With the continuous development of our production life, the emergence of Pharmaceutical Filler and Capper has brought great convenience to the industry. So what are the procedures and precautions for Pharmaceutical Filler and Capper? Let's take a look at it.
This is the content list:
l The operation method of Pharmaceutical Filler and Capper
l Safety rules for the use of Pharmaceutical Filler and Capper
l Precautions for Pharmaceutical Filler and Capper
The operation method of Pharmaceutical Filler and Capper
Pharmaceutical Filler and Capper installation precautions before use check, after the machine is installed, turn on the power, test runs the three-phase motor to ensure that the correct direction of operation, ensure that the pressure and flow of compressed air, check whether the motor, bearings, etc. need to be lubricated, no oil-free operation is strictly prohibited, normal before starting Pharmaceutical Filler and Capper. Filler And Capper at the same time, observe whether the fasteners of each part are loose, and only after the operation of each part is stable, can it be used normally. Check whether the function of the safety facilities of Pharmaceutical Filler and Capper is normal, check carefully whether there is water in all water tanks, whether the chainplate is stuck, whether there is debris on the conveyor belt, whether there are caps in the storage box, whether the water, power, and gas sources are connected before starting the machine. After all, conditions are ready, then close the main power QF, power indicator light, fault indicator, emergency stop indicator light is not on, then the start conditions are available, press the start button on the control box and the start switch at the filling, after the buzzer three warning, the whole machine starts running, take external washing, rinsing, filling fully automatic work mode, stop can be at the filling and control box press the stop button after the stop should turn off the main power.
Pharmaceutical Filler and Capper safety rules of use
1. No foreign objects (such as tools, rags, etc.) in Pharmaceutical Filler and Capper equipment.
2. Pharmaceutical Filler and Capper should not be allowed to have abnormal noise, if there is, it should be stopped immediately to check the reason.
3. All protective materials should be safe and reliable, it is strictly prohibited to wear clothing that may be hung by moving parts (such as scarves, bracelets, watches, etc.).
4. Long hair, should wear a hair cover.
5. Do not use water and other liquids to clean the electrical unit.
6. Cleaning should wear work clothes, gloves, glasses, etc., to prevent strong acid, strong alkali corrosion.
7. When Pharmaceutical Filler and Capper is running, someone must monitor it and do not approach the machine with tools or other objects.
8. Don't let the staff who are not related to the operation approach the installation of Pharmaceutical Filler and Capper.
Precautions for Pharmaceutical Filler and Capper
1、After unpacking Pharmaceutical Filler and Capper, first check whether the random technical information is complete and whether the machine is damaged in transportation, to solve the problem in time.
2、Install and adjust the feeding and discharging components according to the shape illustration in this manual.
3、Lubricate each lubrication point with new lubricant.
4、Turn the Pharmaceutical Filler and Capper by shaking the handle, check whether the Pharmaceutical Filler and Capper are running in the correct direction (facing the motor spindle in the counterclockwise direction), and the installation precautions of the Pharmaceutical Filler and Capper must be protected from grounding.
If you are interested in Pharmaceutical Filler and Capper, please contact us, our website is www.cnzpack.com.
After the Labeling machine sensor sends a signal that the labeling object is ready to be labeled, the drive wheel on the Labeling machine turns up. As the rolled label is in a tight state on the equipment, when the Labeling machine backing paper is tightly attached to the peeling plate and changes direction, the Labeling machine label is forced to disengage due to the rigidity of its material and is ready to be labeled. At this time, the labeling object is located just below the label, under the action of the labeling wheel, to achieve synchronous labeling. After the Labeling machine has finished labeling, the sensor under the roll label sends a stop signal, the drive wheel comes to a standstill, and a labeling cycle end. No matter which type of Labeling machine, the labeling process is roughly the same. The difference is that the installation position of the Labeling machine is different, the labeling object is conveyed differently and positioned differently, and the form of the labeling roller of the Labeling machine is also different. So, what are the Labeling machine's requirements for labels? Let's look at it together next.
