leidex lipstick filling machine factory- Factory Suppliers Manufacturers From China

After the Labeling machine sensor sends a signal that the labeling object is ready to be labeled, the drive wheel on the Labeling machine turns up. As the rolled label is in a tight state on the equipment, when the Labeling machine backing paper is tightly attached to the peeling plate and changes direction, the Labeling machine label is forced to disengage due to the rigidity of its material and is ready to be labeled. At this time, the labeling object is located just below the label, under the action of the labeling wheel, to achieve synchronous labeling. After the Labeling machine has finished labeling, the sensor under the roll label sends a stop signal, the drive wheel comes to a standstill, and a labeling cycle end. No matter which type of Labeling machine, the labeling process is roughly the same. The difference is that the installation position of the Labeling machine is different, the labeling object is conveyed differently and positioned differently, and the form of the labeling roller of the Labeling machine is also different. So, what are the Labeling machine's requirements for labels? Let's look at it together next.

This is the content list:

l Surface material

l Release force

l At the end of the paper

l Processing quality

Surface material

Labeling machine label stiffness is the key to labeling, so the Labeling machine surface material is required to have a certain strength and hardness. Labeling machine label stiffness and the thickness of the material and the area of the label, so the Labeling machine in the use of soft film material should be appropriate to increase its thickness, generally controlled at 100μm or more. Labeling machine thin paper materials, such as 60 ~ 70g/m2 labeling paper, are generally not suitable for the production of large labels, but suitable for processing into small labels, such as price tags used on the price tag. Labeling machine label stiffness is not good, it will cause labeling out of the label, or label and backing paper reward so that the automatic labeling failure.

Peel-off force

Labeling machine peel-off force is the force at which the label is separated from the backing paper by the Labeling machine. The Labeling machine release force is related to the type and thickness of the adhesive, the silicone coating on the surface of the backing paper, and the ambient temperature at the time of labeling. If the Labeling machine release force is too small, the label will easily fall off (leave the backing paper) during the conveying process. The Labeling machine's release force is too large, the label will be difficult to detach from the backing paper, and it will not be able to produce labels. The Labeling machine should be integrated control of the technical indicators so that the release force is maintained within a reasonable range.

At the end of the paper

Is also an important indicator to control automatic labeling. The requirements of the Labeling machine base paper surface silicon-coated evenly, the Labeling machine peeling force is consistent. Uniform thickness and good tensile strength ensure that the Labeling machine will not break when labeling. Uniform thickness and good light transmission of the Labeling machine ensure that the sensor can correctly identify the location of the label.

Processing quality

Requires that both sides of the Labeling machine backing paper after slitting should be flat and free of fracture to avoid the backing paper from breaking when the tension changes. Labeling machine die-cutting, to avoid cutting through the backing paper or damage to the silicone layer. If the Labeling machine backing paper and silicone coated layer are destroyed, the Labeling machine backing paper will break easily or the glue in the label will penetrate the backing paper. In addition, the static electricity in the web label must be eliminated before Labeling machine labeling, because static electricity will lead to Labeling machine labeling failure or labeling inaccuracy.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. Before the Labeling machine leaves the factory, it will conduct a large number of tests on the Labeling machine to maintain the healthy development of the Labeling machine market. If you are interested in the Labeling machine, you can contact us, our website is www.cnzpack.com.

In our production and life, the Liquid Filling Machine has a significant impact on many industries, so what is the method of using the Liquid Filling Machine? Let's go take a look next.

This is the content list:

l The ground wire must be well-grounded before the Liquid Filling Machine works

l Liquid Filling Machine liquid filling system assembly

The ground wire must be well-grounded before the Liquid Filling Machine works.

The ground wire must be well-grounded before the Liquid Filling Machine works, and then the appropriate standard syringe must be selected according to the different filling volumes. Generally, a 1ml syringe is used when the dispensing range is 0.2-1ml. Use a 5ml syringe for 1-5ml.use a 10ml syringe for 5-10ml. The 20ml model uses a 20ml glass infusion device. The 100ml model uses a 100ml glass infusion device, and the 500ml model uses the stainless steel filling system produced by our factory.

