Troubleshooting of cartoning machine supplier- Factory Suppliers Manufacturers From China

After we purchase Pharmaceutical Filler and Capper, we need to install and debug Pharmaceutical Filler and Capper. Let's take a look at it together next.

This is the content list:

l Installation of Pharmaceutical Filler and Capper

l Commissioning of Pharmaceutical Filler and Capper

l Maintenance of Pharmaceutical Filler and Capper

Installation of Pharmaceutical Filler and Capper

According to different models and specifications of Pharmaceutical Filler and Capper, refer to the random manual for installation.

For small-sized Pharmaceutical Filler and Capper, it is not required to build the foundation, just install it on the flat workshop floor, make a good horizontal reference, adjust the elevation of incoming and outgoing chain belt according to the layout diagram, and adjust the legs to make the load of the whole machine evenly distributed.

For large-sized Pharmaceutical Filler and Capper, it is necessary to build a solid installation foundation as required. When installing, the horizontal benchmark should be played, especially when it is connected with the capping machine, the two parts of the incoming and outgoing bottle belts must be at the same horizontal benchmark.

To ensure the smooth bottle delivery of Pharmaceutical Filler and Capper, the inlet pallet under the inlet star wheel should be 0.5mm higher than the surface of the bottle tray, and the outlet pallet under the middle star wheel should be 0.5mm lower than the surface of the bottle tray. The running is free and there should be no jamming interference. The horizontal part of the liquid inlet pipe should have a certain slope to facilitate emptying and air discharge. Make sure the bearing load of Pharmaceutical Filler and Capper's legs is even. Matching equipment with the host, such as gas-liquid control box, vacuum pump system and electric control box, etc. are generally installed separately.

Commissioning of Pharmaceutical Filler and Capper

After confirming the installation of Pharmaceutical Filler and Capper is completed, the commissioning of Pharmaceutical Filler and Capper can be carried out step by step as follows. Replace suitable accessories according to the bottle type filled by Pharmaceutical Filler and Capper, and adjust the parts, including the inlet screw, guide bar spacing, side guard safety switch, star-shaped paddle wheel, reservoir, and capping head height adjustment, etc. Thoroughly clean the Pharmaceutical Filler and Capper reservoir, liquid piping, and gas piping to ensure that there is no foreign material. Make a hydraulic test on the storage tank and pipeline at the same time. Check carefully whether the wiring of the Pharmaceutical Filler and Capper control box is correct, and turn on the main switch only after the equipment is turned manually without jamming. Start the equipment in a pointing way to check if there is any abnormality. Start the Pharmaceutical Filler and Capper at low speed and check the starting, braking, emergency stop, and speed regulation performance. Then infuse an empty bottle at low speed, check whether it can pass through the bottle feed screw, guide bar, and star wheel smoothly and whether each control touch block can respond sensitively. Check whether the Pharmaceutical Filler and Capper can drop the cap smoothly and seal the cap tightly. After that, adjust the value of each instrument on the liquid and gas control cabinet according to the filing requirements of Pharmaceutical Filler and Capper. Check the liquid level and pressure of Pharmaceutical Filler and Capper reservoir, make filling test, adjust the filling head and control the bottling level.

Maintenance of Pharmaceutical Filler and Capper

Pharmaceutical Filler and Capper in the process of use, must be required to carry out regular maintenance. First of all, we must ensure that the lubrication status of the Pharmaceutical Filler and Capper must be good, and the lubrication points must be well-lubricated in time to maintain the oil level of each tank and the intact spray lubrication function. Timely replacement of a variety of damaged parts, such as seals, bottle transport parts, and transmission parts in the wearing parts. The movable parts that are not adjusted for a long time, such as the reservoir of Pharmaceutical Filler and Capper and the height adjustment device of the capping machine, should be run regularly to avoid rust and corrosion. Regularly and regularly clean the liquid tank of Pharmaceutical Filler and Capper, liquid delivery tube, filling valve, and parts that may contact with liquid as required. Liquid residue, oil, water, and glass fragments should be removed to keep the equipment neat and hygienic. Since there are many models and specifications of Pharmaceutical Filler and Capper, and the performance, structure, and working principle vary greatly, operators and maintenance personnel should use and maintain them according to the operation manuals accompanying each machine.

