











Pharmaceutical Filler and Capper, whether semi-automatic or fully automatic, will encounter more or less in the process of using different places of failure, in the face of Pharmaceutical Filler and Capper's special parts of the failure, how do we find the problem as soon as possible and solve it? Let's take a look at it.
This is the content list:
l Pharmaceutical Filler and Capper's PLC failure
l Pharmaceutical Filler and Capper's Magnetic Switch Failure
l Pharmaceutical Filler and Capper solenoid valve failure
Pharmaceutical Filler and Capper PLC Failure
If the point controls Pharmaceutical Filler and Capper, the fault phenomenon is that the motor runs after the signal start Pharmaceutical Filler and Capper, but the motor does not stop running after the stop signal is issued. And Capper only stops running when the PLC is powered down. If the point controls the solenoid valve. The fault phenomenon is that the solenoid valve coil is not energized, and the cylinder is not reset. If the PLC of Pharmaceutical Filler and Capper is hit with external force to make the sticking point separate, it can assist to determine the fault of Pharmaceutical Filler and Capper.
Pharmaceutical Filler and Capper's magnetic switch failure
Pharmaceutical Filler and Capper's magnetic switch is used to detecting the position of the cylinder and control the cylinder travel. The four cylinders of laminating, pushing, pressing, and fusing knife are interrelated, and the magnetic switch is used to detect and control their positions. Pharmaceutical Filler and Capper failure is mainly manifested as the subsequent cylinders do not move, because the cylinder speed of Pharmaceutical Filler and Capper is faster, which causes the magnetic switch cannot detect the signal. Such as pushing the package cylinder speed is too fast, after pushing the package reset, the pressure package and fusion knife cylinder do not move.
Solenoid valve failure of Pharmaceutical Filler and Capper
Pharmaceutical Filler and Capper solenoid valve failure is mainly manifested as the cylinder does not move or does not reset, the reason is that Pharmaceutical Filler and Capper cylinder solenoid valve cannot change direction or tampering air. If the solenoid valve falters, the air pressure of Pharmaceutical Filler and Capper can't reach the working pressure because the inlet and outlet air paths are connected, and the knife beam doesn't rise to the place. the proximity switch of Pharmaceutical Filler and Capper knife beam protection doesn't work, and the precondition of full machine operation is not established. Pharmaceutical Filler and Capper does not operate, which is easily confused with an electrical fault. Solenoid valve air leakage sound, listen carefully to the source of sound and hand search for air leakage points, generally can easily identify the air leakage solenoid valve.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, with first-class product quality and efficient and fast after-sales service, forging the excellent products of "Central". Pharmaceutical Filler and Capper will undergo a lot of product testing before leaving the factory to reduce the probability of failure of Pharmaceutical Filler and Capper, and also provide customers with high-quality Pharmaceutical Filler and Capper warranty service. If you are interested in Pharmaceutical Filler and Capper, you can contact us, our website is www.cnzpack.com.
Wenzhou Zungwan Intelligent Machine Co.,Ltd. is the professional equipment manufacturer to keep researching and developing the packing machinery for every type of liquid, powder, cream/ointment, fluid and half-fluid etc. materials. We have Obtained ISO9001 quality management system authentication and parts of our products have passed CE authentication. Our company has obtained more than 20 invention patents and utility model patents. The main products range from nail polish filling machine, perfume machine,perfume filling machine, powder serial automatically volume-measuring packing machine and inline capping machine, rotary capping machine and labeling machine, bottle unscrambler , screw capping machine ,tube filling and sealing machine, cartoning machine and other Packaging equipments.
So far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and our service as well as our integrity is acclaimed both in China and abroad. we will carry forward the spirit of "integrated innovation, and perseverance," discipline ourselves to be the first, and provide better and more perfect service for our new and old customers with enthusiasm and a new attitude.
