2 labeling paper, are generally not suitable for the production of large labels, but suitable for processing into small labels, such as price tags used on the price tag. Labeling machine label stiffness is not good, it will cause labeling out of the label, or label and backing paper reward so that the automatic labeling failure.
Labeling machine peel-off force is the force at which the label is separated from the backing paper by the Labeling machine. The Labeling machine release force is related to the type and thickness of the adhesive, the silicone coating on the surface of the backing paper, and the ambient temperature at the time of labeling. If the Labeling machine release force is too small, the label will easily fall off (leave the backing paper) during the conveying process. The Labeling machine's release force is too large, the label will be difficult to detach from the backing paper, and it will not be able to produce labels. The Labeling machine should be integrated control of the technical indicators so that the release force is maintained within a reasonable range.
At the end of the paper
Is also an important indicator to control automatic labeling. The requirements of the Labeling machine base paper surface silicon-coated evenly, the Labeling machine peeling force is consistent. Uniform thickness and good tensile strength ensure that the Labeling machine will not break when labeling. Uniform thickness and good light transmission of the Labeling machine ensure that the sensor can correctly identify the location of the label.
Requires that both sides of the Labeling machine backing paper after slitting should be flat and free of fracture to avoid the backing paper from breaking when the tension changes. Labeling machine die-cutting, to avoid cutting through the backing paper or damage to the silicone layer. If the Labeling machine backing paper and silicone coated layer are destroyed, the Labeling machine backing paper will break easily or the glue in the label will penetrate the backing paper. In addition, the static electricity in the web label must be eliminated before Labeling machine labeling, because static electricity will lead to Labeling machine labeling failure or labeling inaccuracy.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. Before the Labeling machine leaves the factory, it will conduct a large number of tests on the Labeling machine to maintain the healthy development of the Labeling machine market. If you are interested in the Labeling machine, you can contact us, our website is www.cnzpack.com.
As people are enjoying life more and more now, most of the manual labor has been replaced. It is machine consumption. Mechanized operations not only restrict our hands, but more importantly, machine consumption is more efficient than our manual work. It is not only a little bit higher but also more hygiene, which has many benefits. Cartoning Machine is one such automated equipment. So, what are the feed inlets and characteristics of the Cartoning Machine? Let's go take a look next.
This is the content list:
l The feed inlet of the Cartoning Machine
l Features of Cartoning Machine
The feed inlet of the Cartoning Machine
Cartoning Machine feed is generally divided into three entrances: manual entrance, medicine bottle entrance, and machine package box entrance. The entire process of the Cartoning Machine from the machine package box feeding to the final packaging molding can be roughly divided into four stages: the carton is fixed by a guide rail and a push plate is used to open the carton. At the same time, there will be two cards that can move forward. The position is raised from below, jamming the sides of the carton from front to back, so that the box opens at a right angle and moves forward to the loading area.
After filling in the Cartoning Machine loading area, the mechanism of the machine folds the ears into the left and right guide rails and then performs the lid closing action. The front mechanism of the Cartoning Machine will first bend the tongue of the carton, and then a push plate pushes the lid to bend so that the tongue is inserted into the box and the lock is fastened. The closing action of the Cartoning Machine is critical, and the quality of the completion has a lot to do with the structure of the carton and the accuracy of the machine adjustment.
Features of the cartooning machine
1. Cartoning Machine has a low cost. Cartoning Machines can continue to work 24 hours a day. As long as the regular maintenance work is done, it can continue to produce as much as possible, and the production line only needs one or two people to take care of it, which effectively saves labor costs. Moreover, since the work of the Cartoning Machine is mass production, the products produced are more up to the standard with small differences. In addition to the high labor costs and individual differences in products, manual packaging is also affected by the emotions of workers.
2. Cartoning Machine has high production efficiency. The Cartoning Machine takes a fixed amount of time to complete a piece of cartooning work. In a fixed period, the total amount of products that can be completed is also fixed, and it will not be fluctuating. For enterprises, it is easier to calculate and control the cost. In addition, the Cartoning Machine has a fixed time to complete a piece of boxing work, and its efficiency is relatively improved. It can reduce the pressure on the staff in related positions, better manage, make the work orderly, and create more profits for the enterprise. many.