This is the content list:
l Surface material
l Release force
l At the end of the paper
l Processing quality
Labeling machine label stiffness is the key to labeling, so the Labeling machine surface material is required to have a certain strength and hardness. Labeling machine label stiffness and the thickness of the material and the area of the label, so the Labeling machine in the use of soft film material should be appropriate to increase its thickness, generally controlled at 100μm or more. Labeling machine thin paper materials, such as 60 ~ 70g/m2 labeling paper, are generally not suitable for the production of large labels, but suitable for processing into small labels, such as price tags used on the price tag. Labeling machine label stiffness is not good, it will cause labeling out of the label, or label and backing paper reward so that the automatic labeling failure.
Labeling machine peel-off force is the force at which the label is separated from the backing paper by the Labeling machine. The Labeling machine release force is related to the type and thickness of the adhesive, the silicone coating on the surface of the backing paper, and the ambient temperature at the time of labeling. If the Labeling machine release force is too small, the label will easily fall off (leave the backing paper) during the conveying process. The Labeling machine's release force is too large, the label will be difficult to detach from the backing paper, and it will not be able to produce labels. The Labeling machine should be integrated control of the technical indicators so that the release force is maintained within a reasonable range.
At the end of the paper
Is also an important indicator to control automatic labeling. The requirements of the Labeling machine base paper surface silicon-coated evenly, the Labeling machine peeling force is consistent. Uniform thickness and good tensile strength ensure that the Labeling machine will not break when labeling. Uniform thickness and good light transmission of the Labeling machine ensure that the sensor can correctly identify the location of the label.
Requires that both sides of the Labeling machine backing paper after slitting should be flat and free of fracture to avoid the backing paper from breaking when the tension changes. Labeling machine die-cutting, to avoid cutting through the backing paper or damage to the silicone layer. If the Labeling machine backing paper and silicone coated layer are destroyed, the Labeling machine backing paper will break easily or the glue in the label will penetrate the backing paper. In addition, the static electricity in the web label must be eliminated before Labeling machine labeling, because static electricity will lead to Labeling machine labeling failure or labeling inaccuracy.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. Before the Labeling machine leaves the factory, it will conduct a large number of tests on the Labeling machine to maintain the healthy development of the Labeling machine market. If you are interested in the Labeling machine, you can contact us, our website is www.cnzpack.com.
The Cosmetic Filling machine And Capping machine integrates the functions of air purification, filling, inserting, capping, and venting. It is suitable for filling water injection, lotion, and cream products. The Cosmetic Filling machine And Capping machine has the advantages of reasonable design, stable performance, accurate quantity, glass tabletop, automatic bottle feeding, smooth operation and no noise, electric speed regulation of filling speed and filling volume, and convenient maintenance and cleaning. Next, let's take a look at the description and structural characteristics of the Cosmetic Filling machine And capping Machine. Here are some answers.
Here is the content list:
Description of Cosmetic Filling machine And Capping machine.
Structural characteristics of Cosmetic Filling machine And Capping machine.
The Cosmetic Filling machine And Capping machine adopts automatic low-vacuum filling, automatic bottle detection (no bottle no filling), three fillings, automatic lowering of the nozzle cap, circulation of the perfume bottle die, and wide adaptability. It can meet the volume of containers of different sizes and filling requirements. Cosmetic Filling Machine And Capping machine is equipped with air bottle cleaning, quantitative filling, negative pressure filling, pumping, roll cap, jacket, screw cap, rejection, labeling, and finished product collection. The mold moves in a circular motion, which makes it easy to change the bottle. The stepper motor is used for quantitative filling, and the filling volume can be adjusted quickly. The negative pressure device is used to fill the same liquid level and the manipulator releases the pump to increase the pump roll rate; the elastic rolling head is to avoid damage to the bottle body.