Liquid Filling Machine liquid filling system assembly　　

Pull out the inner core of the Liquid Filling Machine syringe, put the screw sleeve on the inner core of the syringe, and use the screw sleeve to properly fasten it to the lower base (cleanliness must be paid when disassembling the syringe). Place the upper clamp seat on the outlet end of the Liquid Filling Machine syringe jacket, and properly tighten the nuts on both sides to assemble the inner core and outer jacket of the installed Liquid Filling Machine syringe into one body. At this point, the Liquid Filling Machine injection system is assembled.

Place the Liquid Filling Machine valve with the arrow facing upwards and the arrow mark facing outwards and fix it on the fixing screw with a nut. Assemble the Liquid Filling Machine with a complete liquid filling system, align the upper and lower round holes of the liquid filling system components with the upper and lower fixing rods respectively, and put them on the bearing so that the outer end surface and the bearing surface are levels. When assembling the lower end, do not make the screw sleeve and the crank touch to prevent abnormal noise when the crank on the Liquid Filling Machine rotates (the screw sleeve and the crank are about 1mm apart when installed correctly). After the liquid filling system is installed correctly, tighten it. Tighten the screws up and down. Use a short hose to connect the Liquid Filling Machine syringe to the valve connection nozzle. The liquid inlet pipe is connected to the water inlet, and the liquid outlet pipe is connected to the water outlet. To prevent the liquid inlet and outlet pipes from being entangled, clip the liquid inlet and outlet pipes into the ear openings on the side of the casing.

Turn the crank of the Liquid Filling Machine by hand, it should be able to rotate freely, otherwise, the assembly is wrong, you should check whether the Liquid Filling Machine injection system is fastened to the rotating bearing.

Our company has obtained more than 20 invention patents and utility model patents. The main products are a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and online capping machine, capping machine and labeling machine, bottle unscrambler, tube filling and sealing machine, Cartoning machines, and other packaging equipment. If you are interested in Liquid Filling Machine, you can contact us. Our website is www.cnzpack.com.

There is already a lot of knowledge about the Labeling Machine in the market, but the Labeling Machine will appear crooked in the process of using it. How should this be solved? Let's take a look together next.

This is the content list:

Reasons for Labeling Machine crooked during use

Labeling Machine appears to "post crooked" solution

Reasons for Labeling Machine crooked during use

Why does Labeling Machine post crookedly during use? There are two factors: one is running in an environment that is not suitable for Labeling Machine work, and the other is the lack of maintenance of Labeling Machine equipment. The round Labeling Machine adopts self-adhesive roll labeling paper, and the labeling adopts the rolling method to complete the labeling process. The self-adhesive Labeling Machine is clean and hygienic, non-mold, beautiful, and firm after labeling, and will not fall off by itself, and production efficiency Higher merits. If you can do both of these things, you can eliminate the problem of inaccurate labeling.

Labeling Machine appears to "post crooked" solution

First, stop the Labeling Machine, and then inspect whether the labeling heads on both sides of the Labeling Machine are loose. Use the tools configured by the manufacturer to stabilize the Labeling Machine. Check whether the Labeling Machine wraps the label's trays for looseness or uneven rotation speed. Add engine oil to lubricate. Round bottle Labeling Machine realizes labeling or filming on the circumferential surface of cylindrical and conical products, such as glass bottles, plastic bottles, etc. It can realize circumferential, semicircular, circumferential double-sided, circumferential positioning labeling and other functions, mainly vertical There are two ways of labeling and horizontal labeling. Then inspect the parameters of the Labeling Machine operating system to avoid labeling different products under the same parameters of the Labeling Machine. Finally, adjust the labeling head and place the labeling product separately. When the conveyor belt is conveyed, whether the Labeling Machine shakes or shakes the first two These steps must be performed after the Labeling Machine stops. If the above two cannot solve the labeling problem of the Labeling Machine, please do not disassemble and replace the internal parts of the device privately. You need to transfer the professional to repair the Labeling Machine.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. So far, we have more than 100 domestic customers and more than 400 foreign customers. The quality of our Labeling Machine and service as well as our integrity are widely praised at home and abroad. We will carry forward the spirit of "comprehensive innovation and perseverance", self-discipline and strive for the first place, and provide new and old customers with better and more complete services with enthusiasm and a new attitude. It can be seen that we have developed well in the quality of Labeling Machine products. Labeling Machine's first-class product quality and efficient and fast after-sales service have created excellent products of "Zhonghuan". If you are interested in Labeling Machine, you can contact us, our website is www.cnzpack.com. I look forward to your coming and hope to cooperate with you.

