











In our production and life, the Liquid Filling Machine has a significant impact on many industries, so what is the method of using the Liquid Filling Machine? Let's go take a look next.
This is the content list:
l The ground wire must be well-grounded before the Liquid Filling Machine works
l Liquid Filling Machine liquid filling system assembly
The ground wire must be well-grounded before the Liquid Filling Machine works.
The ground wire must be well-grounded before the Liquid Filling Machine works, and then the appropriate standard syringe must be selected according to the different filling volumes. Generally, a 1ml syringe is used when the dispensing range is 0.2-1ml. Use a 5ml syringe for 1-5ml.use a 10ml syringe for 5-10ml. The 20ml model uses a 20ml glass infusion device. The 100ml model uses a 100ml glass infusion device, and the 500ml model uses the stainless steel filling system produced by our factory.
Liquid Filling Machine liquid filling system assembly
Pull out the inner core of the Liquid Filling Machine syringe, put the screw sleeve on the inner core of the syringe, and use the screw sleeve to properly fasten it to the lower base (cleanliness must be paid when disassembling the syringe). Place the upper clamp seat on the outlet end of the Liquid Filling Machine syringe jacket, and properly tighten the nuts on both sides to assemble the inner core and outer jacket of the installed Liquid Filling Machine syringe into one body. At this point, the Liquid Filling Machine injection system is assembled.
Place the Liquid Filling Machine valve with the arrow facing upwards and the arrow mark facing outwards and fix it on the fixing screw with a nut. Assemble the Liquid Filling Machine with a complete liquid filling system, align the upper and lower round holes of the liquid filling system components with the upper and lower fixing rods respectively, and put them on the bearing so that the outer end surface and the bearing surface are levels. When assembling the lower end, do not make the screw sleeve and the crank touch to prevent abnormal noise when the crank on the Liquid Filling Machine rotates (the screw sleeve and the crank are about 1mm apart when installed correctly). After the liquid filling system is installed correctly, tighten it. Tighten the screws up and down. Use a short hose to connect the Liquid Filling Machine syringe to the valve connection nozzle. The liquid inlet pipe is connected to the water inlet, and the liquid outlet pipe is connected to the water outlet. To prevent the liquid inlet and outlet pipes from being entangled, clip the liquid inlet and outlet pipes into the ear openings on the side of the casing.
Turn the crank of the Liquid Filling Machine by hand, it should be able to rotate freely, otherwise, the assembly is wrong, you should check whether the Liquid Filling Machine injection system is fastened to the rotating bearing.
Our company has obtained more than 20 invention patents and utility model patents. The main products are a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and online capping machine, capping machine and labeling machine, bottle unscrambler, tube filling and sealing machine, Cartoning machines, and other packaging equipment. If you are interested in Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.
Due to the particularity of the environment in which the Liquid Filling Machine equipment is used, the structure of the metal itself is prone to corrosion. The external environment such as temperature, humidity, and air will directly cause the metal to corrode. After the Liquid Filling Machine equipment is corroded, the color, appearance, and basic performance of the machine may change, which causes damage to the machine equipment and also causes a waste of energy, causing the company to suffer a greater loss. To reduce the damage of the Liquid Filling Machine caused by corrosion, we should do anti-corrosion work during design, production, and later use. So what are the anti-corrosion methods of Liquid Filling Machines? Let's take a look together next.
This is the content list:
Selection of Liquid Filling Machine materials
Liquid Filling Machine structure and process
Liquid Filling Machine corrosion inhibitor
Most of the Liquid Filling Machine equipment materials used in the manufacturing industry are carbon steel. The price of this kind of steel is relatively low, and at the same time, it is more convenient to purchase and easy to process. Such steel will not cause major corrosion when used in the ordinary working environment, and will not cause major harm to the use of Liquid Filling Machine equipment. But if it is used in an enterprise, its working environment may cause serious erosion.
If the collective shape design of the Liquid Filling Machine components is too complicated or unreasonable, it may cause defects such as thermal stress, dust accumulation, Liquid Filling Machine stress, and liquid accumulation, which may lead to corrosion in the connecting and unloading parts. From the perspective of anti-corrosion, comprehensive consideration is given to the design of the Liquid Filling Machine structure.