The tube Filling machine And the Sealing machine are determined by multiple parameters. It is impossible to describe a Tube Filling machine And Sealing machine with any single parameter. Shaft power, blade displacement, pressure head, blade diameter, and filling speed are the five basic parameters that describe a Tube Filling Machine And Sealing machine. So, let's take a look at the principle of the Tube Filling machine And Sealing machine together. Here are some answers.
Here is the content list:
l Basic parameters.
l The shear rate of the fluid.
l Small slot and big slot.
Basic parameters.
The displacement of the blade is proportional to the flow rate of the blade itself, the first power of the blade speed, and the third power of the blade diameter. The shaft power consumed by the filling is proportional to the specific gravity of the fluid, the power standard of the blade itself, the third power of the speed, and the fifth power of the blade diameter. In the case of a certain power and blade form, the blade displacement and pressure head can be adjusted by changing the diameter of the blade and the matching of the speed. That is, the large diameter blade is equipped with a low-speed Tube Filling machine And a Sealing machine. High flow effect and low-pressure head, while the small diameter blade with high speed produces a higher pressure head and lower flow effect.
The shear rate of the fluid.
In the filling tank, the only way to make the micelles collide with each other is to provide a sufficient shear rate. According to the mechanism of the Tube Filling Machine And Sealing machine, it is because of the existence of fluid velocity difference that the fluid layers are mixed. Therefore, where the filling process always involves the fluid shear rate lhhaha620. Shear stress is a force that is the real cause of bubble dispersion and droplet breaking in filling applications. It must be pointed out that the shear rate at each point of the fluid in the entire stirred tank is not the same.
Small slot and big slot.
Experimental research shows that, as far as the blade area is concerned, no matter what type of blade, when the diameter of the blade is constant, the maximum shear rate and the average shear rate increase with the increase of the speed. However, when the rotation speed is constant, the relationship between the maximum shear rate and the average shear rate, and the diameter of the blade is related to the slurry type. When the rotation speed is constant, the maximum shear rate of the radial blade increases with the increase of the blade diameter, and the average shear rate has nothing to do with the diameter of the blade. These concepts about the shear rate of the blade area require special care in the design of the Tube Filling Machine And Sealing machine to reduce and enlarge. Because the small groove is compared with the large groove, the small groove Tube Filling Machine and Sealing machine often has the characteristics of high speed, small blade diameter, and low tip speed. The large groove Tube Filling Machine And Sealing machine often has the characteristics of low speed, large blade diameter, and high tip speed.
Our official website is https:// www.cnzpack.com/. If you are engaged in work related to the Tube Filling machine And Sealing machine, you can communicate with us on the website.
Pharmaceutical Filler and Capper have been used by more and more companies in the industry, and many operators have learned how to use Pharmaceutical Filler and Capper, but they do not know much about its properties and working principle, so when Pharmaceutical Filler and Capper malfunctions, there is no way to start. So what is the working principle of Pharmaceutical Filler and Capper? Let's take a look at it.
This is the content list:
l Introduction of Pharmaceutical Filler and Capper
l Pharmaceutical Filler and Capper working principle
Introduction of Pharmaceutical Filler and Capper
Pharmaceutical Filler and Capper is a machine for filling and sealing objects, which is a small product in the packaging machine and is divided into the semi-automatic filling machine and fully automatic filling line in terms of the degree of automation of Pharmaceutical Filler and Capper production. From the point of view of packaging materials can be divided into liquid filling machinery, paste filling machine, powder filling machine, granule filling machine. Recently, with the QS certification of food, many manufacturers have started to focus on the quality and packaging of Pharmaceutical Filler and Capper.
