











After the Labeling machine sensor sends a signal that the labeling object is ready to be labeled, the drive wheel on the Labeling machine turns up. As the rolled label is in a tight state on the equipment, when the Labeling machine backing paper is tightly attached to the peeling plate and changes direction, the Labeling machine label is forced to disengage due to the rigidity of its material and is ready to be labeled. At this time, the labeling object is located just below the label, under the action of the labeling wheel, to achieve synchronous labeling. After the Labeling machine has finished labeling, the sensor under the roll label sends a stop signal, the drive wheel comes to a standstill, and a labeling cycle end. No matter which type of Labeling machine, the labeling process is roughly the same. The difference is that the installation position of the Labeling machine is different, the labeling object is conveyed differently and positioned differently, and the form of the labeling roller of the Labeling machine is also different. So, what are the Labeling machine's requirements for labels? Let's look at it together next.
This is the content list:
l Surface material
l Release force
l At the end of the paper
l Processing quality
Surface material
Labeling machine label stiffness is the key to labeling, so the Labeling machine surface material is required to have a certain strength and hardness. Labeling machine label stiffness and the thickness of the material and the area of the label, so the Labeling machine in the use of soft film material should be appropriate to increase its thickness, generally controlled at 100μm or more. Labeling machine thin paper materials, such as 60 ~ 70g/m2 labeling paper, are generally not suitable for the production of large labels, but suitable for processing into small labels, such as price tags used on the price tag. Labeling machine label stiffness is not good, it will cause labeling out of the label, or label and backing paper reward so that the automatic labeling failure.
Peel-off force
Labeling machine peel-off force is the force at which the label is separated from the backing paper by the Labeling machine. The Labeling machine release force is related to the type and thickness of the adhesive, the silicone coating on the surface of the backing paper, and the ambient temperature at the time of labeling. If the Labeling machine release force is too small, the label will easily fall off (leave the backing paper) during the conveying process. The Labeling machine's release force is too large, the label will be difficult to detach from the backing paper, and it will not be able to produce labels. The Labeling machine should be integrated control of the technical indicators so that the release force is maintained within a reasonable range.
At the end of the paper
Is also an important indicator to control automatic labeling. The requirements of the Labeling machine base paper surface silicon-coated evenly, the Labeling machine peeling force is consistent. Uniform thickness and good tensile strength ensure that the Labeling machine will not break when labeling. Uniform thickness and good light transmission of the Labeling machine ensure that the sensor can correctly identify the location of the label.
Processing quality
Requires that both sides of the Labeling machine backing paper after slitting should be flat and free of fracture to avoid the backing paper from breaking when the tension changes. Labeling machine die-cutting, to avoid cutting through the backing paper or damage to the silicone layer. If the Labeling machine backing paper and silicone coated layer are destroyed, the Labeling machine backing paper will break easily or the glue in the label will penetrate the backing paper. In addition, the static electricity in the web label must be eliminated before Labeling machine labeling, because static electricity will lead to Labeling machine labeling failure or labeling inaccuracy.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. Before the Labeling machine leaves the factory, it will conduct a large number of tests on the Labeling machine to maintain the healthy development of the Labeling machine market. If you are interested in the Labeling machine, you can contact us, our website is www.cnzpack.com.
The tube Filling machine And the Sealing machine are determined by multiple parameters. It is impossible to describe a Tube Filling machine And Sealing machine with any single parameter. Shaft power, blade displacement, pressure head, blade diameter, and filling speed are the five basic parameters that describe a Tube Filling Machine And Sealing machine. So, let's take a look at the principle of the Tube Filling machine And Sealing machine together. Here are some answers.
Here is the content list:
l Basic parameters.
l The shear rate of the fluid.
l Small slot and big slot.
Basic parameters.
The displacement of the blade is proportional to the flow rate of the blade itself, the first power of the blade speed, and the third power of the blade diameter. The shaft power consumed by the filling is proportional to the specific gravity of the fluid, the power standard of the blade itself, the third power of the speed, and the fifth power of the blade diameter. In the case of a certain power and blade form, the blade displacement and pressure head can be adjusted by changing the diameter of the blade and the matching of the speed. That is, the large diameter blade is equipped with a low-speed Tube Filling machine And a Sealing machine. High flow effect and low-pressure head, while the small diameter blade with high speed produces a higher pressure head and lower flow effect.
The shear rate of the fluid.
