











Bottle Unscrambler scientific maintenance and daily management institutionalization are very important. Scientific maintenance and the establishment of a daily management and use system have a very important role and significance for the actual use of mechanical products. It improves the standardization and performance of daily maintenance. It is more convenient for people to choose, especially it can be better suited to play the role of mechanical products in actual production. It is necessary to carry out reasonable maintenance and management of Bottle Unscrambler to improve the performance advantages of the product itself and let Bottle Unscrambler can help production in time during operation. So what are the precautions for Bottle Unscrambler? Let's take a look together next.
This is the content list:
l Things to do when installing Bottle Unscrambler
l Precautions when using Bottle Unscrambler
l Matters needing attention when cleaning the automatic Bottle Unscrambler
Things to do when installing Bottle Unscrambler
1. Before installing the Bottle Unscrambler, we need to check the Bottle Unscrambler thoroughly to see if the materials are complete and whether it is damaged. If you find a problem, please communicate with the manufacturer in time to solve it.
2. After checking the completion of the Bottle Unscrambler, follow the installation instructions to assemble the Bottle Unscrambler and adjust accordingly. Then add lubricating oil to the place that needs lubrication to ensure the flexibility of the Bottle Unscrambler.
3. After the test run Bottle Unscrambler, if it runs normally, it means that the installation of Bottle Unscrambler is completed.
Precautions when using Bottle Unscrambler
1. According to Bottle Unscrambler production conditions, choose to use a power supply that meets Bottle Unscrambler specifications.
2. To prevent electric shock, the Bottle Unscrambler must be well-grounded. Please equip the Bottle Unscrambler with a power socket with a ground wire.
3. After turning off the Bottle Unscrambler power switch, there is still strong voltage in some circuits in the electrical control of the machine. If the control circuit needs to be repaired, the power cord must be unplugged to avoid electric shock.
Matters needing attention when cleaning the automatic Bottle Unscrambler
1. If the company needs to disassemble and wash the Bottle Unscrambler, please do not turn off the air source and power supply.
2. Avoid electric shock to Bottle Unscrambler. When disassembling the Bottle Unscrambler, do not directly rinse the body with water, because the Bottle Unscrambler is equipped with electrical control components. If the components contact the water source, there is a risk of electric shock and may damage the Bottle Unscrambler components.
3. It is strictly forbidden to show the residues of the filled items on the Bottle Unscrambler, such as oil stains, paints, etc. The existence of these things will accelerate the corrosion of the Bottle Unscrambler and affect its service life. If any residual items are found, they should be cleaned up in time.
4. Lubricate the Bottle Unscrambler regularly, clean the Bottle Unscrambler every once in a while, and make a cleaning record for later review.
We have obtained ISO9001 quality management system certification, and some products have passed CE certification. The production of Bottle Unscrambler is strictly controlled. If you are interested in Bottle Unscrambler, you can contact us. Our website is www.cnzpack.com.
Liquid Filling Machine is specially designed for filling easy-to-open bottles. It has a reasonable design, simple structure, easy operation, and a mechanical bottle stop filling device. So what is the working principle of a Liquid Filling Machine? Let's take a look together next.
This is the content list:
l Transmission principle of Liquid Filling Machine
l The principle of the filling part of the Liquid Filling Machine
l Liquid Filling Machine's capping system
l The capping head of the Liquid Filling Machine
l The Liquid Filling Machine's tracking and filling mechanism
The Liquid Filling Machine transmits the power to the worm gear shaft of the reducer through the belt pulley, and then the worm gear shaft transmits the power to the paddlewheel shaft, the filling part, and the capping head through each gear. the filling part, the capping head, and each paddle wheel of the Liquid Filling Machine move synchronously, and the power is transmitted to the bottle feeding paddle wheel device through the bevel gear.
The liquid bottle of the Liquid Filling Machine is sent to the transition pulley by the large bottle inlet paddlewheel and then sent to the synchronous belt by the transition pulley. The bottle is dragged forward at a uniform speed by the inserts on the synchronous belt, and the filling needle of the Liquid Filling Machine is inserted into the bottle mouth under the control of the tracking mechanism and runs forward synchronously with the bottle to achieve tracking and filling. The diving needle rises with the liquid level to play the role of defoaming.
The cap supply system of the Liquid Filling Machine is composed of a cap delivery track, cap handling head, and cap-wearing mechanism. The lid management head adopts the principle of electromagnetic spiral oscillation to line up the messy lids and enter the lid delivery track through the reversing twist channel. When the Liquid Filling Machine passes through the lid-wearing mechanism, the bottle hangs on to the lid and passes through the pressure plate to make the lid wear correctly.