3. The Cartoning Machine has a high safety factor. Manual cartooning is unavoidable for negligence and fatigue, and accidents are prone to work accidents. The Cartoning Machine is used throughout the machine, with high accuracy of repeated operations, good stability, and strong safety. It can effectively prevent injuries to workers. Contribute to the safe and civilized production of enterprises.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It has a lot of experience in the production of cartooning machines. A large number of tests have been carried out before the Cartoning Machine leaves the factory to ensure the quality of the Cartoning Machine. If you are interested, you can contact us, our website is www.cnzpack.com.
Wenzhou Zungwan Intelligent Machine Co.,Ltd. is the professional equipment manufacturer to keep researching and developing the packing machinery for every type of liquid, powder, cream/ointment, fluid and half-fluid etc. materials. We have Obtained ISO9001 quality management system authentication and parts of our products have passed CE authentication. Our company has obtained more than 20 invention patents and utility model patents. The main products range from nail polish filling machine, perfume machine,perfume filling machine, powder serial automatically volume-measuring packing machine and inline capping machine, rotary capping machine and labeling machine, bottle unscrambler , screw capping machine ,tube filling and sealing machine, cartoning machine and other Packaging equipments.
So far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and our service as well as our integrity is acclaimed both in China and abroad. we will carry forward the spirit of "integrated innovation, and perseverance," discipline ourselves to be the first, and provide better and more perfect service for our new and old customers with enthusiasm and a new attitude.
The Cosmetic Filling Machine and Capping machine is a professional cosmetic filling and capping equipment, which can make the cap tighter without damaging the mouth of the bottle and effectively protect the cosmetics from contact with the outside world. Next, let's take a look at the use and maintenance of the Cosmetic Filling machine and the capping machine. Here are some answers.
Here is the content list:
l Instructions for use of Cosmetic Filling machine And Capping machine.
l How is the daily maintenance of the Cosmetic Filling machine And Capping machine?
Instructions for use of Cosmetic Filling machine And Capping machine.
First, because the Cosmetic Filling Machine and Capping machine is an automated machine, the dimensions of the pop-up bottle, bottle liner, and bottle cap are required to be uniform. Second, before driving, you must first use the crank handle to turn the machine to see if there is any abnormality in the rotation, and then you can drive after it is confirmed that it is normal. Third, when adjusting the machine, the tools should be used appropriately. It is strictly forbidden to use excessive tools or excessive force to dismantle the parts to avoid damage to the machine parts or affect the performance of the machine. Fourth, the Cosmetic Filling machine and the Capping machine must be kept clean. Before the shift, all parts of the machine surface should be cleaned once, and clean lubricating oil should be added to each activity department. It should be scrubbed once a week, especially the areas that are not easily cleaned in normal use or blown with compressed air.
How is the daily maintenance of the Cosmetic Filling machine And Capping machine?
First, the Cosmetic Filling Machine and the Capping machine has strict requirements for the placement environment and must ensure the indoor humidity is moderate, ventilated, and hygienic. Because the Cosmetic Filling Machine and Capping machine is a mechanical device, after all, the raw materials are some steel electromechanical, etc. It is easy to rust when placed in a humid environment, and a closed environment is not conducive to the heat dissipation of the equipment during operation. Second, you must ensure that the power supply is normal and the grounding wire is safe before use. Voltage instability can cause considerable damage to the machine. Third, the non-woven soft cloth and cleaning agent must be added to wipe off the oil or dirt and wipe dry before the Cosmetic Filling machine and capping machine are operated. After use, take out all the remaining materials to prevent the materials from corroding the equipment and scrub them clean. Periodically clean the invisible dust and garbage in the chassis. And adhere to the tightness of the mechanical parts. Fourth, clean up the machine regularly. Many companies conduct major maintenance on machinery and equipment once a year in autumn. Fifth, add lubricating oil to the mechanical components of the Cosmetic Filling machine and Capping machine regularly to reduce frictional resistance and make the machine run faster.