Our products are in great demand in both domestic and international markets, and we are committed to improving and developing to meet our customers and the market demand is our eternal theme and sincere commitment to our customers. If you are interested in Pharmaceutical Filler and Capper, you can contact us, our website is www.cnzpack.com.

ZUNGWAN is the leading manufacturer of perfume and cosmetic filling machines and lines, providing all solutions from the smallest to the fastest machines (400 bpm) for a vast range of applications :

Perfumes (bottles, samples, miniatures), liquid Cosmetics (shampoo, conditioner, lotions, gel, serum, foam bath, liquid soap, shower gel, hair dye, nail varnish, foundation, makeup remover, suntan lotion, deodorant, roll-on, etc.) and Cosmetic creams (jars, lip-gloss, mascara).

Wenzhou Zungwan Intelligent Machine Co.,Ltd. is the professional equipment manufacturer to keep researching and developing the packing machinery for every type of liquid, powder, cream/ointment, fluid and half-fluid etc. materials. We have Obtained ISO9001 quality management system authentication and parts of our products have passed CE authentication. Our company has obtained more than 20 invention patents and utility model patents. The main products range from nail polish filling machine, perfume machine,perfume filling machine, powder serial automatically volume-measuring packing machine and inline capping machine, rotary capping machine and labeling machine, bottle unscrambler , screw capping machine ,tube filling and sealing machine, cartoning machine and other Packaging equipments.

So far we have more than 100 domestic customers and more than 400 foreign customers. The quality of our machines and our service as well as our integrity is acclaimed both in China and abroad. we will carry forward the spirit of "integrated innovation, and perseverance," discipline ourselves to be the first, and provide better and more perfect service for our new and old customers with enthusiasm and a new attitude.

The tube Filling machine And the Sealing machine are determined by multiple parameters. It is impossible to describe a Tube Filling machine And Sealing machine with any single parameter. Shaft power, blade displacement, pressure head, blade diameter, and filling speed are the five basic parameters that describe a Tube Filling Machine And Sealing machine. So, let's take a look at the principle of the Tube Filling machine And Sealing machine together. Here are some answers.

Here is the content list:

l Basic parameters.

l The shear rate of the fluid.

l Small slot and big slot.

Basic parameters.

The displacement of the blade is proportional to the flow rate of the blade itself, the first power of the blade speed, and the third power of the blade diameter. The shaft power consumed by the filling is proportional to the specific gravity of the fluid, the power standard of the blade itself, the third power of the speed, and the fifth power of the blade diameter. In the case of a certain power and blade form, the blade displacement and pressure head can be adjusted by changing the diameter of the blade and the matching of the speed. That is, the large diameter blade is equipped with a low-speed Tube Filling machine And a Sealing machine. High flow effect and low-pressure head, while the small diameter blade with high speed produces a higher pressure head and lower flow effect.

The shear rate of the fluid.

In the filling tank, the only way to make the micelles collide with each other is to provide a sufficient shear rate. According to the mechanism of the Tube Filling Machine And Sealing machine, it is because of the existence of fluid velocity difference that the fluid layers are mixed. Therefore, where the filling process always involves the fluid shear rate lhhaha620. Shear stress is a force that is the real cause of bubble dispersion and droplet breaking in filling applications. It must be pointed out that the shear rate at each point of the fluid in the entire stirred tank is not the same.

Small slot and big slot.

Experimental research shows that, as far as the blade area is concerned, no matter what type of blade, when the diameter of the blade is constant, the maximum shear rate and the average shear rate increase with the increase of the speed. However, when the rotation speed is constant, the relationship between the maximum shear rate and the average shear rate, and the diameter of the blade is related to the slurry type. When the rotation speed is constant, the maximum shear rate of the radial blade increases with the increase of the blade diameter, and the average shear rate has nothing to do with the diameter of the blade. These concepts about the shear rate of the blade area require special care in the design of the Tube Filling Machine And Sealing machine to reduce and enlarge. Because the small groove is compared with the large groove, the small groove Tube Filling Machine and Sealing machine often has the characteristics of high speed, small blade diameter, and low tip speed. The large groove Tube Filling Machine And Sealing machine often has the characteristics of low speed, large blade diameter, and high tip speed.