After the liquid bottle of Liquid Filling Machine enters the cap rolling head turntable with the cap on, the three rolling knives which have been opened will turn forward with the Liquid Filling Machine turntable with the bottle as the center and press the cap under the control of the cam, then the three rolling knives will roll towards the cap at the same time under the action of the cone sleeve, and after rolling, they will leave the cap at the same time and return to the original position.
The Liquid Filling Machine drives the gear and rack to move, thus driving the filling needle to do the reciprocating movement. By adjusting the relative position of the Liquid Filling Machine's syringe holder and mounting frame, the filling needle can be accurately inserted into the middle of the bottle opening.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, and so far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and services as well as our integrity are widely praised at home and abroad. We will carry forward the spirit of "comprehensive innovation, perseverance", self-discipline and strive for the first, with enthusiasm and a new attitude to provide more perfect service for new and old customers. If you are interested in Liquid Filling Machine, please contact us, our website is www.cnzpack.com
The Mid-Autumn Festival is the second most important festival for a family reunion in China after the Spring Festival. Besides China, the Mid-Autumn Festival is also celebrated in many other Asian countries like Vietnam, Singapore, and Japan.
The Mid-Autumn Festival is also called the Moon Festival or Mooncake Festival. It would be celebrated on 21 September 2021. Gathering with families, eating moon cakes, and appreciating the fullest moon with lanterns, the Mid-Autumn Festival is a grand time for family reunions.
Besides those traditions in China, other Asian countries have their own unique customs of the Mid-Autumn Festival.
For example, the Mid-Autumn Festival is named Tết Trung Thu in Vietnamese. It is also known as a Children Festival. During the festival, parents will accompany their children and give them gifts like masks or lanterns. Most gifts are made by hand rather than buying at shops. Children would light lanterns and join in lion dance at the Mid-Autumn Festival.
Read Mid-Autumn Festival around the World to find more traditions in other countries.
In our production and life, the Cartoning Machine is of great significance to us, but sometimes, the Cartoning Machine will fail, so what is the reason for the failure of the Cartoning Machine? Next, let us analyze it together.
This is the content list:
Stop or stop between conveyor belts
The carton cannot be sucked down
The carton is not formed or ejected at the mouth of the box feeding template after being sucked
Can't suck the instructions
The paper rebounds during the suction process of the manual
The manual does not fold well
Uneven folding of the manual
There are curls and creases after the manual is folded
Manual stuck in the fence
1. Cartoning Machine shuts down at intervals to check if there is a shortage of materials and automatically starts up when supplemented.
2. Shut down the Cartoning Machine to check whether the power supply including the power supply part, the motor, or the governor is normal.
1. Whether the cartons of Cartons Machine are arranged neatly.
2. Whether the cartons of the Cartoning Machine are pasted together.
3. Whether the air pressure of the Cartoning Machine suction head is normal.
1. Check if the cartons of Cartons Machine are too hard.
2. Check whether the position of the guide rod of the cartons placed by the Cartoning Machine and the box delivery template are not correct.
3. Check whether the small hook spring at the rear of the Cartoning Machine delivery template is deformed.
4. Check if the height of the suction head of the Cartoning Machine and the box delivery track is correct.
1. Whether the Cartoning Machine manual is deformed, causing the suction head to fail to suck.
2. Whether the suction head gas of the Cartoning Machine is parallel to the manual.
3. Whether the paper width of the Cartoning Machine manual is different, the error must be within 1mm. The stacking position of the manual should be adjusted to a difference of 0.5mm from the inner edge when the suction head rises to the high position.
4. The small paper-separating hook above the suction head of the Cartoning Machine origami moves too early. Generally, the small hook should be inserted into the gap between the paper and the paper before the suction head is about to drop. The height of the small hook is adjusted to be 0.5mm away from the suction head when it is in the high position.
1. The foot-lifting action of the Cartoning Machine's manual was too early, and the manual was taken away by the foot support before being pulled down. The position of the feet of the Cartoning Machine is so that it does not touch the sucked manual when it is returned and it returns to the high position when the paper picking notch wheel has not pulled the paper.
2. Whether the matching speed of the Cartoning Machine suction head and paper picking wheel is the same. The suction head of the Cartoning Machine should be lowered first, and then the front part of the paper picking notch wheel should be pressed onto the paper.
1. Check if the Cartoning Machine paper is deformed and bent, and if there are burrs.
2. Is there any foreign matter in the fence of the Cartoning Machine blocking the paper?
3. The gap between the opening of the Cartoning Machine fence and the folding stick is too large, causing the paper to come out.