Liquid Filling Machine corrosion inhibitor is a chemical substance that is added to the corrosion inhibitor system at a proper concentration, which can significantly reduce the corrosion rate of the metal and has a small effect on the concentration of the corrosive agent. The amount of Liquid Filling Machine corrosion inhibitor is very small. Although it cannot change the corrosion tendency of the metal in the medium, it can form a protective film on the metal surface to slow down the corrosion rate of the metal, thereby reducing the corrosion of the metal.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. So far, we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and services as well as our integrity are widely praised at home and abroad. Before the Liquid Filling Machine leaves the factory, the corrosion resistance of the Liquid Filling Machine will be enhanced. If you are interested in the Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.
In our production and life, Capping Machine is also called a Capping Machine, Capping Machine, or Capping Machine, which is used for screwing and unscrewing the caps of plastic bottles and glass bottles (molded bottles or tube bottles). equipment. Capping Machine is highly intelligent capping equipment with advanced technology, unique design, and easy operation. During the entire capping process, workers only need to place the cap on the mouth of the bottle, and then the bottle is automatically sent to the capping wheel and automatically tightened to complete the capping operation. The Capping Machine evacuates the packaging bottle and then tightens it, which prolongs the storage time of the packaging, reduces the failure rate of the Capping Machine, and improves the packaging efficiency of the Capping Machine. So what are the matters needing attention when operating Capping Machine correctly? Let's take a look together next.
This is the content list:
l Capping Machine rolling wheel adjustment
l Capping Machine lock wheel adjustment
l Capping Machine cap lock
l Capping Machine height adjustment
Capping Machine rolling wheel adjustment
Place the Capping Machine bottle on the bracket and raise the bracket to the highest point. First, loosen the lock nut to adjust the rolling wheel so that the (sprung) edge of the two Capping Machine rolling wheels is at the threading of the bottle. Click on it, then loosen the lock nut, and then adjust the adjusting screw so that the edges of the two rolling wheels are in contact with the cover, and a little pressure is appropriate, and then tighten the nut.
Capping Machine lock wheel adjustment
Adjust the two Capping Machine locking wheels, first loosen the locking nuts, adjust the locking wheels so that the edges of the two locking wheels are in contact with the lower edge of the bottle cap, a little pressure is appropriate, and then tighten the nuts (Note: Adjust Capping Machine Should be from loose to tight, adjust while pulling the lock).
Capping Machine cap lock
Loosen the top screw, remove the Capping Machine gland head, and then remove the entire Capping Machine lock head, install the appropriate plastic lock head on the cone sleeve, and then adjust the lifting height of the bracket to meet the working requirements.
Capping Machine height adjustment
Start the Capping Machine to lower the bracket to the lowest point, then place the bottle on the bracket, loosen the brake nut, turn the adjusting screw to raise the bracket, and then adjust the appropriate distance between the cap of the Capping Machine and the capping head (generally All are adjusted in place at the factory).
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. We have obtained ISO9001 quality management system certification, and some products have passed CE certification. Our company has obtained more than 20 invention patents and utility model patents. If you are interested in Capping Machine, you can contact us, our website is www.cnzpack.com.
Liquid Filling Machine is used in the beverage, drinking water, and liquor industries and has become a very important equipment in the liquid food industry. function. So what are the main structural designs of Liquid Filling Machine? Let's take a look at it together.
This is the content list:
l The transmission system of Liquid Filling Machine
l Liquid Filling Machine's actuator
l Liquid Filling Machine's control system
l The body part of the Liquid Filling Machine
The transmission system of Liquid Filling Machine
Liquid Filling Machine's transmission system, this part is to transmit power and motion to various actuators, control elements, and auxiliary mechanisms. Liquid Filling Machine's main transmission components include gears, sprockets, worm gears, screws, and nuts, etc.
Liquid Filling Machine's actuator
Liquid Filling Machine's actuator, this part is mainly to achieve the Liquid Filling Machine packaging process operation and auxiliary operation part, packaging process operation refers to filling, auxiliary operation part refers to packaging materials and products supply and delivery, Liquid Filling Machine packaging material output, etc., the actuator is the core of the machine, its action sequence, and movement law according to the process principle and requirements.
Liquid Filling Machine's control system
The control system of the Liquid Filling Machine is to control the relevant parts of the Liquid Filling Machine, allocate the movements to the actuators, and make them coordinate the movements according to the time and sequence, thus realizing the process functions of the Liquid Filling Machine.