Our official website is https:// www.cnzpack.com/. If you are engaged in work related to the Tube Filling machine And Sealing machine, you can communicate with us on the website.

In our production and life, Capping Machine is also called a Capping Machine, Capping Machine, or Capping Machine, which is used for screwing and unscrewing the caps of plastic bottles and glass bottles (molded bottles or tube bottles). equipment. Capping Machine is highly intelligent capping equipment with advanced technology, unique design, and easy operation. During the entire capping process, workers only need to place the cap on the mouth of the bottle, and then the bottle is automatically sent to the capping wheel and automatically tightened to complete the capping operation. The Capping Machine evacuates the packaging bottle and then tightens it, which prolongs the storage time of the packaging, reduces the failure rate of the Capping Machine, and improves the packaging efficiency of the Capping Machine. So what are the matters needing attention when operating Capping Machine correctly? Let's take a look together next.

This is the content list:

l Capping Machine rolling wheel adjustment

l Capping Machine lock wheel adjustment

l Capping Machine cap lock

l Capping Machine height adjustment

Capping Machine rolling wheel adjustment

Place the Capping Machine bottle on the bracket and raise the bracket to the highest point. First, loosen the lock nut to adjust the rolling wheel so that the (sprung) edge of the two Capping Machine rolling wheels is at the threading of the bottle. Click on it, then loosen the lock nut, and then adjust the adjusting screw so that the edges of the two rolling wheels are in contact with the cover, and a little pressure is appropriate, and then tighten the nut.

Capping Machine lock wheel adjustment

Adjust the two Capping Machine locking wheels, first loosen the locking nuts, adjust the locking wheels so that the edges of the two locking wheels are in contact with the lower edge of the bottle cap, a little pressure is appropriate, and then tighten the nuts (Note: Adjust Capping Machine Should be from loose to tight, adjust while pulling the lock).

Capping Machine cap lock

Loosen the top screw, remove the Capping Machine gland head, and then remove the entire Capping Machine lock head, install the appropriate plastic lock head on the cone sleeve, and then adjust the lifting height of the bracket to meet the working requirements.

Capping Machine height adjustment

Start the Capping Machine to lower the bracket to the lowest point, then place the bottle on the bracket, loosen the brake nut, turn the adjusting screw to raise the bracket, and then adjust the appropriate distance between the cap of the Capping Machine and the capping head (generally All are adjusted in place at the factory).

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops various packaging machinery for liquid, powder, cream/ointment, fluid, and semi-fluid materials. We have obtained ISO9001 quality management system certification, and some products have passed CE certification. Our company has obtained more than 20 invention patents and utility model patents. If you are interested in Capping Machine, you can contact us, our website is www.cnzpack.com.

In our daily life, Capping Machine plays a vital role for us, so what are the main work processes and precautions of the Capping Machine? Let's take a look together next.

This is the content list:

• The main workflow of Capping Machine

• How to carry out daily maintenance and maintenance of Capping Machine

• How to deal with common problems of Capping Machine　

The main workflow of Capping Machine

We know that after the plastic bottles are sorted by the Capping Machine, they enter the conveyor chain in a single row. In the filling station, the plunger pump injects the liquid in the container into the plastic bottle. After filling, the plastic bottle enters the index plate and stops accurately at the capping station. Manually place the cap of the Capping Machine at the entrance of the friction beltline, take out the capping claw, screw the cap claw, and squeeze the tube claw to complete the capping action. Then the plastic bottle exits the index plate and enters the conveyor chain, and enters the labeling station to complete the round bottle labeling.

How to carry out daily maintenance and maintenance of Capping Machine

1. Always keep the Capping Machine clean, especially for the electrical appliances on the switchboard, to prevent moisture and dust, and it is forbidden to change the program of the inverter and the program controller at will.　