Pharmaceutical Filler and Capper working principle
For Pharmaceutical Filler and Capper to achieve the linkage effect, it is driven by transmission machinery, so that all parts can work in coordination. When Pharmaceutical Filler and Capper reaches a certain number of bottles, there is a special infrared sensor on the inlet track to receive the induction, which automatically catches the bottles behind and allows the bottles in front to be filled. After the bottles are filled, then let the bottles behind enter to fill the space, to realize no bottle without filling. When the bottles enter the position under the filling head, the other working sections stop and only the filling headworks, when the bottles leave, the Pharmaceutical Filler and Capper's head stops working, the track section works and the bottle stopper is released. The clean bottles coming out of the bottle washer are fed into the inlet spiral of Pharmaceutical Filler and Capper by the bottle feeding belt and sent to the bottle-holding cylinder on the rotary table through the bottle feeding star wheel and raised, the bottle mouth is guided by the centering device and pressed against the lower part of the filling valve to form a seal. After being evacuated, the backpressure gas (CO,) in the storage cylinder is rushed into the bottle, when the gas pressure in the bottle is equal to the gas pressure in the storage cylinder, the liquid valve opens under the action of the liquid valve spring, at this time, the object is automatically filled into the glass bottle along the bottle wall through the guidance of the umbrella type reflective ring on the return tube and is replaced into the storage cylinder through the return tube, when the object rises to a certain height and closes the return tube mouth. Automatically stop down the object. Then the liquid valve and gas valve are closed to drain the pressure gas in the neck part of the bottle to prevent the gushing of the object with gas when the glass bottle is descending so that the whole filling process is completed This is the main working principle of Pharmaceutical Filler and Capper, and the users can use it according to these Users can know clearly which part of the machine has problems and repair them according to these features of Pharmaceutical Filler and Capper.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, constantly researching and developing packaging machinery for various materials such as liquid, powder, cream/oil, fluid, and semi-fluid. Extensive tests are conducted before the Pharmaceutical Filler and Capper leave the factory to ensure the quality of products and maintain the healthy development of the Pharmaceutical Filler and Capper market. If you are interested in Pharmaceutical Filler and Capper, you can contact us at www.cnzpack.com. You are very welcome and we look forward to working with you.
Capping Machine is filling equipment specially designed for new oral liquid easy-pull bottles. The design is reasonable, the structure is simple, the operation is convenient, and a mechanical stop filling device is provided for lack of bottles. So what are the adjustment methods of the Capping Machine? Let's take a look together next.
This is the content list:
l Capping Machine feeding half adjustment
l Matters needing attention in discharging
l Adjustment of the locking device
l Vibrator adjustment
Capping Machine feeding half adjustment
Adjust the bottle blocking plate on the feeding half of the Capping Machine upwards to shorten the adaptation to the bottle feeding stroke. Adjust downwards to make the Capping Machine adapt to the extension of the bottle feeding stroke. Adjust the positioning bottle position left and right to align the bottle position when the movable tooth is running, so that the bottle can be fed into the positioning tooth smoothly. Adjust the bottle blocking plate of the Capping Machine so that the width of the bottle inlet is about 22 mm.
Adjust the perfusion Capping Machine component. The role of the perfusion Capping Machine component is to make the liquid medicine be delivered to each easy-pull bottle in time through the dosing device, one-way valve, and needle. Therefore, the needle must enter the bottle mouth properly and the filling time must be appropriate. Adjust the Capping Machine side cam to rotate clockwise or counterclockwise so that the needle is inserted into the bottle mouth just after the empty bottle enters the toothed position. And lift the needle before leaving the toothed position. The filling time of the Capping Machine is adjusted. Turn the cam clockwise or reverse the adjustable needle into the bottle mouth and start filling immediately, and stop filling before the needle leaves the bottle mouth.
Matters needing attention in discharging
Since the Capping Machine is an easy-pull bottle filling and locking device, the discharging has been capped and sealed. To prevent the locked bottle from overturning, it must be placed on the Capping Machine discharge hopper before the first bottle is discharged. Several empty bottles can be transported to the discharge hopper smoothly to keep the locked bottles and sent to the next process with the bottle hopper.
