











After the Labeling machine sensor sends a signal that the labeling object is ready to be labeled, the drive wheel on the Labeling machine turns up. As the rolled label is in a tight state on the equipment, when the Labeling machine backing paper is tightly attached to the peeling plate and changes direction, the Labeling machine label is forced to disengage due to the rigidity of its material and is ready to be labeled. At this time, the labeling object is located just below the label, under the action of the labeling wheel, to achieve synchronous labeling. After the Labeling machine has finished labeling, the sensor under the roll label sends a stop signal, the drive wheel comes to a standstill, and a labeling cycle end. No matter which type of Labeling machine, the labeling process is roughly the same. The difference is that the installation position of the Labeling machine is different, the labeling object is conveyed differently and positioned differently, and the form of the labeling roller of the Labeling machine is also different. So, what are the Labeling machine's requirements for labels? Let's look at it together next.
This is the content list:
l Surface material
l Release force
l At the end of the paper
l Processing quality
Surface material
Labeling machine label stiffness is the key to labeling, so the Labeling machine surface material is required to have a certain strength and hardness. Labeling machine label stiffness and the thickness of the material and the area of the label, so the Labeling machine in the use of soft film material should be appropriate to increase its thickness, generally controlled at 100μm or more. Labeling machine thin paper materials, such as 60 ~ 70g/m2 labeling paper, are generally not suitable for the production of large labels, but suitable for processing into small labels, such as price tags used on the price tag. Labeling machine label stiffness is not good, it will cause labeling out of the label, or label and backing paper reward so that the automatic labeling failure.
Peel-off force
Labeling machine peel-off force is the force at which the label is separated from the backing paper by the Labeling machine. The Labeling machine release force is related to the type and thickness of the adhesive, the silicone coating on the surface of the backing paper, and the ambient temperature at the time of labeling. If the Labeling machine release force is too small, the label will easily fall off (leave the backing paper) during the conveying process. The Labeling machine's release force is too large, the label will be difficult to detach from the backing paper, and it will not be able to produce labels. The Labeling machine should be integrated control of the technical indicators so that the release force is maintained within a reasonable range.
At the end of the paper
Is also an important indicator to control automatic labeling. The requirements of the Labeling machine base paper surface silicon-coated evenly, the Labeling machine peeling force is consistent. Uniform thickness and good tensile strength ensure that the Labeling machine will not break when labeling. Uniform thickness and good light transmission of the Labeling machine ensure that the sensor can correctly identify the location of the label.
Processing quality
Requires that both sides of the Labeling machine backing paper after slitting should be flat and free of fracture to avoid the backing paper from breaking when the tension changes. Labeling machine die-cutting, to avoid cutting through the backing paper or damage to the silicone layer. If the Labeling machine backing paper and silicone coated layer are destroyed, the Labeling machine backing paper will break easily or the glue in the label will penetrate the backing paper. In addition, the static electricity in the web label must be eliminated before Labeling machine labeling, because static electricity will lead to Labeling machine labeling failure or labeling inaccuracy.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. Before the Labeling machine leaves the factory, it will conduct a large number of tests on the Labeling machine to maintain the healthy development of the Labeling machine market. If you are interested in the Labeling machine, you can contact us, our website is www.cnzpack.com.
Cartoning machine is the description of automatic loading of medicine bottles, trays, ointments, etc. into folded cartons and completing the capping action. Some Cartoning machines with stronger functions also have functions such as sealing labels or heat shrink packaging. So what are the considerations for the daily maintenance of the Cartoning machine? Let's take a look together next.
This is the content list:
l Comply with safe operating procedures
l Refuel or change the oil on time
l Be organized
l Clean inside and outside of equipment
Comply with safe operating procedures
Comply with the Cartoning machine's safety operating procedures and do not overload the equipment. The Cartoning machine's safety protection devices are complete and reliable, and unsafe factors are eliminated in time. For example: Do not touch the inverter within 5 minutes after the power of the Cartoning machine is cut off because it will have a relatively high residual voltage, which will be released after a few minutes. After the Cartoning machine work is finished, you should do a good job of cleaning, use a brush to remove all unclean things, and check whether the power is turned off.