4. Is the gap between Cartons Machine's folding sticks too large to hold the paper? Adjust the adjusting screws at both ends of the folding stick to reduce the gap. If the Cartoning Machine folding stick has been used for too long and worn out, the folding stick must be replaced.
Check the Cartoning Machine to adjust the front and rear positions of the barriers in the fence to achieve the required folding size.
1. Is the gap between the Cartoning Machine baffle and the folding stick too large? Adjust the middle position of the baffle and folding stick.
2. If the middle position of the Cartoning Machine baffle and the folding stick has been adjusted, and there is still a large gap, remove the positioning pins on the Cartoning Machine baffle and re-adjust until the gap does not feed paper.
1. Whether the paper feeding gap of Cartoning Machine folding stick is too large and paper feeding is weak. The adjustment method is the same as above.
2. The installation position of the lower half of the Cartoning Machine fence is too long than the arc guide plate on it so that the paper cannot enter the folding stick below. Loosen all the fixing screws on the Cartoning Machine fence and adjust the board backward, but it should not be shorter than the upper guide plate and should be 1-3 mm longer than the guide plate. If it is shorter than the guide plate, the Cartoning Machine manual may go directly into the folding stick below without folding.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It will conduct a large number of tests before the Cartoning Machine leaves the factory to reduce the failure of the Cartoning Machine and provide warranty services. If you are interested in the Cartoning Machine, you can contact us Contact, our website is www.cnzpack.com.
Cartoning machine is the description of automatic loading of medicine bottles, trays, ointments, etc. into folded cartons and completing the capping action. Some Cartoning machines with stronger functions also have functions such as sealing labels or heat shrink packaging. So what are the considerations for the daily maintenance of the Cartoning machine? Let's take a look together next.
This is the content list:
l Comply with safe operating procedures
l Refuel or change the oil on time
l Be organized
l Clean inside and outside of equipment
Comply with safe operating procedures
Comply with the Cartoning machine's safety operating procedures and do not overload the equipment. The Cartoning machine's safety protection devices are complete and reliable, and unsafe factors are eliminated in time. For example: Do not touch the inverter within 5 minutes after the power of the Cartoning machine is cut off because it will have a relatively high residual voltage, which will be released after a few minutes. After the Cartoning machine work is finished, you should do a good job of cleaning, use a brush to remove all unclean things, and check whether the power is turned off.
Refuel or change the oil on time
Cartoning machine is well lubricated, add oil or change oil on time, keep oiling, no dry friction. The Cartoning machine should be refueled before starting up. Where there is reciprocating motion, add oil, twice a day, 5-6 drops each time. Add butter once a month to the bearings of the rotating part on both sides of the folding machine. Grease the sliding part of the tongue guide once a week.
Be organized
Cartoning machine tools, accessories, and workpieces (products) should be neatly arranged, Cartoning machine pipes and lines should be organized.
Equipment interior and exterior clean
The interior and exterior of the Cartoning machine equipment should be clean and tidy. All sliding surfaces, lead screws, rack and pinion, gearbox, oil holes, etc. are free of oil and dirt, and all parts of the Cartoning machine do not leak oil or air. The debris, debris, and dirt around the equipment should be cleaned up. For example, there should be no foreign objects in the main motor of the Cartoning machine, the casing should be kept clean, the cooling fan should be good, and it should be maintained regularly. Cartoning machine photoelectric switch and proximity switch detection surface should not have foreign matter and pollution, otherwise, it will cause malfunction. The detection distance should be properly adjusted, and the bracket should be kept tight and not loose to avoid damage when the machine is running. The electrical components inside and outside the electrical cabinet of the Cartoning machine must be kept clean and well dissipated.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It will test the Cartoning machine before leaving the factory and provide warranty service. If you are interested in Cartoning machine, you can contact us. Our website is www.cnzpack.com. I look forward to your coming and hope to cooperate with you.
In our production and life, the Liquid Filling Machine has a significant impact on many industries, so what is the method of using the Liquid Filling Machine? Let's go take a look next.
This is the content list:
l The ground wire must be well-grounded before the Liquid Filling Machine works
l Liquid Filling Machine liquid filling system assembly
The ground wire must be well-grounded before the Liquid Filling Machine works.
The ground wire must be well-grounded before the Liquid Filling Machine works, and then the appropriate standard syringe must be selected according to the different filling volumes. Generally, a 1ml syringe is used when the dispensing range is 0.2-1ml. Use a 5ml syringe for 1-5ml.use a 10ml syringe for 5-10ml. The 20ml model uses a 20ml glass infusion device. The 100ml model uses a 100ml glass infusion device, and the 500ml model uses the stainless steel filling system produced by our factory.