In the filling tank, the only way to make the micelles collide with each other is to provide a sufficient shear rate. According to the mechanism of the Tube Filling Machine And Sealing machine, it is because of the existence of fluid velocity difference that the fluid layers are mixed. Therefore, where the filling process always involves the fluid shear rate lhhaha620. Shear stress is a force that is the real cause of bubble dispersion and droplet breaking in filling applications. It must be pointed out that the shear rate at each point of the fluid in the entire stirred tank is not the same.
Small slot and big slot.
Experimental research shows that, as far as the blade area is concerned, no matter what type of blade, when the diameter of the blade is constant, the maximum shear rate and the average shear rate increase with the increase of the speed. However, when the rotation speed is constant, the relationship between the maximum shear rate and the average shear rate, and the diameter of the blade is related to the slurry type. When the rotation speed is constant, the maximum shear rate of the radial blade increases with the increase of the blade diameter, and the average shear rate has nothing to do with the diameter of the blade. These concepts about the shear rate of the blade area require special care in the design of the Tube Filling Machine And Sealing machine to reduce and enlarge. Because the small groove is compared with the large groove, the small groove Tube Filling Machine and Sealing machine often has the characteristics of high speed, small blade diameter, and low tip speed. The large groove Tube Filling Machine And Sealing machine often has the characteristics of low speed, large blade diameter, and high tip speed.
Our official website is https:// www.cnzpack.com/. If you are engaged in work related to the Tube Filling machine And Sealing machine, you can communicate with us on the website.
There is already a lot of knowledge about the Labeling Machine in the market, but the Labeling Machine will appear crooked in the process of using it. How should this be solved? Let's take a look together next.
This is the content list:
Reasons for Labeling Machine crooked during use
Labeling Machine appears to "post crooked" solution
Why does Labeling Machine post crookedly during use? There are two factors: one is running in an environment that is not suitable for Labeling Machine work, and the other is the lack of maintenance of Labeling Machine equipment. The round Labeling Machine adopts self-adhesive roll labeling paper, and the labeling adopts the rolling method to complete the labeling process. The self-adhesive Labeling Machine is clean and hygienic, non-mold, beautiful, and firm after labeling, and will not fall off by itself, and production efficiency Higher merits. If you can do both of these things, you can eliminate the problem of inaccurate labeling.
First, stop the Labeling Machine, and then inspect whether the labeling heads on both sides of the Labeling Machine are loose. Use the tools configured by the manufacturer to stabilize the Labeling Machine. Check whether the Labeling Machine wraps the label's trays for looseness or uneven rotation speed. Add engine oil to lubricate. Round bottle Labeling Machine realizes labeling or filming on the circumferential surface of cylindrical and conical products, such as glass bottles, plastic bottles, etc. It can realize circumferential, semicircular, circumferential double-sided, circumferential positioning labeling and other functions, mainly vertical There are two ways of labeling and horizontal labeling. Then inspect the parameters of the Labeling Machine operating system to avoid labeling different products under the same parameters of the Labeling Machine. Finally, adjust the labeling head and place the labeling product separately. When the conveyor belt is conveyed, whether the Labeling Machine shakes or shakes the first two These steps must be performed after the Labeling Machine stops. If the above two cannot solve the labeling problem of the Labeling Machine, please do not disassemble and replace the internal parts of the device privately. You need to transfer the professional to repair the Labeling Machine.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. So far, we have more than 100 domestic customers and more than 400 foreign customers. The quality of our Labeling Machine and service as well as our integrity are widely praised at home and abroad. We will carry forward the spirit of "comprehensive innovation and perseverance", self-discipline and strive for the first place, and provide new and old customers with better and more complete services with enthusiasm and a new attitude. It can be seen that we have developed well in the quality of Labeling Machine products. Labeling Machine's first-class product quality and efficient and fast after-sales service have created excellent products of "Zhonghuan". If you are interested in Labeling Machine, you can contact us, our website is www.cnzpack.com. I look forward to your coming and hope to cooperate with you.
Capping Machine operation, accuracy error, installation adjustment, equipment cleaning, maintenance, and other aspects are very simple and convenient. Capping Machine has been widely used in various industries such as daily chemical and grease, and can fill different high-viscosity fluids. So what are the working principles and structural characteristics of the Capping Machine? Let's take a look together next.
This is the content list:
l How Capping Machine works
l Structural characteristics of Capping Machine
How Capping Machine works
The Capping Machine adopts a new horizontal design, which is light and convenient and can automatically pump the material. For thicker slurry, a hopper can be added. When the Capping Machine is in the "auto" state, the Capping Machine will automatically perform continuous filling at a set speed. Capping Machines can be divided into three types: atmospheric filling machine, vacuum filling machine, and pressure filling machine.