Refuel or change the oil on time
Cartoning machine is well lubricated, add oil or change oil on time, keep oiling, no dry friction. The Cartoning machine should be refueled before starting up. Where there is reciprocating motion, add oil, twice a day, 5-6 drops each time. Add butter once a month to the bearings of the rotating part on both sides of the folding machine. Grease the sliding part of the tongue guide once a week.
Be organized
Cartoning machine tools, accessories, and workpieces (products) should be neatly arranged, Cartoning machine pipes and lines should be organized.
Equipment interior and exterior clean
The interior and exterior of the Cartoning machine equipment should be clean and tidy. All sliding surfaces, lead screws, rack and pinion, gearbox, oil holes, etc. are free of oil and dirt, and all parts of the Cartoning machine do not leak oil or air. The debris, debris, and dirt around the equipment should be cleaned up. For example, there should be no foreign objects in the main motor of the Cartoning machine, the casing should be kept clean, the cooling fan should be good, and it should be maintained regularly. Cartoning machine photoelectric switch and proximity switch detection surface should not have foreign matter and pollution, otherwise, it will cause malfunction. The detection distance should be properly adjusted, and the bracket should be kept tight and not loose to avoid damage when the machine is running. The electrical components inside and outside the electrical cabinet of the Cartoning machine must be kept clean and well dissipated.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It will test the Cartoning machine before leaving the factory and provide warranty service. If you are interested in Cartoning machine, you can contact us. Our website is www.cnzpack.com. I look forward to your coming and hope to cooperate with you.
In our production and life, the unscrambler has an important influence on us. So what are the types of Bottle Unscrambler? Let's take a look together next.
This is the content list:
l Gravity Bottle Unscrambler
l Water-floating and baffled Bottle Unscrambler
l Friction Bottle Unscrambler
l Centrifugal Bottle Unscrambler
Gravity Bottle Unscrambler
The basic principle of the gravity-centered Bottle Unscrambler is to use the characteristics of the division of the bottle's center of gravity during the finishing process. If the bottle is facing forward, the center of gravity of the Bottle Unscrambler will be close to the bottom of the bottle, so that the bottle will not change its arrangement. If the bottle is reversed, the center of gravity will be at the upper part of the bottle, the center of gravity of the bottle will be unstable, this function is suitable for use in the Bottle Unscrambler, which is a heavy glass bottle.
Water-floating and baffled Bottle Unscrambler
The basic principle of the water-floating and baffled Bottle Unscrambler is to use the buoyancy principle of water in the conveying stage to convey the bottles to the finishing stage. In the Bottle Unscrambler finishing stage, baffle A is used to make the bottles forward. There is a rectangular cavity on the baffle that fits the bottle mouth. When the bottle mouth of the Bottle Unscrambler comes over, the mouth of the bottle will enter the rectangular cavity, so that the bottom of the bottle is lowered first, and the mouth of the bottle is lowered, and the bottle will be output in the forward direction. When the bottom comes over, the baffle does not work, and the Bottle Unscrambler bottle is output in the forward direction.
Friction Bottle Unscrambler
The basic principle of the friction Bottle Unscrambler is to use the friction of the belt to transport the bottles in the finishing stage, and to adjust the bottles by the friction in the finishing stage. Compared with the above two schemes, this scheme has the advantage of high-efficiency Z, and there are no other unnecessary processes, such as cleaning phases. The structure design of the Bottle Unscrambler mainly utilizes the friction of the belt, and the friction type Bottle Unscrambler enables the bottle to flip under high-speed movement, and achieves high efficiency, and improves processing efficiency.