Our official website is https:// www.cnzpack.com/. If you are engaged in work related to Cosmetic Filling machines and Capping machines or want to learn more about our company, you can communicate with us on the website.
Tube filling machine and sealing machine is advanced equipment for sealing plastic pipes and aluminum-plastic pipes. It uses the thermal shock effect of the plastic tube produced by the ultrasonic sealing transducer and quickly melts the adhesive. The tube Filling machine And the Sealing machine does not need to add any additives, even if the surface is contaminated, it will not affect the sealing effect. Next, let's take a look at the advantages and applications of the Tube Filling machine And Sealing machine. Here are some answers.
Here is the content list:
Advantages of Tube Filling machine And Sealing machine.
Application field of Tube Filling machine And Sealing machine.
First, the servo motor controls the filling, and 8 nozzles are filled at the same time. Second, the Tube Filling Machine And the Sealing machine can achieve fast cleaning, fast adjustment, and step-less adjustment of the volume cylinder speed. The tube Filling machine And the Sealing machine is suitable for filling different specifications and different liquids. Third, the filling volume only needs to be adjusted once, each volume cylinder is fine-tuned, the filling accuracy is high and the consistency is good. The contact material part is 316L stainless steel and silicon rubber, which meets the GMP standard. Fourth, the filling piston-cylinder adopts imported geared motor step-less speed regulation, which is suitable for aqueous liquids and viscous liquids. Fifth, imported electromagnetic clutches and brakes eliminate inertia and high filling accuracy. Sixth, the man-machine interface communicates with the PLC. You can debug the device and change the type with simple settings on the screen. Seventh, bottling, positioning, filling, and discharging are all automatic. If the bottle is not in the correct position, the bottle is blocked, or the filling tube is not inserted into the bottle during filling, the equipment will automatically protect and continue to operate after troubleshooting.
Tube filling machine and sealing machine is mainly used to fill ointment or viscous fluid materials into aluminum tubes, plastic tubes, or composite tubes. Then seal the end of the tube. The Tube Filling machine And Sealing machine adopts a new type of stainless steel butterfly valve dosing pump and a screw fine adjustment device. In addition, the Tube Filling Machine And Sealing machine is widely used for filling, sealing, and batch number printing of aluminum tube packaging products in cosmetics, toothpaste, ointment, food, shoe polish, adhesives, etc. Tube Filling machines And Sealing machines can also be widely used in product packaging in medicine, daily chemical, food, chemical, and other industries. Such as ointment, adhesive, silica gel, AB glue, skin cream, hair dye, shoe polish, toothpaste, and other liquid or paste-like materials filling and sealing.
Our official website is https:// www.cnzpack.com/. If you are engaged in work related to Tube Filling machine And Sealing machine or want to know more about our company, you can communicate with us on the website. Our company adheres to the corporate culture of "quality-oriented, customer first", and has always made unremitting efforts to become a professional Tube Filling machine And Sealing machine supplier in the industry.
With the continuous development of our production life, the emergence of Pharmaceutical Filler and Capper has brought great convenience to the industry. So what are the procedures and precautions for Pharmaceutical Filler and Capper? Let's take a look at it.
This is the content list:
l The operation method of Pharmaceutical Filler and Capper
l Safety rules for the use of Pharmaceutical Filler and Capper
l Precautions for Pharmaceutical Filler and Capper
The operation method of Pharmaceutical Filler and Capper
Pharmaceutical Filler and Capper installation precautions before use check, after the machine is installed, turn on the power, test runs the three-phase motor to ensure that the correct direction of operation, ensure that the pressure and flow of compressed air, check whether the motor, bearings, etc. need to be lubricated, no oil-free operation is strictly prohibited, normal before starting Pharmaceutical Filler and Capper. Filler And Capper at the same time, observe whether the fasteners of each part are loose, and only after the operation of each part is stable, can it be used normally. Check whether the function of the safety facilities of Pharmaceutical Filler and Capper is normal, check carefully whether there is water in all water tanks, whether the chainplate is stuck, whether there is debris on the conveyor belt, whether there are caps in the storage box, whether the water, power, and gas sources are connected before starting the machine. After all, conditions are ready, then close the main power QF, power indicator light, fault indicator, emergency stop indicator light is not on, then the start conditions are available, press the start button on the control box and the start switch at the filling, after the buzzer three warning, the whole machine starts running, take external washing, rinsing, filling fully automatic work mode, stop can be at the filling and control box press the stop button after the stop should turn off the main power.