The body part of the Liquid Filling Machine
The body of the Liquid Filling Machine is the skeleton of the Liquid Filling Machine, which mainly plays the role of supporting and positioning the parts. The stability of the body is the first consideration in the design, and the center of gravity of the Liquid Filling Machine should be lowered as much as possible to make the Liquid Filling Machine work smoothly.
The mainframe of Liquid Filling Machine is to fix and support all the working actuators, transmission parts, control systems, to ensure their relative position correctness and stability. The vacuum system of the Liquid Filling Machine sucks the air out of the bottle, thus generating negative pressure inside the bottle, the liquid is filled into the bottle from the liquid tank through the liquid supply system and the filling head, when the liquid reaches the required liquid level, the inlet port is closed and the suction port sucks the excess liquid and foam away.
Liquid Filling Machine of Wenzhou Zungwan Intelligent Machinery Co., Ltd. is first-class product quality and efficient and fast after-sales service, which has created the excellent products of "Zhonghuan". To meet the market demand of Liquid Filling Machine is our eternal topic and sincere commitment to our customers. If you are interested in Liquid Filling Machine, please contact us, our website is www.cnzpack.com. We will carry forward the spirit of "comprehensive innovation, perseverance", self-discipline and strive to be the first, with enthusiasm, new attitude to provide new and old customers with more perfect service. We are looking forward to cooperating with you.
After we purchase Pharmaceutical Filler and Capper, we need to install and debug Pharmaceutical Filler and Capper. Let's take a look at it together next.
This is the content list:
l Installation of Pharmaceutical Filler and Capper
l Commissioning of Pharmaceutical Filler and Capper
l Maintenance of Pharmaceutical Filler and Capper
Installation of Pharmaceutical Filler and Capper
According to different models and specifications of Pharmaceutical Filler and Capper, refer to the random manual for installation.
For small-sized Pharmaceutical Filler and Capper, it is not required to build the foundation, just install it on the flat workshop floor, make a good horizontal reference, adjust the elevation of incoming and outgoing chain belt according to the layout diagram, and adjust the legs to make the load of the whole machine evenly distributed.
For large-sized Pharmaceutical Filler and Capper, it is necessary to build a solid installation foundation as required. When installing, the horizontal benchmark should be played, especially when it is connected with the capping machine, the two parts of the incoming and outgoing bottle belts must be at the same horizontal benchmark.
To ensure the smooth bottle delivery of Pharmaceutical Filler and Capper, the inlet pallet under the inlet star wheel should be 0.5mm higher than the surface of the bottle tray, and the outlet pallet under the middle star wheel should be 0.5mm lower than the surface of the bottle tray. The running is free and there should be no jamming interference. The horizontal part of the liquid inlet pipe should have a certain slope to facilitate emptying and air discharge. Make sure the bearing load of Pharmaceutical Filler and Capper's legs is even. Matching equipment with the host, such as gas-liquid control box, vacuum pump system and electric control box, etc. are generally installed separately.
Commissioning of Pharmaceutical Filler and Capper
After confirming the installation of Pharmaceutical Filler and Capper is completed, the commissioning of Pharmaceutical Filler and Capper can be carried out step by step as follows. Replace suitable accessories according to the bottle type filled by Pharmaceutical Filler and Capper, and adjust the parts, including the inlet screw, guide bar spacing, side guard safety switch, star-shaped paddle wheel, reservoir, and capping head height adjustment, etc. Thoroughly clean the Pharmaceutical Filler and Capper reservoir, liquid piping, and gas piping to ensure that there is no foreign material. Make a hydraulic test on the storage tank and pipeline at the same time. Check carefully whether the wiring of the Pharmaceutical Filler and Capper control box is correct, and turn on the main switch only after the equipment is turned manually without jamming. Start the equipment in a pointing way to check if there is any abnormality. Start the Pharmaceutical Filler and Capper at low speed and check the starting, braking, emergency stop, and speed regulation performance. Then infuse an empty bottle at low speed, check whether it can pass through the bottle feed screw, guide bar, and star wheel smoothly and whether each control touch block can respond sensitively. Check whether the Pharmaceutical Filler and Capper can drop the cap smoothly and seal the cap tightly. After that, adjust the value of each instrument on the liquid and gas control cabinet according to the filing requirements of Pharmaceutical Filler and Capper. Check the liquid level and pressure of Pharmaceutical Filler and Capper reservoir, make filling test, adjust the filling head and control the bottling level.