In our production and life, the Cartoning Machine is of great significance to us, but sometimes, the Cartoning Machine will fail, so what is the reason for the failure of the Cartoning Machine? Next, let us analyze it together.

This is the content list:

• Stop or stop between conveyor belts

• The carton cannot be sucked down

• The carton is not formed or ejected at the mouth of the box feeding template after being sucked

• Can't suck the instructions

• The paper rebounds during the suction process of the manual

• The manual does not fold well

• Uneven folding of the manual

• There are curls and creases after the manual is folded

• Manual stuck in the fence

Stop or stop between conveyor belts

1. Cartoning Machine shuts down at intervals to check if there is a shortage of materials and automatically starts up when supplemented.

2. Shut down the Cartoning Machine to check whether the power supply including the power supply part, the motor, or the governor is normal.

The carton cannot be sucked down

1. Whether the cartons of Cartons Machine are arranged neatly.

2. Whether the cartons of the Cartoning Machine are pasted together.

3. Whether the air pressure of the Cartoning Machine suction head is normal.

The carton is not formed or ejected at the mouth of the box feeding template after being sucked

1. Check if the cartons of Cartons Machine are too hard.

2. Check whether the position of the guide rod of the cartons placed by the Cartoning Machine and the box delivery template are not correct.

3. Check whether the small hook spring at the rear of the Cartoning Machine delivery template is deformed.

4. Check if the height of the suction head of the Cartoning Machine and the box delivery track is correct.

Can't suck the instructions

1. Whether the Cartoning Machine manual is deformed, causing the suction head to fail to suck.

2. Whether the suction head gas of the Cartoning Machine is parallel to the manual.

3. Whether the paper width of the Cartoning Machine manual is different, the error must be within 1mm. The stacking position of the manual should be adjusted to a difference of 0.5mm from the inner edge when the suction head rises to the high position.

4. The small paper-separating hook above the suction head of the Cartoning Machine origami moves too early. Generally, the small hook should be inserted into the gap between the paper and the paper before the suction head is about to drop. The height of the small hook is adjusted to be 0.5mm away from the suction head when it is in the high position.

The paper rebounds during the suction process of the manual

1. The foot-lifting action of the Cartoning Machine's manual was too early, and the manual was taken away by the foot support before being pulled down. The position of the feet of the Cartoning Machine is so that it does not touch the sucked manual when it is returned and it returns to the high position when the paper picking notch wheel has not pulled the paper.

2. Whether the matching speed of the Cartoning Machine suction head and paper picking wheel is the same. The suction head of the Cartoning Machine should be lowered first, and then the front part of the paper picking notch wheel should be pressed onto the paper.

The manual does not fold well

1. Check if the Cartoning Machine paper is deformed and bent, and if there are burrs.

2. Is there any foreign matter in the fence of the Cartoning Machine blocking the paper?

3. The gap between the opening of the Cartoning Machine fence and the folding stick is too large, causing the paper to come out.

4. Is the gap between Cartons Machine's folding sticks too large to hold the paper? Adjust the adjusting screws at both ends of the folding stick to reduce the gap. If the Cartoning Machine folding stick has been used for too long and worn out, the folding stick must be replaced.

Uneven folding of the manual

Check the Cartoning Machine to adjust the front and rear positions of the barriers in the fence to achieve the required folding size.

There are curls and creases after the manual is folded

1. Is the gap between the Cartoning Machine baffle and the folding stick too large? Adjust the middle position of the baffle and folding stick.

2. If the middle position of the Cartoning Machine baffle and the folding stick has been adjusted, and there is still a large gap, remove the positioning pins on the Cartoning Machine baffle and re-adjust until the gap does not feed paper.

Manual stuck in the fence

1. Whether the paper feeding gap of Cartoning Machine folding stick is too large and paper feeding is weak. The adjustment method is the same as above.