Centrifugal Bottle Unscrambler
The basic principle of the centrifugal Bottle Unscramble is to use the centrifugal force of the disc to bring the bottle close to the outside of the ring, and then use the different characteristics of the bottom and the width of the bottle mouth to turn the bottle mouth downwards. The function of the centrifugal Bottle Unscrambler is to manually add materials to the storage bottle library for storage. The materials in the storage bottle library will be automatically quantified and fed to the turntable at a set speed. The turntable rotates at a high speed to supply the bottles as required. The web wheel the irregular bottles are removed, and the bottle dividing part sends the bottles from the turntable to the bottle unscramble part at a certain speed. The unscrambler part clamps the bottles to the working surface of the conveyor through the conveyor belts on both sides, and at the same time sorts out the bottles through the bottle turning device. It is an indispensable machine for high-speed production to realize fully automated operation, and it saves a lot of labor costs and avoids losses caused by human error factors.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer with good development in the quality of Bottle Unscrambler products. If you are interested in Bottle Unscrambler, you can contact us. Our website is www.cnzpack.com.
In our production and life, the Liquid Filling Machine has a significant impact on many industries, so what is the method of using the Liquid Filling Machine? Let's go take a look next.
This is the content list:
l The ground wire must be well-grounded before the Liquid Filling Machine works
l Liquid Filling Machine liquid filling system assembly
The ground wire must be well-grounded before the Liquid Filling Machine works.
The ground wire must be well-grounded before the Liquid Filling Machine works, and then the appropriate standard syringe must be selected according to the different filling volumes. Generally, a 1ml syringe is used when the dispensing range is 0.2-1ml. Use a 5ml syringe for 1-5ml.use a 10ml syringe for 5-10ml. The 20ml model uses a 20ml glass infusion device. The 100ml model uses a 100ml glass infusion device, and the 500ml model uses the stainless steel filling system produced by our factory.
Liquid Filling Machine liquid filling system assembly
Pull out the inner core of the Liquid Filling Machine syringe, put the screw sleeve on the inner core of the syringe, and use the screw sleeve to properly fasten it to the lower base (cleanliness must be paid when disassembling the syringe). Place the upper clamp seat on the outlet end of the Liquid Filling Machine syringe jacket, and properly tighten the nuts on both sides to assemble the inner core and outer jacket of the installed Liquid Filling Machine syringe into one body. At this point, the Liquid Filling Machine injection system is assembled.
Place the Liquid Filling Machine valve with the arrow facing upwards and the arrow mark facing outwards and fix it on the fixing screw with a nut. Assemble the Liquid Filling Machine with a complete liquid filling system, align the upper and lower round holes of the liquid filling system components with the upper and lower fixing rods respectively, and put them on the bearing so that the outer end surface and the bearing surface are levels. When assembling the lower end, do not make the screw sleeve and the crank touch to prevent abnormal noise when the crank on the Liquid Filling Machine rotates (the screw sleeve and the crank are about 1mm apart when installed correctly). After the liquid filling system is installed correctly, tighten it. Tighten the screws up and down. Use a short hose to connect the Liquid Filling Machine syringe to the valve connection nozzle. The liquid inlet pipe is connected to the water inlet, and the liquid outlet pipe is connected to the water outlet. To prevent the liquid inlet and outlet pipes from being entangled, clip the liquid inlet and outlet pipes into the ear openings on the side of the casing.
Turn the crank of the Liquid Filling Machine by hand, it should be able to rotate freely, otherwise, the assembly is wrong, you should check whether the Liquid Filling Machine injection system is fastened to the rotating bearing.
Our company has obtained more than 20 invention patents and utility model patents. The main products are a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and online capping machine, capping machine and labeling machine, bottle unscrambler, tube filling and sealing machine, Cartoning machines, and other packaging equipment. If you are interested in Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.
Tube Filling machine And Sealing machine adopt the latest module circuit, stable working performance, high efficiency, and all components adopt famous brand products. Under the careful design of our company, various advanced Tube Filling Machine And Sealing machines have been produced. Mainly used for sealing toothpaste, cosmetics, medicine, food, industrial products, and various hoses. Next, let's take a look at the cleaning and maintenance of the Tube Filling machine And Sealing machine. Here are some answers.