Maintenance of Pharmaceutical Filler and Capper
Pharmaceutical Filler and Capper in the process of use, must be required to carry out regular maintenance. First of all, we must ensure that the lubrication status of the Pharmaceutical Filler and Capper must be good, and the lubrication points must be well-lubricated in time to maintain the oil level of each tank and the intact spray lubrication function. Timely replacement of a variety of damaged parts, such as seals, bottle transport parts, and transmission parts in the wearing parts. The movable parts that are not adjusted for a long time, such as the reservoir of Pharmaceutical Filler and Capper and the height adjustment device of the capping machine, should be run regularly to avoid rust and corrosion. Regularly and regularly clean the liquid tank of Pharmaceutical Filler and Capper, liquid delivery tube, filling valve, and parts that may contact with liquid as required. Liquid residue, oil, water, and glass fragments should be removed to keep the equipment neat and hygienic. Since there are many models and specifications of Pharmaceutical Filler and Capper, and the performance, structure, and working principle vary greatly, operators and maintenance personnel should use and maintain them according to the operation manuals accompanying each machine.
Our products are in great demand in both domestic and international markets, and we are committed to improving and developing to meet our customers and the market demand is our eternal theme and sincere commitment to our customers. If you are interested in Pharmaceutical Filler and Capper, you can contact us, our website is www.cnzpack.com.
Capping Machine is filling equipment specially designed for new oral liquid easy-pull bottles. The design is reasonable, the structure is simple, the operation is convenient, and a mechanical stop filling device is provided for lack of bottles. So what are the adjustment methods of the Capping Machine? Let's take a look together next.
This is the content list:
l Capping Machine feeding half adjustment
l Matters needing attention in discharging
l Adjustment of the locking device
l Vibrator adjustment
Capping Machine feeding half adjustment
Adjust the bottle blocking plate on the feeding half of the Capping Machine upwards to shorten the adaptation to the bottle feeding stroke. Adjust downwards to make the Capping Machine adapt to the extension of the bottle feeding stroke. Adjust the positioning bottle position left and right to align the bottle position when the movable tooth is running, so that the bottle can be fed into the positioning tooth smoothly. Adjust the bottle blocking plate of the Capping Machine so that the width of the bottle inlet is about 22 mm.
Adjust the perfusion Capping Machine component. The role of the perfusion Capping Machine component is to make the liquid medicine be delivered to each easy-pull bottle in time through the dosing device, one-way valve, and needle. Therefore, the needle must enter the bottle mouth properly and the filling time must be appropriate. Adjust the Capping Machine side cam to rotate clockwise or counterclockwise so that the needle is inserted into the bottle mouth just after the empty bottle enters the toothed position. And lift the needle before leaving the toothed position. The filling time of the Capping Machine is adjusted. Turn the cam clockwise or reverse the adjustable needle into the bottle mouth and start filling immediately, and stop filling before the needle leaves the bottle mouth.
Matters needing attention in discharging
Since the Capping Machine is an easy-pull bottle filling and locking device, the discharging has been capped and sealed. To prevent the locked bottle from overturning, it must be placed on the Capping Machine discharge hopper before the first bottle is discharged. Several empty bottles can be transported to the discharge hopper smoothly to keep the locked bottles and sent to the next process with the bottle hopper.
Adjustment of the locking device
Capping Machine capping time adjustment, adjust the cam rotation angle. When the filling liquid bottle enters the locking tooth position, the locking shaft has moved and left the bottle cap before the moving tooth approaches the bottle. The capping pressure is adjusted, and the capping pressure is adjusted. The size of the cap pressure is directly related to the quality of the lock. If the pressure is too high to break the easy-pull bottle, and the pressure is too small, it will affect the sealing performance. Therefore, the nut should be adjusted according to the actual average height of the easy-pull bottle to adjust the pressure to the best.
Capping Machine blade action time adjustment, the blade should be close to the bottleneck before the end of the capping, otherwise, the locking effect of some short bottles cannot be achieved. Loosen the nut during adjustment, and adjust the shaft and up and down to make the blade action time sooner or later. When adjusting the lock of the Capping Machine, pay attention to the locking of the nuts after the adjustment of each department. The easy-pull bottle must be used for the initial valve test. The average height must be taken. Irregular easy-pull bottles cannot enter the lock to avoid damage to the parts.