The design of the Cosmetic Filling machine And Capping machine is very reasonable. The Cosmetic Filling machine And Capping machine has a reasonable and compact structure, stable operation, flexible operation, and convenient specification conversion and adjustment. The speed of the aluminum cover is adjustable. Using the principle of seven-station three-knife cap rolling, the aluminum cap is rolled without damage, and the rolling mouth is firm, smooth and flat. The operation of the machine is very simple. The internal pneumatic part adopts new pneumatic components. The piston and cylinder of cylinder are made of PTFE and stainless steel, which meets the requirements of GMP testing. The filling speed can be adjusted at will with high precision. The Cosmetic Filling machine And Capping machine can be modified according to actual production needs and can be transformed into a multi-head type, explosion-proof type, and overflow type system.
Wenzhou Zungwan Intelligent Machine Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream, ointment, fluid, and semi-fluid materials. Our official website is https:// www. cnzpack.com/. If you are engaged in work related to Cosmetic Filling machines And Capping machines or want to learn more about our company, you can communicate with us on the website. Our company adheres to the service tenet of "customer first", and implements the service of honesty and customer first.
Most Bag Packing Machines track and adjust various mechanical parameters through intelligent control instruments and menu-type software on the touch screen. The electronic display shows the length of the cut bag, the packaging speed, the net content of the filling, and the packaging output, etc., which can be understood at a glance. The standard color code tracking photoelectric system of the Bag Packing Machine can ensure the correct printing patterns of the packaged products. In addition, Bag Packing Machine can perform online status monitoring and fault diagnosis analysis of the working process. Once a problem occurs, Bag Packing Machine will automatically stop and display the cause and solution of the fault. So how do we maintain the Bag Packing Machine equipment in actual production? Let's take a look together next.
This is the content list:
l Maintenance after production
l Machine parts lubrication
l Care instructions
Maintenance after production
Every day after production, employees must clean the Bag Packing Machine before leaving get off work. First, the material barrels are cleaned in the warehouse, and the remaining materials on the tray are cleaned and kept clean. The remaining materials in other parts are cleaned up to prepare for the next use of the Bag Packing Machine.
Machine parts lubrication
The box part of the Bag Packing Machine is equipped with an oil gauge. The oil should be filled once before the Bag Packing Machine is turned on. It can be added in the middle according to the temperature rise and operating conditions of each bearing. The Bag Packing Machine worm gearbox must store oil for a long time. The oil level is high enough that the worm gear invades the oil. If it is used frequently, the oil must be replaced every three months. There is an oil plug at the bottom for draining oil. When refueling the Bag Packing Machine, do not let the oil spill out of the cup, let alone flow around the Bag Packing Machine and on the ground. Because oil is easy to pollute materials and affect product quality.
Check the parts of the Bag Packing Machine regularly, once a month, check whether the movable parts of the Bag Packing Machine worm gear, worm, lubricating block, bearings, and other moving parts are flexible and worn. If any defects are found, they should be repaired in time and should not be used reluctantly. The Bag Packing Machine should be used in a dry and clean room, and should not be used in places where the atmosphere contains acids and other gases that are corrosive to the body. When the Bag Packing Machine roller moves back and forth during work, please adjust the screws on the front bearing to the proper position. If the gear shaft of the Bag Packing Machine moves, please adjust the screws behind the bearing frame to the proper position, adjust the gap so that the bearing does not make a noise, turn the belt pulley by hand, and tighten properly. Too tight or too loose can make the Bag Packing Machine happen. The possibility of damage. If it is out of service for a long time, the Bag Packing Machine must be wiped and cleaned, and the smooth surface of the machine must be coated with anti-rust oil and covered with a cloth canopy.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that produces first-class Bag Packing Machine product quality and efficient and fast after-sales service, which has created excellent products of "Zhonghuan". Products are in great demand in the domestic and foreign markets. Keep improving, develop to satisfy customers, and meet market demands are our eternal topic and our sincere commitment to customers. If you are interested in Bag Packing Machine, you can contact us, our website is www.cnzpack.com.
The Cosmetic Filling Machine and Capping machine is a professional cosmetic filling and capping equipment, which can make the cap tighter without damaging the mouth of the bottle and effectively protect the cosmetics from contact with the outside world. Next, let's take a look at the use and maintenance of the Cosmetic Filling machine and the capping machine. Here are some answers.