Here is the content list:
Tube Filling machine And Sealing machine cleaning.
Daily maintenance of Tube Filling machine And Sealing machine.
First, regularly clean the surface of the Tube Filling machine And Sealing machine, the bottom plate and the lower mold slide plate, grooves, the upper mold inner pressure plate, and the positioning rod. Second, grease should be added to the transmission parts of the lower mold slide plate, pressing rod bearing, eccentric wheel and guidepost, guide rail, and so on regularly to ensure the performance of the Tube Filling Machine And Sealing machine. Third, the method of cleaning the toothed knife: first plug the two drain holes of the lower mold with a cotton ball, pour boiling water into the groove of the lower mold, until it is full, then push the slide of the lower mold into place, and lower the upper mold. Press to the lowest point, let the toothed knife soak for a few minutes until it is clean, repeat several times.
First, check the equipment ground wire frequently to ensure reliable contact; clean the weighing platform frequently; check whether the pneumatic pipeline is leaking and whether the air pipe is broken. Second, change the lubricating oil of the reducer motor every year, check the tightness of the chain, and adjust the tension in time. Third, the sensor of the Tube Filling Machine And Sealing machine is a high-precision, high-sealing, and high-sensitivity device. Impact and overload are strictly prohibited, and no contact is allowed during the working process, and it is not allowed to be disassembled if it is not required for maintenance. Fourth, if it is not used for a long time, empty the material in the pipeline. Fifth, observe the moisture filter and oil mist device of the pneumatic combination two-piece before going to work every day. Sixth, during the production, we should always patrol and observe the mechanical parts to see if the rotation and lifting are normal if there is any abnormality, and if the screws are loose. Seventh, do a good job of cleaning and sanitation, keep the surface of the Tube Filling machine And Sealing machine clean, often remove the accumulation on the scale body, and pay attention to keeping the electric control cabinet clean.
Wenzhou Zungwan Intelligent Machine Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream, ointment, fluid, and semi-fluid materials. If you are engaged in work related to Tube Filling machine And Sealing machine or want to know more about our company, you can contact us. Our official website is https:// www.cnzpack.com/.
Korea East Asia Pharmaceutical Company, ordered a syrup filling line from our company, from bottle management - bottle washing - filling - corking - capping - labeling, the whole line in the Korean factory to complete the commissioning task, the whole line production design speed of 120 bottles per minute high-speed filling line.
The Cosmetic Filling machine And Capping machine has a wide range of applications, not only in the cosmetics industry but also in food, daily chemical, pharmaceutical, and other industries. It is very flexible to use, can be adapted to different bottle mouths, and the operation is relatively simple and quick. Because of its unique advantages, it has won unanimous praise from customers. Next, let's take a look at the advantages, characteristics, and manufacturer introduction of Cosmetic Filling machines And Capping Machines. Here are some answers.
Here is the content list:
l Advantages of Cosmetic Filling machine And Capping machine.
l The performance characteristics of Cosmetic Filling machine And Capping machine.
l Introduction of Cosmetic Filling machine And Capping machine manufacturer.
Advantages of Cosmetic Filling machine And Capping machine.
Cosmetic Filling Machine And Capping machine integrates mechanical, pneumatic, and automatic. The characteristics of a high degree of automation, high output, wide application, and good stability make this machine more popular. The Cosmetic Filling machine And Capping machine can automatically unscramble bottles, fill, seal, cap, and label. Equipped with an automatic internal plug-in row and external cover plug test, it can realize no internal plug and non-external plug and eliminate the non-external plug. The labeling adopts a belt rolling structure, a fast-rolling structure, and an 8-dimensional angle adjustment label to realize the labeling of two symmetrical labels or high-precision labeling.
The performance characteristics of Cosmetic Filling machine And Capping machine.