2. The power supply voltage of the Capping Machine should be stable, not exceeding ±15%, the material temperature should be kept at 10℃-40℃, the ambient temperature should be kept at 5℃～40℃, and the temperature should be kept at 5～95%PH.　

3. The flowmeter used by the Capping Machine for spray filling is a precision instrument. Therefore, the oil must be precision filtered before it can be filled.　　

4. Turn off the power supply and oil inlet valve of the Capping Machine after finishing the work.　　

5. Pay attention to the cleanliness of the infrared sensor from the Capping Machine. Frequently wipe it clean with clean cotton. It is strictly forbidden for any object to approach the sensor during the working process, and strong light should not be directly or reflected on the sensor, otherwise, it will prosper and malfunction.

6. Add cylinder lubricating oil to the pneumatic triplet regularly.　　

7. When the machine is not used for a long time, all parts should be wiped clean and covered with plastic or tarpaulin to prevent dust.

How to deal with common problems of Capping Machine

First, what should I do if the cylinder piston of the Capping Machine does not work? Confirm whether the safety emergency stop switch is safe. Confirm that the air supply switch of the Capping Machine is turned on. Check if the Capping Machine one-way signal valve is damaged.

Second, what should I do if the Capping Machine cylinder piston does not return after being pushed to the top? Confirm whether the moving target is in contact with the one-way valve.

Third, how to adjust the filling volume of the Capping Machine is inaccurate or not discharged?

Check whether the upper and lower throttle valves of the Capping Machine are closed, and increase the pumping speed of the throttle valve of the cylinder. Make sure that the Capping Machine quick-install tee is locked with a clamp. Confirm whether there are enough materials in the Capping Machine storage box. Make sure that the joints of the pipes of the Capping Machine are sealed.

Fourth, what should I do if the material of the Capping Machine flows out from the rear end of the cylinder? Check whether the sealing ring on the Capping Machine piston is worn. If it is worn, replace it and make sure that the piston and the piston rod are tight.

In addition to timely handling of problems, it is also necessary to do a good job of preventive work in advance. Doing a good job in daily maintenance can also reduce the failure rate of the Capping Machine. The daily maintenance and maintenance of the Capping Machine cannot be underestimated. This is a very important step. Daily maintenance on time can effectively extend the service life of the Capping Machine, improve the production efficiency of the enterprise, and keep Capping Machine in normal operation throughout the day, reducing manpower. The loss of material resources.

Wenzhou Zungwan Intelligent Machinery Co., Ltd.'s first-class product quality and efficient and quick after-sales service have created excellent products of "Zhonghuan". Products are in great demand in the domestic and foreign markets. Keep improving, develop to satisfy customers, and meet market demands are our eternal topic and our sincere commitment to customers. Therefore, Capping Machine is very popular among consumers. If you are interested in Capping Machine, you can contact us. Our website is www.cnzpack.com.

Speaking of Bag packaging machines for large machinery, it is necessary to briefly talk about the knowledge of stand-up pouches. Bag packaging machines in the application, development, and growth of stand-up pouches played a role in what? Let's look at it together next.

This is the list of contents:

• Stand-up pouches in brief

• The basic classification of stand-up pouches

Stand-up pouches in brief

Stand-up pouches produced by Bag packaging machines are flexible packaging bags with a horizontal support structure at the bottom. It does not rely on any support, whether the bag is opened or not, it can stand on its own. Since its appearance and promotion, stand-up pouches have been very popular. With their good design and function, they have been widely used in food, daily necessities, pharmaceuticals, and other fields. Stand-up pouches produced by Bag packaging machines are mainly used for juice drinks, sports drinks, spices, and other products. In addition to the food industry, the application of some Bag packaging machine products such as detergents, daily cosmetics, pharmaceuticals, etc. is gradually increasing.

The basic classification of stand-up pouches

1. Ordinary stand-up pouches

That is, the general form of the Bag packaging machine produced by the stand-up pouches in the form of four seals, cannot be resealed and reopened. This stand-up pouch packaging machine to produce stand-up pouches is generally used in the industrial supplies industry.