Vibrator adjustment
The Capping Machine adopts the principle of electromagnetic oscillation to drop the bottle cap to the proper position along the track according to a certain movement trajectory. The vibrator is packaged separately when it leaves the factory, and the lower rail opening must be aligned with the movement rail of the easy-pull bottle when installed. To adjust the gap between the magnets of the Capping Machine, loosen the screw, open the cover, adjust the nut, and make the vibration of the Capping Machine low and fast.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It strictly controls the production of the Capping Machine. A large number of factory tests are carried out before Capping Machine leaves the factory to ensure product quality. If you are interested in Capping Machine, you can Contact Us, our website is www.cnzpack.com.
Wenzhou Zungwan Intelligent Machine Co.,Ltd. is the professional equipment manufacturer to keep researching and developing the packing machinery for every type of liquid, powder, cream/ointment, fluid and half-fluid etc. materials. We have Obtained ISO9001 quality management system authentication and parts of our products have passed CE authentication. Our company has obtained more than 20 invention patents and utility model patents. The main products range from nail polish filling machine, perfume machine,perfume filling machine, powder serial automatically volume-measuring packing machine and inline capping machine, rotary capping machine and labeling machine, bottle unscrambler , screw capping machine ,tube filling and sealing machine, cartoning machine and other Packaging equipments.
So far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and our service as well as our integrity is acclaimed both in China and abroad. we will carry forward the spirit of "integrated innovation, and perseverance," discipline ourselves to be the first, and provide better and more perfect service for our new and old customers with enthusiasm and a new attitude.
With its extremely high-efficiency performance, the automatic Labeling machine attracts a strong demand of users. Efficiency in the production of modern enterprises has become one of the important indicators that reflect the production capacity of enterprises. The demand for Labeling machines has promoted the progress of science and technology and has become the trend of modern product development. So what are the characteristics and advantages of the fully automatic Labeling machine? Let's take a look together next.
This is the content list:
l Automatic Labeling machine saves a lot of labor costs
l An automatic Labeling machine makes it easy to label goods
l The automatic Labeling machine is extremely efficient and meets the needs of modern enterprises
Automatic Labeling machine saves a lot of labor costs
The automatic Labeling machine saves a lot of labor costs. In the production process of labeling, most of the previous operations were done manually. Manual labeling takes up a lot of labor, the cost is high, and the recruitment and management of personnel are not so easy. The Labeling machine has solved this problem very well. It only needs to train machine operators with certain skills and invest a proper amount of automatic Labeling machines to replace manual labor to complete large-scale and heavy labeling work.
An automatic Labeling machine makes it easy to label goods
The automatic Labeling machine makes it easy to label goods. Manual labeling is difficult to guarantee the quality and effect of labeling. In the modern commodity society, people pay much attention to the appearance and packaging image of products. If the label is of poor quality and unsightly, it will be difficult to attract consumers' desire to buy. The products posted by the Labeling machine are more accurate in position, the surface is very flat, no wrinkles, and the products are more beautiful and generous.
The automatic Labeling machine is extremely efficient and meets the needs of modern enterprises
The automatic Labeling machine is extremely efficient and meets the needs of modern enterprises. With the advancement of technology, the Labeling machine has stronger vitality, higher competitiveness, and superior product labeling efficiency. It can reach thousands or even tens of thousands of labeling times per hour, which is a speed that cannot be imagined by single manpower.
A self-adhesive Labeling machine is relatively semi-automatic labeling or manual labeling. A fully automatic Labeling machine is leading the development direction of self-adhesive Labeling machines with its ultra-high efficiency performance and high-quality labeling effect! For the automatic Labeling machine, it is a big challenge. In the past, the packaging reason was very simple. To solve the quality assurance problem for the product, we did not inject more design factors. Our current packaging equipment not only extends the warranty time but also injects the artistic effect has been achieved so that people can experience the different experience that art brings us in the process of using it. It is impossible to break through the current development model without the help of external forces. We can't predict the direction of automatic Labeling machines, but by making up for the shortcomings of different industries, only the shortcomings can be achieved in a win-win situation, so that all industries can get a benign development. The use of automatic Labeling machines has also reached a new height in the protection of commodities, which just reflects the overall value of commodities. Therefore, the development of automatic Labeling machines is not limited to a small range.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. The company uses the advantages of the Labeling machine to produce a Labeling machine that is more in line with consumer needs. If you are interested in the Labeling machine, you can contact us. Our website is www.cnzpack.com.