2. The installation position of the lower half of the Cartoning Machine fence is too long than the arc guide plate on it so that the paper cannot enter the folding stick below. Loosen all the fixing screws on the Cartoning Machine fence and adjust the board backward, but it should not be shorter than the upper guide plate and should be 1-3 mm longer than the guide plate. If it is shorter than the guide plate, the Cartoning Machine manual may go directly into the folding stick below without folding.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It will conduct a large number of tests before the Cartoning Machine leaves the factory to reduce the failure of the Cartoning Machine and provide warranty services. If you are interested in the Cartoning Machine, you can contact us Contact, our website is www.cnzpack.com.

Bottle Unscrambler is suitable for automatic unscramble of plastic round bottles, flat bottles, and tube-top bottles. Disordered bottles are poured into the bottle storage box. The bottles enter the filling machine conveyor line in an upright and orderly manner. The use of the Bottle Unscrambler equipment greatly reduces the labor intensity of the operators, and the equipment is stable and reliable with a high degree of automation. So, what is the structure of Bottle Unscrambler? Let's take a look together next.

This is the content list:

l The lifting mechanism of Bottle Unscrambler

l Bottle Unscrambler's unscrambler mechanism

l Bottle delivery mechanism of Bottle Unscrambler

l Bottle Unscrambler's bottle-out mechanism

The lifting mechanism of Bottle Unscrambler

Bottle Unscrambler has a stainless steel shell, stainless steel support feet, stainless steel large-capacity hopper, no bottle alarm and cap opening function, engineering plastic conveyor belt, which meets GMP requirements.

Bottle Unscrambler Bottle Unscrambler

Bottle Unscrambler adopts automatic quantitative feeding and turntable technology to maintain the dynamic balance of the number of bottles in the unscrambler tray to ensure stable and continuous bottle output. The Bottle Unscrambler enters the Bottle Unscrambler turntable by the lifting mechanism, and the turntable rotates at a high speed to sort out the bottles as required. Bottle Unscrambler web wheel removes irregular bottles.

Bottle delivery mechanism of Bottle Unscrambler

The bottle delivery mechanism of Bottle Unscrambler is a conveyor belt that meets GMP and FDA standards and requirements and uses flexible cushioning to facilitate bottle turnover. The structure of single-motor-driven double-belt pulleys ensures the same speed as the two clamping belts. The bottle-feeding mechanism of the Bottle Unscrambler clamps the bottles to the working surface of the conveyor through the conveyor belts on both sides. The bottle delivery mechanism of Bottle Unscrambler sorts out the bottles through different bottle flippers.

Bottle Unscrambler's bottle-out mechanism

The Bottle Unscrambler's single-motor drive double-pulley structure ensures that the two clamping belts have the same speed. Adjustable clamping belt speed. When the clamping belt sends out the bottle, the speed of the Bottle Unscrambler is the same as that of the main conveyor belt. The Bottle Unscrambler does not invert the bottle. The conveyor belt conforms to GMP and FDA standards and requirements. It adopts flexible buffering and is convenient. The bottle is turned over.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. So far, we have more than 100 domestic customers and more than 400 foreign customers. The quality of our Bottle Unscrambler and service as well as our integrity are widely praised at home and abroad. We will carry forward the spirit of "comprehensive innovation and perseverance", self-discipline and strive for the first place, and provide new and old customers with better and more complete services with enthusiasm and a new attitude. Bottle Unscrambler is in great demand in the domestic and foreign markets. Keep improving, develop to satisfy customers, and meet market needs are our eternal topic and our sincere commitment to customers. If you are interested in Bottle Unscrambler, you can contact us, our website is www.cnzpack.com. We look forward to your coming and hope to cooperate with you.

Liquid Filling Machine is a kind of process machinery, its process characteristics are more obvious, for the design requirements provided by the customer as well as the functions, work efficiency and other aspects of good, then Liquid Filling Machine what are the design principles and considerations? Let's learn about it together.

This is the content list:

l The design principle of Liquid Filling Machine

l Precautions for Liquid Filling Machine

The design principle of Liquid Filling Machine

First, design the parameters of the Liquid Filling Machine and the material to be filled, and then also to understand the container to be filled, to understand the shape of the container and the characteristics of the container cap, according to these characteristics design the corresponding bottle Liquid Filling Machine.

Secondly, we should also know the functions to be achieved by the Liquid Filling Machine, the principle and method of Liquid Filling Machine filling, the whole process of Liquid Filling Machine filling should be carefully understood, and each link should be designed reasonably and appropriately to avoid affecting the effect of filling.