Adjustment of the locking device
Capping Machine capping time adjustment, adjust the cam rotation angle. When the filling liquid bottle enters the locking tooth position, the locking shaft has moved and left the bottle cap before the moving tooth approaches the bottle. The capping pressure is adjusted, and the capping pressure is adjusted. The size of the cap pressure is directly related to the quality of the lock. If the pressure is too high to break the easy-pull bottle, and the pressure is too small, it will affect the sealing performance. Therefore, the nut should be adjusted according to the actual average height of the easy-pull bottle to adjust the pressure to the best.
Capping Machine blade action time adjustment, the blade should be close to the bottleneck before the end of the capping, otherwise, the locking effect of some short bottles cannot be achieved. Loosen the nut during adjustment, and adjust the shaft and up and down to make the blade action time sooner or later. When adjusting the lock of the Capping Machine, pay attention to the locking of the nuts after the adjustment of each department. The easy-pull bottle must be used for the initial valve test. The average height must be taken. Irregular easy-pull bottles cannot enter the lock to avoid damage to the parts.
Vibrator adjustment
The Capping Machine adopts the principle of electromagnetic oscillation to drop the bottle cap to the proper position along the track according to a certain movement trajectory. The vibrator is packaged separately when it leaves the factory, and the lower rail opening must be aligned with the movement rail of the easy-pull bottle when installed. To adjust the gap between the magnets of the Capping Machine, loosen the screw, open the cover, adjust the nut, and make the vibration of the Capping Machine low and fast.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It strictly controls the production of the Capping Machine. A large number of factory tests are carried out before Capping Machine leaves the factory to ensure product quality. If you are interested in Capping Machine, you can Contact Us, our website is www.cnzpack.com.
In our daily life, Capping Machine plays a vital role for us, so what are the main work processes and precautions of the Capping Machine? Let's take a look together next.
This is the content list:
The main workflow of Capping Machine
How to carry out daily maintenance and maintenance of Capping Machine
How to deal with common problems of Capping Machine
We know that after the plastic bottles are sorted by the Capping Machine, they enter the conveyor chain in a single row. In the filling station, the plunger pump injects the liquid in the container into the plastic bottle. After filling, the plastic bottle enters the index plate and stops accurately at the capping station. Manually place the cap of the Capping Machine at the entrance of the friction beltline, take out the capping claw, screw the cap claw, and squeeze the tube claw to complete the capping action. Then the plastic bottle exits the index plate and enters the conveyor chain, and enters the labeling station to complete the round bottle labeling.
1. Always keep the Capping Machine clean, especially for the electrical appliances on the switchboard, to prevent moisture and dust, and it is forbidden to change the program of the inverter and the program controller at will.
2. The power supply voltage of the Capping Machine should be stable, not exceeding ±15%, the material temperature should be kept at 10℃-40℃, the ambient temperature should be kept at 5℃~40℃, and the temperature should be kept at 5~95%PH.
3. The flowmeter used by the Capping Machine for spray filling is a precision instrument. Therefore, the oil must be precision filtered before it can be filled.
4. Turn off the power supply and oil inlet valve of the Capping Machine after finishing the work.
5. Pay attention to the cleanliness of the infrared sensor from the Capping Machine. Frequently wipe it clean with clean cotton. It is strictly forbidden for any object to approach the sensor during the working process, and strong light should not be directly or reflected on the sensor, otherwise, it will prosper and malfunction.
6. Add cylinder lubricating oil to the pneumatic triplet regularly.
7. When the machine is not used for a long time, all parts should be wiped clean and covered with plastic or tarpaulin to prevent dust.
First, what should I do if the cylinder piston of the Capping Machine does not work? Confirm whether the safety emergency stop switch is safe. Confirm that the air supply switch of the Capping Machine is turned on. Check if the Capping Machine one-way signal valve is damaged.
Second, what should I do if the Capping Machine cylinder piston does not return after being pushed to the top? Confirm whether the moving target is in contact with the one-way valve.