Under normal pressure, Capping Machine can fill the liquid in a self-flowing manner according to the weight of the liquid itself. The filling method is to fill at a pressure greater than atmospheric pressure. The pressure in the liquid storage tank is greater than the pressure in the bottle, and the liquid that needs to be filled will enter the bottle depending on the pressure difference. The key component of the Capping Machine is the PLC operation control system. Under normal pressure, Capping Machine can fill the liquid in a self-flowing manner according to the weight of the liquid itself. The filling method is to fill at a pressure greater than atmospheric pressure. The pressure in the liquid storage tank is greater than the pressure in the bottle, and the liquid that needs to be filled will enter the bottle depending on the pressure difference. The key component of the Capping Machine is the PLC operation control system.
The principle of the Capping Machine is relatively easy to understand. The improved control system simplifies the structure of the machine. It can be seen from the operating conditions and control efficacy tests of the actual application that the automation level of the system has reached the design requirements. This reduces the labor intensity of the operator and makes the production line that needs filling production about 30% higher than before, so the probability of failure of the Capping Machine is significantly reduced.
Structural characteristics of Capping Machine
The design of the Capping Machine is very reasonable and appropriate, the remainder of the machine is very small, and the operation and use are very simple. The pneumatic parts inside the Capping Machine all use new pneumatic components. The piston and cylinder of the Capping Machine cylinder are made of polytetrafluoroethylene and stainless steel to meet the requirements of GMP testing. The filling quantity and filling speed of the Capping Machine can be adjusted at will, and the degree is relatively high.
The Capping Machine can be modified according to actual production needs. It can be transformed into a multi-head system, explosion-proof system, and overflow system. The Capping Machine is suitable for use in food, daily necessities, pesticides, and other industries, and has a broad application prospect.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. The company strictly controls the quality of the Capping Machine. If you are interested in Capping Machine, you can contact us, our website is www.cnzpack.com. I look forward to your coming and hope to cooperate with you.
Capping Machine is filling equipment specially designed for new oral liquid easy-pull bottles. The design is reasonable, the structure is simple, the operation is convenient, and a mechanical stop filling device is provided for lack of bottles. So what are the adjustment methods of the Capping Machine? Let's take a look together next.
This is the content list:
l Capping Machine feeding half adjustment
l Matters needing attention in discharging
l Adjustment of the locking device
l Vibrator adjustment
Capping Machine feeding half adjustment
Adjust the bottle blocking plate on the feeding half of the Capping Machine upwards to shorten the adaptation to the bottle feeding stroke. Adjust downwards to make the Capping Machine adapt to the extension of the bottle feeding stroke. Adjust the positioning bottle position left and right to align the bottle position when the movable tooth is running, so that the bottle can be fed into the positioning tooth smoothly. Adjust the bottle blocking plate of the Capping Machine so that the width of the bottle inlet is about 22 mm.
Adjust the perfusion Capping Machine component. The role of the perfusion Capping Machine component is to make the liquid medicine be delivered to each easy-pull bottle in time through the dosing device, one-way valve, and needle. Therefore, the needle must enter the bottle mouth properly and the filling time must be appropriate. Adjust the Capping Machine side cam to rotate clockwise or counterclockwise so that the needle is inserted into the bottle mouth just after the empty bottle enters the toothed position. And lift the needle before leaving the toothed position. The filling time of the Capping Machine is adjusted. Turn the cam clockwise or reverse the adjustable needle into the bottle mouth and start filling immediately, and stop filling before the needle leaves the bottle mouth.
Matters needing attention in discharging
Since the Capping Machine is an easy-pull bottle filling and locking device, the discharging has been capped and sealed. To prevent the locked bottle from overturning, it must be placed on the Capping Machine discharge hopper before the first bottle is discharged. Several empty bottles can be transported to the discharge hopper smoothly to keep the locked bottles and sent to the next process with the bottle hopper.
Adjustment of the locking device
Capping Machine capping time adjustment, adjust the cam rotation angle. When the filling liquid bottle enters the locking tooth position, the locking shaft has moved and left the bottle cap before the moving tooth approaches the bottle. The capping pressure is adjusted, and the capping pressure is adjusted. The size of the cap pressure is directly related to the quality of the lock. If the pressure is too high to break the easy-pull bottle, and the pressure is too small, it will affect the sealing performance. Therefore, the nut should be adjusted according to the actual average height of the easy-pull bottle to adjust the pressure to the best.
Capping Machine blade action time adjustment, the blade should be close to the bottleneck before the end of the capping, otherwise, the locking effect of some short bottles cannot be achieved. Loosen the nut during adjustment, and adjust the shaft and up and down to make the blade action time sooner or later. When adjusting the lock of the Capping Machine, pay attention to the locking of the nuts after the adjustment of each department. The easy-pull bottle must be used for the initial valve test. The average height must be taken. Irregular easy-pull bottles cannot enter the lock to avoid damage to the parts.