Here is the content list:
l Instructions for use of Cosmetic Filling machine And Capping machine.
l How is the daily maintenance of the Cosmetic Filling machine And Capping machine?
Instructions for use of Cosmetic Filling machine And Capping machine.
First, because the Cosmetic Filling Machine and Capping machine is an automated machine, the dimensions of the pop-up bottle, bottle liner, and bottle cap are required to be uniform. Second, before driving, you must first use the crank handle to turn the machine to see if there is any abnormality in the rotation, and then you can drive after it is confirmed that it is normal. Third, when adjusting the machine, the tools should be used appropriately. It is strictly forbidden to use excessive tools or excessive force to dismantle the parts to avoid damage to the machine parts or affect the performance of the machine. Fourth, the Cosmetic Filling machine and the Capping machine must be kept clean. Before the shift, all parts of the machine surface should be cleaned once, and clean lubricating oil should be added to each activity department. It should be scrubbed once a week, especially the areas that are not easily cleaned in normal use or blown with compressed air.
How is the daily maintenance of the Cosmetic Filling machine And Capping machine?
First, the Cosmetic Filling Machine and the Capping machine has strict requirements for the placement environment and must ensure the indoor humidity is moderate, ventilated, and hygienic. Because the Cosmetic Filling Machine and Capping machine is a mechanical device, after all, the raw materials are some steel electromechanical, etc. It is easy to rust when placed in a humid environment, and a closed environment is not conducive to the heat dissipation of the equipment during operation. Second, you must ensure that the power supply is normal and the grounding wire is safe before use. Voltage instability can cause considerable damage to the machine. Third, the non-woven soft cloth and cleaning agent must be added to wipe off the oil or dirt and wipe dry before the Cosmetic Filling machine and capping machine are operated. After use, take out all the remaining materials to prevent the materials from corroding the equipment and scrub them clean. Periodically clean the invisible dust and garbage in the chassis. And adhere to the tightness of the mechanical parts. Fourth, clean up the machine regularly. Many companies conduct major maintenance on machinery and equipment once a year in autumn. Fifth, add lubricating oil to the mechanical components of the Cosmetic Filling machine and Capping machine regularly to reduce frictional resistance and make the machine run faster.
Our official website is https:// www.cnzpack.com/. If you are engaged in work related to Cosmetic Filling machines and Capping machines or want to learn more about our company, you can communicate with us on the website.
Cartoning machine is the description of automatic loading of medicine bottles, trays, ointments, etc. into folded cartons and completing the capping action. Some Cartoning machines with stronger functions also have functions such as sealing labels or heat shrink packaging. So what are the considerations for the daily maintenance of the Cartoning machine? Let's take a look together next.
This is the content list:
l Comply with safe operating procedures
l Refuel or change the oil on time
l Be organized
l Clean inside and outside of equipment
Comply with safe operating procedures
Comply with the Cartoning machine's safety operating procedures and do not overload the equipment. The Cartoning machine's safety protection devices are complete and reliable, and unsafe factors are eliminated in time. For example: Do not touch the inverter within 5 minutes after the power of the Cartoning machine is cut off because it will have a relatively high residual voltage, which will be released after a few minutes. After the Cartoning machine work is finished, you should do a good job of cleaning, use a brush to remove all unclean things, and check whether the power is turned off.
Refuel or change the oil on time
Cartoning machine is well lubricated, add oil or change oil on time, keep oiling, no dry friction. The Cartoning machine should be refueled before starting up. Where there is reciprocating motion, add oil, twice a day, 5-6 drops each time. Add butter once a month to the bearings of the rotating part on both sides of the folding machine. Grease the sliding part of the tongue guide once a week.
Cartoning machine tools, accessories, and workpieces (products) should be neatly arranged, Cartoning machine pipes and lines should be organized.