Liquid Filling Machine liquid filling system assembly
Pull out the inner core of the Liquid Filling Machine syringe, put the screw sleeve on the inner core of the syringe, and use the screw sleeve to properly fasten it to the lower base (cleanliness must be paid when disassembling the syringe). Place the upper clamp seat on the outlet end of the Liquid Filling Machine syringe jacket, and properly tighten the nuts on both sides to assemble the inner core and outer jacket of the installed Liquid Filling Machine syringe into one body. At this point, the Liquid Filling Machine injection system is assembled.
Place the Liquid Filling Machine valve with the arrow facing upwards and the arrow mark facing outwards and fix it on the fixing screw with a nut. Assemble the Liquid Filling Machine with a complete liquid filling system, align the upper and lower round holes of the liquid filling system components with the upper and lower fixing rods respectively, and put them on the bearing so that the outer end surface and the bearing surface are levels. When assembling the lower end, do not make the screw sleeve and the crank touch to prevent abnormal noise when the crank on the Liquid Filling Machine rotates (the screw sleeve and the crank are about 1mm apart when installed correctly). After the liquid filling system is installed correctly, tighten it. Tighten the screws up and down. Use a short hose to connect the Liquid Filling Machine syringe to the valve connection nozzle. The liquid inlet pipe is connected to the water inlet, and the liquid outlet pipe is connected to the water outlet. To prevent the liquid inlet and outlet pipes from being entangled, clip the liquid inlet and outlet pipes into the ear openings on the side of the casing.
Turn the crank of the Liquid Filling Machine by hand, it should be able to rotate freely, otherwise, the assembly is wrong, you should check whether the Liquid Filling Machine injection system is fastened to the rotating bearing.
Our company has obtained more than 20 invention patents and utility model patents. The main products are a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and online capping machine, capping machine and labeling machine, bottle unscrambler, tube filling and sealing machine, Cartoning machines, and other packaging equipment. If you are interested in Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.
In our production and life, Capping Machine is also called a Capping Machine, Capping Machine, or Capping Machine, which is used for screwing and unscrewing the caps of plastic bottles and glass bottles (molded bottles or tube bottles). equipment. Capping Machine is highly intelligent capping equipment with advanced technology, unique design, and easy operation. During the entire capping process, workers only need to place the cap on the mouth of the bottle, and then the bottle is automatically sent to the capping wheel and automatically tightened to complete the capping operation. The Capping Machine evacuates the packaging bottle and then tightens it, which prolongs the storage time of the packaging, reduces the failure rate of the Capping Machine, and improves the packaging efficiency of the Capping Machine. So what are the matters needing attention when operating Capping Machine correctly? Let's take a look together next.
This is the content list:
l Capping Machine rolling wheel adjustment
l Capping Machine lock wheel adjustment
l Capping Machine cap lock
l Capping Machine height adjustment
Capping Machine rolling wheel adjustment
Place the Capping Machine bottle on the bracket and raise the bracket to the highest point. First, loosen the lock nut to adjust the rolling wheel so that the (sprung) edge of the two Capping Machine rolling wheels is at the threading of the bottle. Click on it, then loosen the lock nut, and then adjust the adjusting screw so that the edges of the two rolling wheels are in contact with the cover, and a little pressure is appropriate, and then tighten the nut.
Capping Machine lock wheel adjustment
Adjust the two Capping Machine locking wheels, first loosen the locking nuts, adjust the locking wheels so that the edges of the two locking wheels are in contact with the lower edge of the bottle cap, a little pressure is appropriate, and then tighten the nuts (Note: Adjust Capping Machine Should be from loose to tight, adjust while pulling the lock).
Capping Machine cap lock
Loosen the top screw, remove the Capping Machine gland head, and then remove the entire Capping Machine lock head, install the appropriate plastic lock head on the cone sleeve, and then adjust the lifting height of the bracket to meet the working requirements.
Capping Machine height adjustment
Start the Capping Machine to lower the bracket to the lowest point, then place the bottle on the bracket, loosen the brake nut, turn the adjusting screw to raise the bracket, and then adjust the appropriate distance between the cap of the Capping Machine and the capping head (generally All are adjusted in place at the factory).
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. We have obtained ISO9001 quality management system certification, and some products have passed CE certification. Our company has obtained more than 20 invention patents and utility model patents. If you are interested in Capping Machine, you can contact us, our website is www.cnzpack.com.
Korea East Asia Pharmaceutical Company, ordered a syrup filling line from our company, from bottle management - bottle washing - filling - corking - capping - labeling, the whole line in the Korean factory to complete the commissioning task, the whole line production design speed of 120 bottles per minute high-speed filling line.