First, the man-machine interface setting, intuitive and convenient operation, PLC control, accurate loading. Frequency conversion control, arbitrary adjustment of production speed, automatic counting. Second, the Cosmetic Filling machine And Capping machine is made of stainless steel, which meets GMP requirements. Third, the equipment fully complies with GMP requirements. Microcomputer setting, accurate filling volume, convenient operation, automatic shutdown function, automatic shutdown for any track with continuous no filling and no internal clogging. Fourth, the Cosmetic Filling machine And Capping machine is easy to operate and easy to maintain.
Introduction of Cosmetic Filling machine And Capping machine manufacturer.
Wenzhou Zungwan Intelligent Machine Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream, ointment, fluid, and semi-fluid materials. We have obtained ISO9001 quality management system certification, and some products have passed CE certification. Our company has obtained more than 20 invention patents and utility model patents. The quality of our Cosmetic Filling Machine And Capping machine and service as well as our integrity are widely praised at home and abroad.
The first-class quality of Cosmetic Filling machine And Capping machine and efficient and fast after-sales service have created the excellent products of "Zhonghuan". Cosmetic Filling Machine And Capping machine is in great demand in domestic and foreign markets. Keep improving, develop to satisfy customers, and satisfy market demands are our eternal topic and our sincere commitment to customers.
Our official website is https:// www.cnzpack.com/. If you are engaged in work related to Cosmetic Filling machines And Capping machines or want to learn more about our company, you can communicate with us on the website. We wholeheartedly provide users with better products and services!
Speaking of Bag packaging machines for large machinery, it is necessary to briefly talk about the knowledge of stand-up pouches. Bag packaging machines in the application, development, and growth of stand-up pouches played a role in what? Let's look at it together next.
This is the list of contents:
Stand-up pouches in brief
The basic classification of stand-up pouches
Stand-up pouches produced by Bag packaging machines are flexible packaging bags with a horizontal support structure at the bottom. It does not rely on any support, whether the bag is opened or not, it can stand on its own. Since its appearance and promotion, stand-up pouches have been very popular. With their good design and function, they have been widely used in food, daily necessities, pharmaceuticals, and other fields. Stand-up pouches produced by Bag packaging machines are mainly used for juice drinks, sports drinks, spices, and other products. In addition to the food industry, the application of some Bag packaging machine products such as detergents, daily cosmetics, pharmaceuticals, etc. is gradually increasing.
The basic classification of stand-up pouches
1. Ordinary stand-up pouches
That is, the general form of the Bag packaging machine produced by the stand-up pouches in the form of four seals, cannot be resealed and reopened. This stand-up pouch packaging machine to produce stand-up pouches is generally used in the industrial supplies industry.
2. Stand-up pouches with suction nozzles
Stand-up pouches with suction nozzles produced by the Bag packaging machine are more convenient to pour or suck out the contents and can be re-closed and re-opened at the same time. It can be thought of as a combination of stand-up pouches and ordinary bottle spout.
3. Stand-up pouches with zipper
Stand-up pouches with zippers produced by the Bag packaging machine can also be re-closed and re-opened. As the zipper produced by the Bag packaging machine is not closed, the seal strength is limited, so this form is not suitable for packaging liquids and volatile substances.
4. Special-shaped stand-up pouches
That is, according to the packaging needs, based on the traditional packaging bags, change the Bag packaging machine production of a variety of new shapes of stand-up pouches, such as waist design, bottom deformation design, handle design, etc.
Bag packaging machine production of stand-up pouches not only improves the product grade, but also strengthens the visual effect of the shelf, and is easy to carry, easy to use, with good preservation and sealing performance. The development of stand-up pouches produced by the Bag packaging machine, but also the packaging machinery industry to follow the trend, the development of adaptable Bag packaging machine.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops a wide range of packaging machinery for liquid, powder, cream/paste, fluid, and semi-fluid materials. We have obtained ISO9001 quality management system certification and some of our products have passed CE certification. Our company has obtained more than 20 invention patents and utility model patents. Our main products include a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and in-line capping machine, capping machine and labeling machine, bottle management machine, tube filling and sealing machine, cartooning machine, and other packaging equipment. If you are interested in a Bag packaging machine, you can contact us, our website is www.cnzpack.com.