Pharmaceutical Filler and Capper safety rules of use
1. No foreign objects (such as tools, rags, etc.) in Pharmaceutical Filler and Capper equipment.
2. Pharmaceutical Filler and Capper should not be allowed to have abnormal noise, if there is, it should be stopped immediately to check the reason.
3. All protective materials should be safe and reliable, it is strictly prohibited to wear clothing that may be hung by moving parts (such as scarves, bracelets, watches, etc.).
4. Long hair, should wear a hair cover.
5. Do not use water and other liquids to clean the electrical unit.
6. Cleaning should wear work clothes, gloves, glasses, etc., to prevent strong acid, strong alkali corrosion.
7. When Pharmaceutical Filler and Capper is running, someone must monitor it and do not approach the machine with tools or other objects.
8. Don't let the staff who are not related to the operation approach the installation of Pharmaceutical Filler and Capper.
Precautions for Pharmaceutical Filler and Capper
1、After unpacking Pharmaceutical Filler and Capper, first check whether the random technical information is complete and whether the machine is damaged in transportation, to solve the problem in time.
2、Install and adjust the feeding and discharging components according to the shape illustration in this manual.
3、Lubricate each lubrication point with new lubricant.
4、Turn the Pharmaceutical Filler and Capper by shaking the handle, check whether the Pharmaceutical Filler and Capper are running in the correct direction (facing the motor spindle in the counterclockwise direction), and the installation precautions of the Pharmaceutical Filler and Capper must be protected from grounding.
If you are interested in Pharmaceutical Filler and Capper, please contact us, our website is www.cnzpack.com.
In our daily life, Capping Machine plays a vital role for us, so what are the main work processes and precautions of the Capping Machine? Let's take a look together next.
This is the content list:
The main workflow of Capping Machine
How to carry out daily maintenance and maintenance of Capping Machine
How to deal with common problems of Capping Machine
We know that after the plastic bottles are sorted by the Capping Machine, they enter the conveyor chain in a single row. In the filling station, the plunger pump injects the liquid in the container into the plastic bottle. After filling, the plastic bottle enters the index plate and stops accurately at the capping station. Manually place the cap of the Capping Machine at the entrance of the friction beltline, take out the capping claw, screw the cap claw, and squeeze the tube claw to complete the capping action. Then the plastic bottle exits the index plate and enters the conveyor chain, and enters the labeling station to complete the round bottle labeling.
1. Always keep the Capping Machine clean, especially for the electrical appliances on the switchboard, to prevent moisture and dust, and it is forbidden to change the program of the inverter and the program controller at will.
2. The power supply voltage of the Capping Machine should be stable, not exceeding ±15%, the material temperature should be kept at 10℃-40℃, the ambient temperature should be kept at 5℃～40℃, and the temperature should be kept at 5～95%PH.
3. The flowmeter used by the Capping Machine for spray filling is a precision instrument. Therefore, the oil must be precision filtered before it can be filled.
4. Turn off the power supply and oil inlet valve of the Capping Machine after finishing the work.
5. Pay attention to the cleanliness of the infrared sensor from the Capping Machine. Frequently wipe it clean with clean cotton. It is strictly forbidden for any object to approach the sensor during the working process, and strong light should not be directly or reflected on the sensor, otherwise, it will prosper and malfunction.
6. Add cylinder lubricating oil to the pneumatic triplet regularly.
7. When the machine is not used for a long time, all parts should be wiped clean and covered with plastic or tarpaulin to prevent dust.
First, what should I do if the cylinder piston of the Capping Machine does not work? Confirm whether the safety emergency stop switch is safe. Confirm that the air supply switch of the Capping Machine is turned on. Check if the Capping Machine one-way signal valve is damaged.
Second, what should I do if the Capping Machine cylinder piston does not return after being pushed to the top? Confirm whether the moving target is in contact with the one-way valve.