Vibrator adjustment
The Capping Machine adopts the principle of electromagnetic oscillation to drop the bottle cap to the proper position along the track according to a certain movement trajectory. The vibrator is packaged separately when it leaves the factory, and the lower rail opening must be aligned with the movement rail of the easy-pull bottle when installed. To adjust the gap between the magnets of the Capping Machine, loosen the screw, open the cover, adjust the nut, and make the vibration of the Capping Machine low and fast.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It strictly controls the production of the Capping Machine. A large number of factory tests are carried out before Capping Machine leaves the factory to ensure product quality. If you are interested in Capping Machine, you can Contact Us, our website is www.cnzpack.com.
In our production and life, the Liquid Filling Machine has a significant impact on many industries, so what is the method of using the Liquid Filling Machine? Let's go take a look next.
This is the content list:
l The ground wire must be well-grounded before the Liquid Filling Machine works
l Liquid Filling Machine liquid filling system assembly
The ground wire must be well-grounded before the Liquid Filling Machine works.
The ground wire must be well-grounded before the Liquid Filling Machine works, and then the appropriate standard syringe must be selected according to the different filling volumes. Generally, a 1ml syringe is used when the dispensing range is 0.2-1ml. Use a 5ml syringe for 1-5ml.use a 10ml syringe for 5-10ml. The 20ml model uses a 20ml glass infusion device. The 100ml model uses a 100ml glass infusion device, and the 500ml model uses the stainless steel filling system produced by our factory.
Liquid Filling Machine liquid filling system assembly
Pull out the inner core of the Liquid Filling Machine syringe, put the screw sleeve on the inner core of the syringe, and use the screw sleeve to properly fasten it to the lower base (cleanliness must be paid when disassembling the syringe). Place the upper clamp seat on the outlet end of the Liquid Filling Machine syringe jacket, and properly tighten the nuts on both sides to assemble the inner core and outer jacket of the installed Liquid Filling Machine syringe into one body. At this point, the Liquid Filling Machine injection system is assembled.
Place the Liquid Filling Machine valve with the arrow facing upwards and the arrow mark facing outwards and fix it on the fixing screw with a nut. Assemble the Liquid Filling Machine with a complete liquid filling system, align the upper and lower round holes of the liquid filling system components with the upper and lower fixing rods respectively, and put them on the bearing so that the outer end surface and the bearing surface are levels. When assembling the lower end, do not make the screw sleeve and the crank touch to prevent abnormal noise when the crank on the Liquid Filling Machine rotates (the screw sleeve and the crank are about 1mm apart when installed correctly). After the liquid filling system is installed correctly, tighten it. Tighten the screws up and down. Use a short hose to connect the Liquid Filling Machine syringe to the valve connection nozzle. The liquid inlet pipe is connected to the water inlet, and the liquid outlet pipe is connected to the water outlet. To prevent the liquid inlet and outlet pipes from being entangled, clip the liquid inlet and outlet pipes into the ear openings on the side of the casing.
Turn the crank of the Liquid Filling Machine by hand, it should be able to rotate freely, otherwise, the assembly is wrong, you should check whether the Liquid Filling Machine injection system is fastened to the rotating bearing.
Our company has obtained more than 20 invention patents and utility model patents. The main products are a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and online capping machine, capping machine and labeling machine, bottle unscrambler, tube filling and sealing machine, Cartoning machines, and other packaging equipment. If you are interested in Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.
Liquid Filling Machine is used in the beverage, drinking water, and liquor industries and has become a very important equipment in the liquid food industry. function. So what are the main structural designs of Liquid Filling Machine? Let's take a look at it together.
This is the content list:
l The transmission system of Liquid Filling Machine
l Liquid Filling Machine's actuator
l Liquid Filling Machine's control system
l The body part of the Liquid Filling Machine
The transmission system of Liquid Filling Machine
Liquid Filling Machine's transmission system, this part is to transmit power and motion to various actuators, control elements, and auxiliary mechanisms. Liquid Filling Machine's main transmission components include gears, sprockets, worm gears, screws, and nuts, etc.
Liquid Filling Machine's actuator
Liquid Filling Machine's actuator, this part is mainly to achieve the Liquid Filling Machine packaging process operation and auxiliary operation part, packaging process operation refers to filling, auxiliary operation part refers to packaging materials and products supply and delivery, Liquid Filling Machine packaging material output, etc., the actuator is the core of the machine, its action sequence, and movement law according to the process principle and requirements.