Equipment interior and exterior clean
The interior and exterior of the Cartoning machine equipment should be clean and tidy. All sliding surfaces, lead screws, rack and pinion, gearbox, oil holes, etc. are free of oil and dirt, and all parts of the Cartoning machine do not leak oil or air. The debris, debris, and dirt around the equipment should be cleaned up. For example, there should be no foreign objects in the main motor of the Cartoning machine, the casing should be kept clean, the cooling fan should be good, and it should be maintained regularly. Cartoning machine photoelectric switch and proximity switch detection surface should not have foreign matter and pollution, otherwise, it will cause malfunction. The detection distance should be properly adjusted, and the bracket should be kept tight and not loose to avoid damage when the machine is running. The electrical components inside and outside the electrical cabinet of the Cartoning machine must be kept clean and well dissipated.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It will test the Cartoning machine before leaving the factory and provide warranty service. If you are interested in Cartoning machine, you can contact us. Our website is www.cnzpack.com. I look forward to your coming and hope to cooperate with you.
There is already a lot of knowledge about the Labeling Machine in the market, but the Labeling Machine will appear crooked in the process of using it. How should this be solved? Let's take a look together next.
This is the content list:
Reasons for Labeling Machine crooked during use
Labeling Machine appears to "post crooked" solution
Why does Labeling Machine post crookedly during use? There are two factors: one is running in an environment that is not suitable for Labeling Machine work, and the other is the lack of maintenance of Labeling Machine equipment. The round Labeling Machine adopts self-adhesive roll labeling paper, and the labeling adopts the rolling method to complete the labeling process. The self-adhesive Labeling Machine is clean and hygienic, non-mold, beautiful, and firm after labeling, and will not fall off by itself, and production efficiency Higher merits. If you can do both of these things, you can eliminate the problem of inaccurate labeling.
First, stop the Labeling Machine, and then inspect whether the labeling heads on both sides of the Labeling Machine are loose. Use the tools configured by the manufacturer to stabilize the Labeling Machine. Check whether the Labeling Machine wraps the label's trays for looseness or uneven rotation speed. Add engine oil to lubricate. Round bottle Labeling Machine realizes labeling or filming on the circumferential surface of cylindrical and conical products, such as glass bottles, plastic bottles, etc. It can realize circumferential, semicircular, circumferential double-sided, circumferential positioning labeling and other functions, mainly vertical There are two ways of labeling and horizontal labeling. Then inspect the parameters of the Labeling Machine operating system to avoid labeling different products under the same parameters of the Labeling Machine. Finally, adjust the labeling head and place the labeling product separately. When the conveyor belt is conveyed, whether the Labeling Machine shakes or shakes the first two These steps must be performed after the Labeling Machine stops. If the above two cannot solve the labeling problem of the Labeling Machine, please do not disassemble and replace the internal parts of the device privately. You need to transfer the professional to repair the Labeling Machine.
Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. So far, we have more than 100 domestic customers and more than 400 foreign customers. The quality of our Labeling Machine and service as well as our integrity are widely praised at home and abroad. We will carry forward the spirit of "comprehensive innovation and perseverance", self-discipline and strive for the first place, and provide new and old customers with better and more complete services with enthusiasm and a new attitude. It can be seen that we have developed well in the quality of Labeling Machine products. Labeling Machine's first-class product quality and efficient and fast after-sales service have created excellent products of "Zhonghuan". If you are interested in Labeling Machine, you can contact us, our website is www.cnzpack.com. I look forward to your coming and hope to cooperate with you.
Wenzhou Zungwan Intelligent Machine Co.,Ltd. is the professional equipment manufacturer to keep researching and developing the packing machinery for every type of liquid, powder, cream/ointment, fluid and half-fluid etc. materials. We have Obtained ISO9001 quality management system authentication and parts of our products have passed CE authentication. Our company has obtained more than 20 invention patents and utility model patents. The main products range from nail polish filling machine, perfume machine,perfume filling machine, powder serial automatically volume-measuring packing machine and inline capping machine, rotary capping machine and labeling machine, bottle unscrambler , screw capping machine ,tube filling and sealing machine, cartoning machine and other Packaging equipments.
So far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and our service as well as our integrity is acclaimed both in China and abroad. we will carry forward the spirit of "integrated innovation, and perseverance," discipline ourselves to be the first, and provide better and more perfect service for our new and old customers with enthusiasm and a new attitude.