Third, how to adjust the filling volume of the Capping Machine is inaccurate or not discharged?
Check whether the upper and lower throttle valves of the Capping Machine are closed, and increase the pumping speed of the throttle valve of the cylinder. Make sure that the Capping Machine quick-install tee is locked with a clamp. Confirm whether there are enough materials in the Capping Machine storage box. Make sure that the joints of the pipes of the Capping Machine are sealed.
Fourth, what should I do if the material of the Capping Machine flows out from the rear end of the cylinder? Check whether the sealing ring on the Capping Machine piston is worn. If it is worn, replace it and make sure that the piston and the piston rod are tight.
In addition to timely handling of problems, it is also necessary to do a good job of preventive work in advance. Doing a good job in daily maintenance can also reduce the failure rate of the Capping Machine. The daily maintenance and maintenance of the Capping Machine cannot be underestimated. This is a very important step. Daily maintenance on time can effectively extend the service life of the Capping Machine, improve the production efficiency of the enterprise, and keep Capping Machine in normal operation throughout the day, reducing manpower. The loss of material resources.
Wenzhou Zungwan Intelligent Machinery Co., Ltd.'s first-class product quality and efficient and quick after-sales service have created excellent products of "Zhonghuan". Products are in great demand in the domestic and foreign markets. Keep improving, develop to satisfy customers, and meet market demands are our eternal topic and our sincere commitment to customers. Therefore, Capping Machine is very popular among consumers. If you are interested in Capping Machine, you can contact us. Our website is www.cnzpack.com.
The Cosmetic Filling machine And Capping machine integrates the functions of air purification, filling, inserting, capping, and venting. It is suitable for filling water injection, lotion, and cream products. The Cosmetic Filling machine And Capping machine has the advantages of reasonable design, stable performance, accurate quantity, glass tabletop, automatic bottle feeding, smooth operation and no noise, electric speed regulation of filling speed and filling volume, and convenient maintenance and cleaning. Next, let's take a look at the description and structural characteristics of the Cosmetic Filling machine And capping Machine. Here are some answers.
Here is the content list:
Description of Cosmetic Filling machine And Capping machine.
Structural characteristics of Cosmetic Filling machine And Capping machine.
The Cosmetic Filling machine And Capping machine adopts automatic low-vacuum filling, automatic bottle detection (no bottle no filling), three fillings, automatic lowering of the nozzle cap, circulation of the perfume bottle die, and wide adaptability. It can meet the volume of containers of different sizes and filling requirements. Cosmetic Filling Machine And Capping machine is equipped with air bottle cleaning, quantitative filling, negative pressure filling, pumping, roll cap, jacket, screw cap, rejection, labeling, and finished product collection. The mold moves in a circular motion, which makes it easy to change the bottle. The stepper motor is used for quantitative filling, and the filling volume can be adjusted quickly. The negative pressure device is used to fill the same liquid level and the manipulator releases the pump to increase the pump roll rate; the elastic rolling head is to avoid damage to the bottle body.
The design of the Cosmetic Filling machine And Capping machine is very reasonable. The Cosmetic Filling machine And Capping machine has a reasonable and compact structure, stable operation, flexible operation, and convenient specification conversion and adjustment. The speed of the aluminum cover is adjustable. Using the principle of seven-station three-knife cap rolling, the aluminum cap is rolled without damage, and the rolling mouth is firm, smooth and flat. The operation of the machine is very simple. The internal pneumatic part adopts new pneumatic components. The piston and cylinder of cylinder are made of PTFE and stainless steel, which meets the requirements of GMP testing. The filling speed can be adjusted at will with high precision. The Cosmetic Filling machine And Capping machine can be modified according to actual production needs and can be transformed into a multi-head type, explosion-proof type, and overflow type system.
Wenzhou Zungwan Intelligent Machine Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream, ointment, fluid, and semi-fluid materials. Our official website is https:// www. cnzpack.com/. If you are engaged in work related to Cosmetic Filling machines And Capping machines or want to learn more about our company, you can communicate with us on the website. Our company adheres to the service tenet of "customer first", and implements the service of honesty and customer first.