2. Stand-up pouches with suction nozzles

Stand-up pouches with suction nozzles produced by the Bag packaging machine are more convenient to pour or suck out the contents and can be re-closed and re-opened at the same time. It can be thought of as a combination of stand-up pouches and ordinary bottle spout.

3. Stand-up pouches with zipper

Stand-up pouches with zippers produced by the Bag packaging machine can also be re-closed and re-opened. As the zipper produced by the Bag packaging machine is not closed, the seal strength is limited, so this form is not suitable for packaging liquids and volatile substances.

4. Special-shaped stand-up pouches

That is, according to the packaging needs, based on the traditional packaging bags, change the Bag packaging machine production of a variety of new shapes of stand-up pouches, such as waist design, bottom deformation design, handle design, etc.

Bag packaging machine production of stand-up pouches not only improves the product grade, but also strengthens the visual effect of the shelf, and is easy to carry, easy to use, with good preservation and sealing performance. The development of stand-up pouches produced by the Bag packaging machine, but also the packaging machinery industry to follow the trend, the development of adaptable Bag packaging machine.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer that continuously researches and develops a wide range of packaging machinery for liquid, powder, cream/paste, fluid, and semi-fluid materials. We have obtained ISO9001 quality management system certification and some of our products have passed CE certification. Our company has obtained more than 20 invention patents and utility model patents. Our main products include a nail polish filling machine, perfume machine, perfume filling machine, powder series automatic quantitative packaging machine and in-line capping machine, capping machine and labeling machine, bottle management machine, tube filling and sealing machine, cartooning machine, and other packaging equipment. If you are interested in a Bag packaging machine, you can contact us, our website is www.cnzpack.com.

In our production and life, the Cartoning Machine is of great significance to us, but sometimes, the Cartoning Machine will fail, so what is the reason for the failure of the Cartoning Machine? Next, let us analyze it together.

This is the content list:

• Stop or stop between conveyor belts

• The carton cannot be sucked down

• The carton is not formed or ejected at the mouth of the box feeding template after being sucked

• Can't suck the instructions

• The paper rebounds during the suction process of the manual

• The manual does not fold well

• Uneven folding of the manual

• There are curls and creases after the manual is folded

• Manual stuck in the fence

Stop or stop between conveyor belts

1. Cartoning Machine shuts down at intervals to check if there is a shortage of materials and automatically starts up when supplemented.

2. Shut down the Cartoning Machine to check whether the power supply including the power supply part, the motor, or the governor is normal.

The carton cannot be sucked down

1. Whether the cartons of Cartons Machine are arranged neatly.

2. Whether the cartons of the Cartoning Machine are pasted together.

3. Whether the air pressure of the Cartoning Machine suction head is normal.

The carton is not formed or ejected at the mouth of the box feeding template after being sucked

1. Check if the cartons of Cartons Machine are too hard.

2. Check whether the position of the guide rod of the cartons placed by the Cartoning Machine and the box delivery template are not correct.

3. Check whether the small hook spring at the rear of the Cartoning Machine delivery template is deformed.

4. Check if the height of the suction head of the Cartoning Machine and the box delivery track is correct.

Can't suck the instructions

1. Whether the Cartoning Machine manual is deformed, causing the suction head to fail to suck.

2. Whether the suction head gas of the Cartoning Machine is parallel to the manual.

3. Whether the paper width of the Cartoning Machine manual is different, the error must be within 1mm. The stacking position of the manual should be adjusted to a difference of 0.5mm from the inner edge when the suction head rises to the high position.

4. The small paper-separating hook above the suction head of the Cartoning Machine origami moves too early. Generally, the small hook should be inserted into the gap between the paper and the paper before the suction head is about to drop. The height of the small hook is adjusted to be 0.5mm away from the suction head when it is in the high position.

The paper rebounds during the suction process of the manual

1. The foot-lifting action of the Cartoning Machine's manual was too early, and the manual was taken away by the foot support before being pulled down. The position of the feet of the Cartoning Machine is so that it does not touch the sucked manual when it is returned and it returns to the high position when the paper picking notch wheel has not pulled the paper.