Liquid Filling Machine's control system
The control system of the Liquid Filling Machine is to control the relevant parts of the Liquid Filling Machine, allocate the movements to the actuators, and make them coordinate the movements according to the time and sequence, thus realizing the process functions of the Liquid Filling Machine.
The body part of the Liquid Filling Machine
The body of the Liquid Filling Machine is the skeleton of the Liquid Filling Machine, which mainly plays the role of supporting and positioning the parts. The stability of the body is the first consideration in the design, and the center of gravity of the Liquid Filling Machine should be lowered as much as possible to make the Liquid Filling Machine work smoothly.
The mainframe of Liquid Filling Machine is to fix and support all the working actuators, transmission parts, control systems, to ensure their relative position correctness and stability. The vacuum system of the Liquid Filling Machine sucks the air out of the bottle, thus generating negative pressure inside the bottle, the liquid is filled into the bottle from the liquid tank through the liquid supply system and the filling head, when the liquid reaches the required liquid level, the inlet port is closed and the suction port sucks the excess liquid and foam away.
Liquid Filling Machine of Wenzhou Zungwan Intelligent Machinery Co., Ltd. is first-class product quality and efficient and fast after-sales service, which has created the excellent products of "Zhonghuan". To meet the market demand of Liquid Filling Machine is our eternal topic and sincere commitment to our customers. If you are interested in Liquid Filling Machine, please contact us, our website is www.cnzpack.com. We will carry forward the spirit of "comprehensive innovation, perseverance", self-discipline and strive to be the first, with enthusiasm, new attitude to provide new and old customers with more perfect service. We are looking forward to cooperating with you.
The Tube Filling machine And Sealing machine, as its name implies, is a machine that can be filled and sealed. There are different models for different industries. The more commonly used industries are chemicals, food, etc. Next, let's take a look at the introduction of the Tube Filling machine And Sealing machine. Here are some answers.
Here is the content list:
l Basic information of Tube Filling machine And Sealing machine
l Application performance of Tube Filling machine And Sealing machine.
l The main characteristics of the Tube Filling machine And Sealing machine.
Basic information of Tube Filling machine And Sealing machine
Tube Filling machine And Sealing machine adopts closed and semi-closed filling pastes and liquids. The seal has no leakage. The filling weight and volume are consistent. Filling, sealing, and printing can be completed at one time. It is suitable for medicine, daily chemicals, and food. Chemical and other fields of product packaging. Such as: filling and sealing of materials such as piping, ointment, hair dye, toothpaste, shoe polish, adhesive, AB glue, epoxy glue, neoprene, and other materials. Tube Filling machine And Sealing machine is an ideal, practical, and economical filling equipment for pharmaceutical, daily chemical, fine chemical, and other industries.
Application performance of Tube Filling machine And Sealing machine.
First, the transmission part of the Tube Filling machine And Sealing machine is enclosed under the platform, which is safe, reliable, and pollution-free. Second, the filling and sealing part is installed in a semi-closed non-static outer frame visible cover above the platform, which is easy to observe, operate and maintain. PLC control, man-machine dialogue interface. The rotary table is driven by a cam, with fast speed and high precision. Third, in the inclined-hung tube warehouse, the upper tube mechanism is equipped with a vacuum adsorption device, to ensure that the automatic upper tube accurately enters the tube seat. The photoelectric benchmarking workstation uses high-precision probes, stepping motors, etc. To control the hose pattern in the correct position. Fourth, the filling nozzle of the Tube Filling Machine And Sealing machine is equipped with a material cut-off mechanism to ensure the filling quality. No tube no filling. Fifth, the tail sealing adopts internal heating at the end of the tube, and external cooling and cooling devices; the typing workstation automatically prints the word code on the position required by the process. Sixth, fault protection alarm, no tube alarm, door open shutdown, overload shutdown; counting, and quantitative shutdown.
The main characteristics of the Tube Filling machine And Sealing machine.
First, the Tube Filling machine And Sealing machine has a compact design, easy to operate and adjust. Second, the driving part is fully enclosed. Third. The Tube Filling Machine And Sealing machine is a pneumatic tube washing and feeding machine with an intelligent temperature control cooling system. Fourth, the 316L stainless steel contacts comply with GMP standards. Fifth, the Tube Filling machine And Sealing machine provides overload protection. Sixth, the safety interlock is closed when the door is opened. Seventh, the automated workflow from tube installation to finished product output. Eighth, photoelectric induction automatic orientation.
If you want to buy Tube Filling machine And Sealing machine or want to know more about our company, you can communicate with us on the website. Our official website is http:// www.cnzpack.com/.