Liquid Filling Machine should also be based on the specific needs of enterprises, the use of functional principles of innovative design methods to design filling equipment to meet the production needs of enterprises, which will not only improve efficiency but also reduce the rate of damage and reduce the production costs of enterprises.

Precautions for Liquid Filling Machine

First, check the Liquid Filling Machine itself to determine if the ball valve in the filling machine is damaged or loose. If the internal ball valve of the Liquid Filling Machine is the cause, the solution is to replace the internal ball valve. If the internal ball valve of the Liquid Filling Machine is damaged, there is no way to repair it, only to replace it with a new one.

Check that the Liquid Filling Machine syringe assembly is clean. If it is not clean, it will cause an unclean blockage between the inner and outer tubes, so remove the Liquid Filling Machine syringe, clean it and disinfect and maintain it.

Check that the Liquid Filling Machine filler nozzle is complete. If the Liquid Filling Machine filling nozzle is damaged, the equipment will leak during operation. Replace broken filling nozzles and inspect other filling nozzles for use, deterioration, or corrosion, and replace them as soon as possible.

Check whether the O-ring is corroded or worn. If the O-ring is corroded or worn, it will also cause the Liquid Filling Machine to drip. Therefore, in this case, it is recommended to replace the O-ring.

Check the Liquid Filling Machine barrel position. Determine if the cylinder is in the cylinder center support position, and also check if the Liquid Filling Machine cylinder piston and piston rod are secure, and if they are loose, please lock them. If the cylinder failure position is changed, you need to reinstall the cylinder and confirm the correct position.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer, which has made great achievements in Liquid Filling Machine and is loved by the consumers. If you are interested in Liquid Filling Machine, you can contact us, our website is www.cnzpack.com.

Wenzhou Zungwan Intelligent Machine Co.,Ltd. is the professional equipment manufacturer to keep researching and developing the packing machinery for every type of liquid, powder, cream/ointment, fluid and half-fluid etc. materials. We have Obtained ISO9001 quality management system authentication and parts of our products have passed CE authentication. Our company has obtained more than 20 invention patents and utility model patents. The main products range from nail polish filling machine, perfume machine,perfume filling machine, powder serial automatically volume-measuring packing machine and inline capping machine, rotary capping machine and labeling machine, bottle unscrambler , screw capping machine ,tube filling and sealing machine, cartoning machine and other Packaging equipments.

So far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and our service as well as our integrity is acclaimed both in China and abroad. we will carry forward the spirit of "integrated innovation, and perseverance," discipline ourselves to be the first, and provide better and more perfect service for our new and old customers with enthusiasm and a new attitude.

In our daily life, Capping Machine plays a vital role for us, so what are the main work processes and precautions of the Capping Machine? Let's take a look together next.

This is the content list:

• The main workflow of Capping Machine

• How to carry out daily maintenance and maintenance of Capping Machine

• How to deal with common problems of Capping Machine　

The main workflow of Capping Machine

We know that after the plastic bottles are sorted by the Capping Machine, they enter the conveyor chain in a single row. In the filling station, the plunger pump injects the liquid in the container into the plastic bottle. After filling, the plastic bottle enters the index plate and stops accurately at the capping station. Manually place the cap of the Capping Machine at the entrance of the friction beltline, take out the capping claw, screw the cap claw, and squeeze the tube claw to complete the capping action. Then the plastic bottle exits the index plate and enters the conveyor chain, and enters the labeling station to complete the round bottle labeling.

How to carry out daily maintenance and maintenance of Capping Machine

1. Always keep the Capping Machine clean, especially for the electrical appliances on the switchboard, to prevent moisture and dust, and it is forbidden to change the program of the inverter and the program controller at will.　

2. The power supply voltage of the Capping Machine should be stable, not exceeding ±15%, the material temperature should be kept at 10℃-40℃, the ambient temperature should be kept at 5℃～40℃, and the temperature should be kept at 5～95%PH.　

3. The flowmeter used by the Capping Machine for spray filling is a precision instrument. Therefore, the oil must be precision filtered before it can be filled.　　