Third, how to adjust the filling volume of the Capping Machine is inaccurate or not discharged?
Check whether the upper and lower throttle valves of the Capping Machine are closed, and increase the pumping speed of the throttle valve of the cylinder. Make sure that the Capping Machine quick-install tee is locked with a clamp. Confirm whether there are enough materials in the Capping Machine storage box. Make sure that the joints of the pipes of the Capping Machine are sealed.
Fourth, what should I do if the material of the Capping Machine flows out from the rear end of the cylinder? Check whether the sealing ring on the Capping Machine piston is worn. If it is worn, replace it and make sure that the piston and the piston rod are tight.
In addition to timely handling of problems, it is also necessary to do a good job of preventive work in advance. Doing a good job in daily maintenance can also reduce the failure rate of the Capping Machine. The daily maintenance and maintenance of the Capping Machine cannot be underestimated. This is a very important step. Daily maintenance on time can effectively extend the service life of the Capping Machine, improve the production efficiency of the enterprise, and keep Capping Machine in normal operation throughout the day, reducing manpower. The loss of material resources.
Wenzhou Zungwan Intelligent Machinery Co., Ltd.'s first-class product quality and efficient and quick after-sales service have created excellent products of "Zhonghuan". Products are in great demand in the domestic and foreign markets. Keep improving, develop to satisfy customers, and meet market demands are our eternal topic and our sincere commitment to customers. Therefore, Capping Machine is very popular among consumers. If you are interested in Capping Machine, you can contact us. Our website is www.cnzpack.com.
There is already a lot of knowledge about the Labeling Machine in the market, but the Labeling Machine will appear crooked in the process of using it. How should this be solved? Let's take a look together next.
This is the content list:
Reasons for Labeling Machine crooked during use
Labeling Machine appears to "post crooked" solution
Why does Labeling Machine post crookedly during use? There are two factors: one is running in an environment that is not suitable for Labeling Machine work, and the other is the lack of maintenance of Labeling Machine equipment. The round Labeling Machine adopts self-adhesive roll labeling paper, and the labeling adopts the rolling method to complete the labeling process. The self-adhesive Labeling Machine is clean and hygienic, non-mold, beautiful, and firm after labeling, and will not fall off by itself, and production efficiency Higher merits. If you can do both of these things, you can eliminate the problem of inaccurate labeling.
First, stop the Labeling Machine, and then inspect whether the labeling heads on both sides of the Labeling Machine are loose. Use the tools configured by the manufacturer to stabilize the Labeling Machine. Check whether the Labeling Machine wraps the label's trays for looseness or uneven rotation speed. Add engine oil to lubricate. Round bottle Labeling Machine realizes labeling or filming on the circumferential surface of cylindrical and conical products, such as glass bottles, plastic bottles, etc. It can realize circumferential, semicircular, circumferential double-sided, circumferential positioning labeling and other functions, mainly vertical There are two ways of labeling and horizontal labeling. Then inspect the parameters of the Labeling Machine operating system to avoid labeling different products under the same parameters of the Labeling Machine. Finally, adjust the labeling head and place the labeling product separately. When the conveyor belt is conveyed, whether the Labeling Machine shakes or shakes the first two These steps must be performed after the Labeling Machine stops. If the above two cannot solve the labeling problem of the Labeling Machine, please do not disassemble and replace the internal parts of the device privately. You need to transfer the professional to repair the Labeling Machine.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. So far, we have more than 100 domestic customers and more than 400 foreign customers. The quality of our Labeling Machine and service as well as our integrity are widely praised at home and abroad. We will carry forward the spirit of "comprehensive innovation and perseverance", self-discipline and strive for the first place, and provide new and old customers with better and more complete services with enthusiasm and a new attitude. It can be seen that we have developed well in the quality of Labeling Machine products. Labeling Machine's first-class product quality and efficient and fast after-sales service have created excellent products of "Zhonghuan". If you are interested in Labeling Machine, you can contact us, our website is www.cnzpack.com. I look forward to your coming and hope to cooperate with you.