2. Whether the matching speed of the Cartoning Machine suction head and paper picking wheel is the same. The suction head of the Cartoning Machine should be lowered first, and then the front part of the paper picking notch wheel should be pressed onto the paper.

The manual does not fold well

1. Check if the Cartoning Machine paper is deformed and bent, and if there are burrs.

2. Is there any foreign matter in the fence of the Cartoning Machine blocking the paper?

3. The gap between the opening of the Cartoning Machine fence and the folding stick is too large, causing the paper to come out.

4. Is the gap between Cartons Machine's folding sticks too large to hold the paper? Adjust the adjusting screws at both ends of the folding stick to reduce the gap. If the Cartoning Machine folding stick has been used for too long and worn out, the folding stick must be replaced.

Uneven folding of the manual

Check the Cartoning Machine to adjust the front and rear positions of the barriers in the fence to achieve the required folding size.

There are curls and creases after the manual is folded

1. Is the gap between the Cartoning Machine baffle and the folding stick too large? Adjust the middle position of the baffle and folding stick.

2. If the middle position of the Cartoning Machine baffle and the folding stick has been adjusted, and there is still a large gap, remove the positioning pins on the Cartoning Machine baffle and re-adjust until the gap does not feed paper.

Manual stuck in the fence

1. Whether the paper feeding gap of Cartoning Machine folding stick is too large and paper feeding is weak. The adjustment method is the same as above.

2. The installation position of the lower half of the Cartoning Machine fence is too long than the arc guide plate on it so that the paper cannot enter the folding stick below. Loosen all the fixing screws on the Cartoning Machine fence and adjust the board backward, but it should not be shorter than the upper guide plate and should be 1-3 mm longer than the guide plate. If it is shorter than the guide plate, the Cartoning Machine manual may go directly into the folding stick below without folding.

Wenzhou Zungwan Intelligent Machinery Co., Ltd. is a professional equipment manufacturer. It will conduct a large number of tests before the Cartoning Machine leaves the factory to reduce the failure of the Cartoning Machine and provide warranty services. If you are interested in the Cartoning Machine, you can contact us Contact, our website is www.cnzpack.com.

ASPRO maxi model tube filling machine runs on elliptical runway model with double head The machine runs at a speed up to 120 tubes / min according to the tube type Driven by Ferguson indexing system with suitable reverse lock All the product contact parts are made of SS 316 l matching to pharma grade requirement

Piston Filler We manufacture different types of rotary Piston Fillers, which are suitable to fill volumetri

orangea manual liquid filling machine on sale manufacturers, find details about orangea manual liquid filling machine manufacturers, supplier and wholesaler - Wenzhou Zungwan Intelligent …

Wet Glue Labeling Machine; Self-Adhesive Sticker Labeling Machine; Wet Glue Labeling Machine: It is considered to be one of the most user-friendly machines that one will ever come across. The machine is compatible with flat, square, round or rectangular bottles capable of attending up to 120 containers per minute depending on the bottle and label size.

Horizontal End-Load Cartoning Machine refers to those cartoning machines that erect carton blanks with their top and bottom facing horizontally, and the rear and front panels are facing top and down. Horizontal End-Load cartoning machines can be either intermittent or continuous motion cartoning machines.

Small sachets seasoning packing machine for spices. accupacking 19-11-6. Spice Packaging Machine - . 15349 products accupacking offers 15349 spice packaging machine products. About 52% of small cheap and best dry spice powder packing machine 2-100g. ... Small Sachet packing powder machine For Powder of Food,Chili . Feb 6, 2015 good ...

It is available for series of round and flat perfume bottles. And it adopts stainless piston measuring pump for vacuum filling, pneumatic capping, and rising-and-falling screwing. The machine enjoys advantages of accurate measurement, stable screwing and easy operation, widely used in pharmaceuticals and cosmetics industry.

NF-100 Cream Soft Tube Filling Sealing Machine NF-30 semi-automatic tube filling sealing machine NF-80 Automatic Al Aluminum/Plastic Soft Tube Filling and Sealing Machine Lotion NF-120 Fully automatic Plastic tube and aluminum tube filling sealing machine NF-60 Automatic Plastic/Laminated Tube Filling