4. Turn off the power supply and oil inlet valve of the Capping Machine after finishing the work.　　

5. Pay attention to the cleanliness of the infrared sensor from the Capping Machine. Frequently wipe it clean with clean cotton. It is strictly forbidden for any object to approach the sensor during the working process, and strong light should not be directly or reflected on the sensor, otherwise, it will prosper and malfunction.

6. Add cylinder lubricating oil to the pneumatic triplet regularly.　　

7. When the machine is not used for a long time, all parts should be wiped clean and covered with plastic or tarpaulin to prevent dust.

How to deal with common problems of Capping Machine

First, what should I do if the cylinder piston of the Capping Machine does not work? Confirm whether the safety emergency stop switch is safe. Confirm that the air supply switch of the Capping Machine is turned on. Check if the Capping Machine one-way signal valve is damaged.

Second, what should I do if the Capping Machine cylinder piston does not return after being pushed to the top? Confirm whether the moving target is in contact with the one-way valve.

Third, how to adjust the filling volume of the Capping Machine is inaccurate or not discharged?

Check whether the upper and lower throttle valves of the Capping Machine are closed, and increase the pumping speed of the throttle valve of the cylinder. Make sure that the Capping Machine quick-install tee is locked with a clamp. Confirm whether there are enough materials in the Capping Machine storage box. Make sure that the joints of the pipes of the Capping Machine are sealed.

Fourth, what should I do if the material of the Capping Machine flows out from the rear end of the cylinder? Check whether the sealing ring on the Capping Machine piston is worn. If it is worn, replace it and make sure that the piston and the piston rod are tight.

In addition to timely handling of problems, it is also necessary to do a good job of preventive work in advance. Doing a good job in daily maintenance can also reduce the failure rate of the Capping Machine. The daily maintenance and maintenance of the Capping Machine cannot be underestimated. This is a very important step. Daily maintenance on time can effectively extend the service life of the Capping Machine, improve the production efficiency of the enterprise, and keep Capping Machine in normal operation throughout the day, reducing manpower. The loss of material resources.

Wenzhou Zungwan Intelligent Machinery Co., Ltd.'s first-class product quality and efficient and quick after-sales service have created excellent products of "Zhonghuan". Products are in great demand in the domestic and foreign markets. Keep improving, develop to satisfy customers, and meet market demands are our eternal topic and our sincere commitment to customers. Therefore, Capping Machine is very popular among consumers. If you are interested in Capping Machine, you can contact us. Our website is www.cnzpack.com.

Mesin Industri Mesin Pengemas Mesin Pengisi Wholesale kosmetik lotion cair mengisi mesin Kosmetik Lotion Cair Mengisi Mesin (532713 products available) 1/6 Mesin Pengisi Sabun Cair, Mesin Pengisi Sabun Cair, Kosmetik Cair, Lini ProduksiCair ...

best-selling cream / oil filling machine/manual liquid filling machine Liquid Filling Oil Filling Machine Filling Machine

High quality Aluminum Toothpaste Automatic Tube Filling And Sealing Machine from China, China's leading Toothpaste tube filling and sealing machine product, with strict quality control Toothpaste tube filling sealing machine factories, producing high quality

Granule Packing Machine. For 0.1-500g; For 0.5-15kg; Multi-Head Scale Packing Machine; Powder Packing Machine. For 0.1-500g; For 0.5-15kg; Milk Powder Packing Machine; Liquid/Paste Packing Machine. For 1-500mL; For 0.5-10L; Tea Bag Packing Machine; Coffee Bag Packing Machine. For Drip Coffee; For Instant Coffee; For Coffee Bean; Cling Film ...

ZHGX-60EM Continuous Suppository Filling And Capping Machine Introduction ZHGX-60EM Type machine is designed for suppository tube filing and capping.The machine can finish the …

Form fill and seal machine FUJI FW3710 B. USED. Manufacturer: Fuji. Model: FW3710. This machine with a capacity of max. 100 bag s/min. is designed for forming, filling and sealing of tubular bag s. Technical data Max. product sizes. Kreuzau, Germany. Click to …

Our special filling machine FA25 for mascara filling works with a highly accurate volumetric piston dosing technology. The product is sucked from the heated hopper with speed-controlled agitator. It is then carefully filled into the mascara sticks via rotary slide valve and filling needle.

Details and Price about Fully Automatic Tube Filling and Sealing Machine Auto Plastic …