With the increasingly fierce competition in the manufacturing and production of plastic bottles in the food and pharmaceutical industries, Bottle Unscrambler has become more and more solid backing for the food and pharmaceutical plastic bottle markets. So how does it play a role? We will introduce the work process and personnel operation specifications of Bottle Unscrambler. Let's take a look together next.
This is the content list:
The workflow of Bottle Unscrambler
Personnel operation specification of Bottle Unscrambler
The workflow of Bottle Unscrambler is generally as follows: manually put materials into the storage bottle library, the materials in the storage bottle library will be automatically quantified and fed to the turntable at the set speed. The turntable rotates at a high speed to supply the bottles as required, the web wheel The irregular bottles are removed, and the bottle dividing part sends the bottles from the turntable to the bottle unscramble part at a certain speed. The Bottle Unscrambler part of the Bottle Unscrambler clamps the bottles to the working surface of the conveyor through the conveyor belts on both sides, and at the same time sorts the bottles through the bottle turner. The Bottle Unscrambler electronic control system performs real-time monitoring and feedback through the sensors of each part to achieve fully automated operation requirements, and save a lot of labor costs and avoid losses caused by human error factors.
To ensure the normal and safe operation of Bottle Unscrambler, there are special operating procedures established for it. Operators and equipment management personnel shall perform standardized operations of Bottle Unscrambler under these procedures. This safe operation specification is commonly used in Bottle Unscramblers, mixers, high-speed automatic Bottle Unscramblers, etc.
1. First check the Bottle Unscrambler's intact, clean, and expiration status identification and the equipment operation record of the shift. If the inspection finds that the Bottle Unscrambler has exceeded the cleaning validity period, it is necessary to further clean the equipment according to the equipment cleaning operation rules and fill in the equipment status identification.
2. Check the Bottle Unscrambler and the Bottle Unscrambler to confirm that there is no foreign matter, and turn the bottle plate and unscrambler to confirm that it can work normally.
3. Turn on the Bottle Unscrambler power switch, check the touch screen and three photoelectric switches. If both are energized, the lack of a bottle alarm will be displayed on the touch screen. When the electric eye is blocked by hand, the screen displays the blocking alarm, and the two photoelectric switches are in a normal state.
4. Turn on the Bottle Unscrambler compressed air, use the bottom of the bottle to shake under the electric eye of the bottle puller, compressed air will be sprayed out, and the equipment can be turned on normally.
To ensure that the various parts of the Bottle Unscrambler can work normally, the formal operation can be divided into five steps: click the host start and lift start on the touch screen respectively, and observe whether the Bottle Unscrambler has abnormal noise when it is running. After powering on the Bottle Unscrambler and confirming that there is no abnormal condition, stop the device, but the qualified infusion bottle upright in the bottle feeding bracket, and start the device again. The bottle will pass through the rotating carousel of the device and enter the conveyor belt to start the bottle unscramble operation. Run at low speed when starting up, and then adjust the lifting speed and unscramble speed according to the actual production, so that the speed of the Bottle Unscrambler equipment can match the actual production speed. To prevent such phenomena from happening. If such a phenomenon occurs, stop the machine immediately to eliminate the fault before it can continue to run. During the operation of the equipment, the bottles should be put in continuously, and observe whether there are phenomena such as pouring, jamming, broken bottles, etc. If any, stop the machine immediately and start the production after troubleshooting. After the production is over, stop the equipment, turn off the power of the Bottle Unscrambler, and clear the remaining materials out of the equipment.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. When the Liquid Filling Machine leaves the factory, it will provide customers with detailed Liquid Filling Machine operation procedures and operating specifications. If you are interested in Liquid Filling Machine, you can contact us, our website is www.cnzpack.com.